Back
[01:17:30] <toast> bam
[01:26:23] <CIA-22> 03jepler 07TRUNK * 10emc2/src/hal/classicladder/config_gtk.c: the "Physical Inputs" and "Physical Outputs" pages should not appear; this is handled in emc via hal
[01:37:27] <CIA-22> 03jepler 07TRUNK * 10emc2/src/hal/classicladder/classicladder.h: somehow this file got into DOS mode
[01:39:30] <Ito> Hello ALL
[01:39:52] <Ito> have anyone seened something about DIY EMBROIDERY Machines ?
[01:41:24] <cradek> I think someone on the emc-users list mentioned an embroidery project, it was a long time ago
[01:42:29] <Ito> wow
[01:42:44] <Ito> I´m thinking in build one...
[01:46:11] <toast> go for it
[01:46:25] <Ito> I only need a software, lol
[01:46:36] <Ito> do EMC2 runs it?
[01:46:40] <toast> i don't see why you couldn't rig emc up
[01:46:42] <toast> to do it
[01:46:51] <toast> i mean i AM an idiot
[01:47:07] <Ito> well i am MORE THAN YA lol
[01:47:27] <Ito> I could not realize how to do it on EMC
[01:47:42] <Ito> if i can do it, of course i will use it
[01:47:47] <CIA-22> 03jepler 07TRUNK * 10emc2/src/hal/classicladder/ (6 files): quiet many messages
[01:48:53] <CIA-22> 03jepler 07TRUNK * 10emc2/src/hal/classicladder/ (arrays.c classicladder.c): somehow this file got into DOS mode
[02:49:08] <CIA-22> 03jepler 07TRUNK * 10emc2/src/hal/utils/ (halcmd_commands.c halcmd_main.c): fix help to add some new commands and get rid of linkpp
[02:51:30] <CIA-22> 03jepler 07TRUNK * 10emc2/src/hal/utils/halcmd_commands.c: additional help improvements
[02:51:46] <CIA-22> 03jepler 07TRUNK * 10emc2/src/hal/utils/halcmd_completion.c: completion of 'source', 'ptype', 'stype'
[02:53:41] <CIA-22> 03jepler 07TRUNK * 10emc2/src/hal/utils/halcmd_completion.c: complete source command with arg from filesystem
[03:21:41] <SWPadnos_> SWPadnos_ is now known as SWPadnos
[04:16:59] <skinnypuppy34> zzzz....anyone round?
[04:17:37] <LawrenceG> snort..snort hey skinnypuppy34
[04:18:03] <skinnypuppy34> Hi.
[04:18:34] <LawrenceG> kind of quiet tonite on the west caost of Canada
[04:19:22] <LawrenceG> I have been staring at an eagle screen trying to figure out how to place parts on a breakout board I am working on
[04:19:28] <skinnypuppy34> I was wondering about all the holes in 1 2 3 blocks, I can think of why it has threaded holes , but why all the blank non reamed holes?
[04:20:03] <LawrenceG> easier to hold onto so you dont drop it?
[04:20:21] <skinnypuppy34> perhaps...
[04:20:37] <skinnypuppy34> What size board will that free eaglesoft do again ?
[04:21:03] <LawrenceG> something like 3.5x4"
[04:22:22] <skinnypuppy34> Not bad, I had played with it about 30 minutes a few years ago, long enough to throw a little 8 pin op amp and some resistors cap on the screen to see what it would do .
[04:23:19] <LawrenceG> its quite good, but it is worth doing the tutorial because eagle is not very intuative
[04:24:10] <skinnypuppy34> I remember finding that much so
[04:24:42] <LawrenceG> http://imagebin.ca/view/KgjUSH.html
[04:25:39] <LawrenceG> http://imagebin.ca/view/LUKwfTOu.html
[04:26:54] <skinnypuppy34> Looks nice... wish all these cool things were around when I was really into electronics...
[04:27:56] <skinnypuppy34> Hi alex
[04:28:17] <LawrenceG> it is preety neat being able to design a circuit, layout the board, mill it with emc and build it within a day or 2
[04:28:53] <LawrenceG> late nite alex?
[04:30:46] <skinnypuppy34> I'm certain! I'm trying to set up a tool blank to use the surface grinder to make a single point tool for making my .2 pitch pulleys.
[04:31:34] <LawrenceG> cool... I always wanted to try that.... take some pictures and add a page on the wiki