#linuxcnc | Logs for 2012-05-05

Back
[00:00:53] -!- asdfasd has quit [Ping timeout: 248 seconds]
[00:04:06] <ReadError> r00t4rd3d: the fireball is nice
[00:05:48] <r00t4rd3d> that little furnace he has is cool
[00:07:29] -!- factor [factor!~factor@r74-195-219-241.msk1cmtc02.mskgok.ok.dh.suddenlink.net] has joined #linuxcnc
[00:09:10] <r00t4rd3d> I could do stuff with that
[00:11:19] <r00t4rd3d> I wonder if it would melt aluminum
[00:14:11] <roycroft> easily
[00:14:28] <roycroft> the little kiln i just bought will melt aluminum
[00:14:57] <roycroft> aluminum melts at 660c
[00:15:03] <roycroft> you can melt it with a propane torch
[00:18:20] -!- iwoj has quit [Read error: Connection reset by peer]
[00:20:05] -!- rob_h has quit [Ping timeout: 250 seconds]
[00:20:30] -!- cylly2 [[email protected]] has joined #linuxcnc
[00:20:58] -!- iwoj [[email protected]] has joined #linuxcnc
[00:21:51] -!- Loetmichel has quit [Ping timeout: 252 seconds]
[00:28:25] -!- PCW has quit [Quit: ChatZilla 0.9.88.1 [Firefox 3.6.13/20101203075014]]
[00:40:46] <jdhNC> ctj: they are "those green plug in phoenix connector things"
[01:12:07] <r00t4rd3d> http://www.ebay.com/itm/PHOENIX-CONTACT-1792058-MVSTBR-2-5-6-ST-plug-/190560554527?pt=LH_DefaultDomain_0&hash=item2c5e4b4e1f
[01:12:14] <r00t4rd3d> in new york and cheaper then digi
[01:14:58] <jdhNC> if you just need one, I have a 6 sitting here.
[01:15:23] <r00t4rd3d> "combicon plug"
[01:15:31] <r00t4rd3d> I guess is the proper name for them
[01:16:14] <jdhNC> there are lots of names. Lots of places make them. McMaster has them
[01:31:32] <ctjctj> thank you r00t4rd3d I've got it covered now. You guys got me to the right place which is what I was asking for.
[01:32:16] <ctjctj> In the mean time I'm finding programming in g-code/o-code to be frustrating at best and dangerous to equipment at worse
[01:33:29] <ctjctj> Stupid little things like 38.5 will break contact with my touch plate but there is still spring so the g0z(up) gives me "probe fired during non-probe mdi"
[01:48:27] <cradek> maybe you need to debounce it?
[02:01:36] <ctjctj> Mechanically or electronicly?
[02:02:29] <r00t4rd3d> did you make your touch plate?
[02:03:13] <ctjctj> yep. wire to piece of pcb board. other end to ground. alligator clip to bit, other end to in.motion pin.
[02:04:25] <r00t4rd3d> there is so much i need to learn
[02:04:55] <ctjctj> Same here.
[02:04:59] <r00t4rd3d> think i am just gonna smoke crack instead
[02:06:42] <r00t4rd3d> I hate myself for liking The Big Bang Theory on TV.
[02:07:11] <jdhNC> she used to be hot and you used to want to be 'that guy'?
[02:09:06] <ctjctj> Ok. why did my feedspeed for rapids drop suddenly? Makes no sense to me...
[02:09:30] <jdhNC> did you change feed override or max speed?
[02:13:06] <ctjctj> nope.
[02:13:41] <ctjctj> Everything seemed to be working correctly. Then I did a g54 g1z0.85f2 and after that all movement was "slow"
[02:13:58] <Aero-Tec> KimK: are you around?
[02:14:08] <Aero-Tec> got up for a bit
[02:14:15] <jdhNC> G0 is slow, or just all G1?
[02:14:20] <ReadError> i gotta admit
[02:14:26] <ReadError> i been trying alot of drafting programs
[02:14:30] <Aero-Tec> will stick around awhile
[02:14:31] <ReadError> the best by FAR is solid works
[02:14:37] <ReadError> its super intuitive
[02:14:47] <Aero-Tec> I use solid works
[02:14:53] <Aero-Tec> great program
[02:14:58] <ReadError> wish they had a hobby version
[02:15:02] <Aero-Tec> not cheap
[02:15:02] <ctjctj> g0 is slow.
[02:15:05] <ReadError> 12k....
[02:15:06] <ReadError> jesus
[02:15:21] <ReadError> its like come on guys, i dont need all the motion stuff
[02:15:25] <ReadError> just gimme the modeling!
[02:15:47] <ReadError> Aero-Tec, what do you use to convert to gcode?
[02:15:49] <ReadError> thats where im at now
[02:15:52] <jdhNC> I went to a design review last week for a new machine we are having built. Their mechanical guy had done it all in SW and made it look really impressive (cylinders extending, everything moving, etc)
[02:15:54] <Aero-Tec> there are some hacked versions out there
[02:15:56] <ReadError> pycam seems to have issue
[02:16:04] <ReadError> Aero-Tec, ;)
[02:16:10] <Aero-Tec> I have bob cam for solid works
[02:16:17] <ReadError> oh? does it work nicely?
[02:16:28] <Aero-Tec> but I hand code most of my stuff
[02:16:37] <ctjctj> Problem started with a G28.1 which sets my goal. G28 Z3 which should raise the Z to abs 3in but it didn't. Just took off for the goal xyz
[02:16:48] <ctjctj> pycam is not may favorite software. :-(
[02:17:09] <ReadError> its good for some stuff
[02:17:21] <ReadError> but for instance, i have a 0.125" endmill
[02:17:29] <ReadError> and it doesnt do my 0.125 holes
[02:17:37] <ReadError> i just want it to drill down...
[02:17:57] <ctjctj> Got my code output good g-code for profiles (inside, outside, on) but then got burned out trying to draw a stupid graphic for the UI to show climbing vs. conventional cutting.
[02:18:06] <Aero-Tec> use cam for fancy 3D models, but even then I only cam the fancy curves and contours, the rest is hand coded
[02:18:13] <ReadError> i dont like how it resets everything when your restart it
[02:19:23] <Aero-Tec> yes bob cam for solid works is nice, but then again not cheap
[02:19:35] <ReadError> is there a ....version?
[02:19:45] <jdhNC> I've never used G28. Might be hazardous the way I leave things around.
[02:20:50] <Aero-Tec> I started machining for myself, but every thing I needed was so expensive that I started machining for others so I could afford the nice programs
[02:20:52] <ReadError> visualmill made a nice path
[02:21:00] <ReadError> but its payware....
[02:21:01] <ctjctj> I'm using it to move to the "tool touch plate" Seemed like the "right" way to do it. Looks like I should just use a couple of g53 g0 lines. Less fancy more reliable
[02:21:47] <Aero-Tec> BTW, bob cad cam had a stripped down version of solid works for $1500 I think that was what it was
[02:22:06] <ctjctj> Aero-Tec: I wish I could sell things but the software is so expensive I decided to write the software myself. Slow going. I know *how* to do most of the things I want to do. It is now just a small mater of programming it.
[02:22:32] <Aero-Tec> I was dealing with the solid work rep and then BOB cad offered me this deal
[02:22:45] -!- FinboySlick [[email protected]] has joined #linuxcnc
[02:23:52] <Aero-Tec> my solid works rep was shocked and also felt ripped as he could not offer me anything even close to it and he had also never even heard of that version that BOB cad was offering
[02:24:49] <ReadError> hmmmmm they have a trial apparantly
[02:24:57] <ReadError> <3 vmware esxi snapshots
[02:25:21] <ReadError> wonder if it is full featured or the gimp version
[02:28:36] <Aero-Tec> I write most code using variables and subs. like planing a surface, size of mill bit, start of x end of x, start of y and end of y, hit go and it is done all through preprogrammed sub
[02:29:05] <jdhNC> you should make a full featured conversational programming interface for me.
[02:29:06] <Aero-Tec> it is a gimp version, no 2D stuff and a few other things
[02:30:06] <Aero-Tec> maybe we should start a group
[02:30:29] <Aero-Tec> one that does programmable Gcode
[02:30:57] <Aero-Tec> just punch in some numbers and hit go
[02:31:43] <ctjctj> Aero-Tec: I'm scared to do that. I'm afraid that I'll find out that everybody else's g-code interpreter does it just a little bit differently.
[02:31:55] <jdhNC> but only one matters.
[02:32:06] <ctjctj> I'm afraid to go look and find out that o codes are only linuxcnc.
[02:32:13] <ctjctj> jdhNC: *GRIN* that is one way of looking at it.
[02:32:51] <Aero-Tec> I wrote my own code for drilling, facing reducing the dia in the lathe, boring, it is all done with subs and a few variables, punch in the values and load the sub and hit go
[02:35:26] <Aero-Tec> I used them in mach, but mach suck, no conditional branches, that made some things very difficult to program, but I was able to do it
[02:35:50] <Aero-Tec> had to think way outside the box
[02:36:00] <ctjctj> *nods* I can believe it.
[02:36:55] <ctjctj> I've not tested if you can do #31=1024 #[#31]=55 to be able to set #1024 to the value of 55
[02:37:09] <Aero-Tec> I very much look forward to using named variable and conditional branches
[02:38:07] <Aero-Tec> why not just use #1024=55
[02:38:22] <Aero-Tec> you taking a very long way around
[02:39:21] <Aero-Tec> I would have to check the manual, I am very new to EMC
[02:39:40] <ctjctj> Aero-Tec: think of a loop where #31 goes from 0 to 8 so that you can move all of a coordenate tuple in a loop rather than #31=#5061 #32=#5062... #39=#5069
[02:39:44] <Aero-Tec> in fact I just started yesterday with my lathe, mill is next
[02:40:30] <Aero-Tec> got mad at mach for the last time
[02:40:31] <ctjctj> in a fuller language it would be "for (int i=0; i<9; i++) a[i] = b[i];"
[02:40:42] <Aero-Tec> finaly made the jump to EMC
[02:41:09] <ctjctj> Aero-Tec: good for you. LinuxCNC is great. I've been playing with it for 4-5 years. Actually using it for about 6 weeks.
[02:42:30] <r00t4rd3d> o_O
[02:44:00] <r00t4rd3d> how do you play with it?
[02:44:04] <r00t4rd3d> Sim
[02:44:10] <ctjctj> Yep, sim.
[02:44:37] <ctjctj> But you don't see things the same way. Like just how important it is to be able to zero your tools *exactly* when you change tools.
[02:44:50] <ctjctj> Or how fast this thing can really make chips and move.
[02:44:55] <Aero-Tec> you know, with programmable Gcode one could do a ton of things like center of bolt pattern distance from center and number of holes, in just a few second you could have the whole thing programmed and running
[02:45:22] -!- demacus_ has quit [Read error: Operation timed out]
[02:45:22] <ctjctj> There might even be canned cycles for that.
[02:46:33] <Aero-Tec> that was just a example, but if that is a canned cycle in EMC that would be cool
[02:46:37] <ctjctj> r00t4rd3d: or another one that got me: There is no model for absolute positioning. This becomes an issue when you have motion commands that only work in a corrdenate system. I.e. does not accept a G53 prefix.
[02:46:48] <Aero-Tec> mach had no such thing
[02:46:57] <ctjctj> Aero-Tec: have you looked at some of the example nc files?
[02:47:17] <r00t4rd3d> you could have wrote that in Mandarin Chinese.
[02:47:18] <Aero-Tec> not yet
[02:47:36] <ctjctj> Aero-Tec: take a look. Lots of good exmaples.
[02:48:10] <Aero-Tec> well I very quick look, but not opened them, did open one or two
[02:48:38] <ctjctj> r00t4rd3d: the primary g code to move the cutter is "g0" and "g1" you give them a command like "g1 x3 y 4 z2" which says "move to the point (3,4,2) in a straight line at the current feed rate"
[02:48:43] <Aero-Tec> but did not look them over like I would like
[02:49:06] <ctjctj> but linuxCNC (and maybe others) has the concept of offset coordinate systems.
[02:49:17] <ctjctj> In computer graphics we call them "local coordinate systems"
[02:49:22] <Aero-Tec> I was looking for why EMC kept complaining about how I ended my Gcode
[02:50:19] <ctjctj> When you start linuxcnc you need to home your axis. This moves each axis to a known location and at that point you know the "absolute (global)" position of the cutter.
[02:50:22] <Aero-Tec> that is what Kin K is helping me with, he is looking over my code and trying to tack down what EMC does not like about it
[02:50:38] <r00t4rd3d> is it an absolute must i learn gcode?
[02:51:01] <r00t4rd3d> I perfer cp coding
[02:51:06] <ctjctj> That's what the home button in axis does. If it says "home all" it does it all automagically. If not then you jog the cutter to the right place and home each axis.
[02:51:08] <Aero-Tec> I did a quick and dirty conversion of some mach code, EMC did not like it at all
[02:51:17] <Aero-Tec> and I can not find out why
[02:51:36] <ctjctj> After that the machine/controller needs to know where your work is. That is done with "touch off"
[02:52:06] <ctjctj> you move the cutter to a place which going to be the zero for your work. You then "touch off" the x,y axis.
[02:52:13] <Aero-Tec> what is CP coding?
[02:52:25] <r00t4rd3d> Copy/Paste.
[02:52:28] <ctjctj> you don't need to learn g-code. Many people I'm sure never learn gcode. But it does make somethings much easier.
[02:52:34] <Aero-Tec> and yes it is of great help to know Gcode
[02:52:37] <Aero-Tec> lol
[02:53:16] <ctjctj> once you have touched of x,y,z you now have offsets. They are stored in a local coordinate system. G54 by default.
[02:53:25] <Aero-Tec> some just use cam to gen the Gcode
[02:53:50] <ctjctj> so now when you say "g1 x3 y2" it goes to (3,2) PLUS the G54 offsets.
[02:54:05] <Aero-Tec> but I can not imagine doing CNC and not knowing Gcode
[02:54:06] <ctjctj> This means that you don't have to put your work piece at the zero location of your machine.
[02:54:31] <Aero-Tec> you have to be able to speak the language the machines understands
[02:54:55] <Aero-Tec> that way you can tweak things and speed things up
[02:54:57] <ctjctj> r00t4rd3d: here's an example for you. You want to move your cutter out of the way for some reason. You can press keys and move the cutter head with the arrows and page up/page down till you get the cutter where you wnat it.
[02:55:42] <Aero-Tec> you know all the extra move most cam program generate? well it you know Gcode you can get rid of them
[02:55:50] <r00t4rd3d> I can use a PS2 controller to manually control my controller
[02:56:03] <ctjctj> or you can type "<F5> g53 g0z3 \rg53 g0x0y0" and send the cutter straight up and then over to the machines 0,0 location.
[02:57:03] <r00t4rd3d> how hard is it to like find a image on the net and carve into wood
[02:57:15] <ctjctj> how much do you want to pay?
[02:57:19] <Aero-Tec> if you just making one or 2 of any one thing then that is OK
[02:57:26] <r00t4rd3d> pay
[02:57:32] <r00t4rd3d> nothing
[02:57:55] <r00t4rd3d> myself im asking
[02:58:10] <Aero-Tec> but if your making thousands of one thing, trust me you will want to be able to speed it up as much as possible
[02:58:17] <ReadError> how often do you all lube your leadscrews ?
[02:58:35] <ctjctj> r00t4rd3d: there are lots of images on the net you can find and use. And emc can convert jpgs and other images to something that can be milled.
[02:58:55] <r00t4rd3d> i want to do inlays
[02:58:59] <ctjctj> But for most things you are going to want good 2d vector graphics which are harder to find.
[02:59:35] <ctjctj> in addition, if you are doing inlays you'll have to learn to make sure that you round corners correctly to let them inlay correctly.
[02:59:46] <ctjctj> Vectric has some great videos on lots of this stuff.
[03:00:04] <r00t4rd3d> I really need to finish my machine first
[03:00:11] <r00t4rd3d> my brain is over loaded with just that atm
[03:00:15] -!- demacus_ [[email protected]] has joined #linuxcnc
[03:00:20] <ReadError> finishing the machine is the easy part ;p
[03:00:30] <ReadError> the hard part for me was learning all the rest
[03:00:35] <r00t4rd3d> ctjctj, you have a pic of your machine?
[03:00:38] <ctjctj> ReadError: You got that right.
[03:00:55] <r00t4rd3d> well i am good with coding and computers/software/linux so....
[03:01:02] <Aero-Tec> your machine will have to be nice and rigid to do good inlays
[03:01:05] <ReadError> r00t4rd3d, i do linux all day
[03:01:11] <ReadError> but its like the machining part
[03:01:16] <r00t4rd3d> ive used linux for 20+ years
[03:01:23] <ReadError> thats my day job ;p
[03:01:26] <ReadError> linux sys admin
[03:01:32] <r00t4rd3d> bet thats fun
[03:01:34] <ReadError> although most of it is for web services not desktop
[03:01:46] <Aero-Tec> being a tad out this way or that is no problem if it is not mating up with a exact copy
[03:01:57] <r00t4rd3d> and by fun i mean royally suck
[03:02:25] <ctjctj> https://plus.google.com/u/0/110631207635469909107/posts/BQi4kd7PbH8
[03:02:39] <Aero-Tec> I to set up web servers using Linux
[03:02:55] <Aero-Tec> all remote terminal
[03:03:01] <ctjctj> 20 years of linux or 20 years of unix?
[03:03:06] <ReadError> yea i work for a hosting company
[03:03:14] <ReadError> my <3 is freebsd
[03:03:25] <ReadError> but we mostly use RHEL
[03:03:26] <ctjctj> ReadError: HIGH FIVE!!!
[03:03:37] <ctjctj> for freeBSD
[03:03:41] <ReadError> ;O
[03:04:09] <r00t4rd3d> i dont like any distro atm
[03:04:12] <ctjctj> I started using unix in 1982-1983 time frame.
[03:04:16] <r00t4rd3d> they all suck
[03:04:45] <r00t4rd3d> becoming to newb friendly
[03:05:13] <ReadError> i started with freebsd 4.2
[03:05:16] <r00t4rd3d> it was more fun to me when it was a challenge
[03:05:23] <ReadError> when i was a young buck at 13
[03:05:24] <r00t4rd3d> just to install
[03:06:05] <ctjctj> ReadError: about what year was that? I think my first FBSD was 1.4 or so.... Not sure.
[03:06:33] <ReadError> 2000 just checked
[03:06:34] <Aero-Tec> back when I was doing my server admin, redhat was king
[03:06:45] <ReadError> Aero-Tec, it still is really
[03:06:51] <ReadError> redhat enterprise linux
[03:07:09] <ctjctj> ReadError: *sigh* I suddenly feel VERY old.
[03:07:16] <Aero-Tec> lol
[03:07:25] <Aero-Tec> me to at times
[03:07:46] <ctjctj> I started programming "professionally" in 1976
[03:08:07] <Aero-Tec> still in school?
[03:08:12] <r00t4rd3d> mandrake was the first distro i used full time
[03:08:19] <ctjctj> yep.
[03:08:40] <ReadError> RHEL is pretty slick i must admit
[03:08:43] <ReadError> with yum
[03:08:47] <ReadError> no more rpm dep issues
[03:08:53] <ReadError> which was a huuuuge PITA
[03:09:05] <ReadError> 'yum update'
[03:09:09] <Aero-Tec> KimK: you around?
[03:09:10] <ReadError> bam, all the latest CVE updates
[03:09:38] <Aero-Tec> was hoping to find out what is wrong with my code
[03:10:52] <Aero-Tec> things are changing so quickly now days
[03:11:02] <ctjctj> ReadError: I've even got my name in the FreeBSD 3.0-RELEASE additional FreeBSD contributors page. which is sort of scary long time ago.
[03:11:10] <Aero-Tec> you have to be young to keep up
[03:11:28] <r00t4rd3d> non sense
[03:12:26] <r00t4rd3d> how old is linus?
[03:12:35] <r00t4rd3d> probably got us all beat
[03:13:10] <ctjctj> I'm older than him
[03:13:11] <Aero-Tec> I once found a error in a modarola processor, they had me talking to the guy that designed the chip to help work out the problem, that was fun
[03:13:17] <r00t4rd3d> he has got to be late 50's
[03:13:22] -!- factor has quit [Read error: Connection reset by peer]
[03:13:33] <r00t4rd3d> born December 28, 1969
[03:13:35] <r00t4rd3d> maybe not
[03:13:36] <ctjctj> Linus was born Dec 28, 1969
[03:14:02] <r00t4rd3d> 43
[03:14:14] <ctjctj> Aero-Tec: that's cool. I had a few conversations with the Woz back before there was an apple II. Neat guy.
[03:14:47] <ctjctj> They had a complete FP math system buried in the Apple II ROMs but basic only used integer math.
[03:15:03] <Aero-Tec> I had allot of fun with the old apple 2
[03:15:04] -!- factor [factor!~factor@r74-195-219-241.msk1cmtc02.mskgok.ok.dh.suddenlink.net] has joined #linuxcnc
[03:15:13] <Aero-Tec> and the COCO
[03:15:13] <ctjctj> Then the FP Basic came out and used their own FP routines which didn't run as fast or as accurately as the ROM versions.
[03:15:26] <ctjctj> Did you get to play with the KIM II?
[03:15:37] <Aero-Tec> no
[03:15:37] <ctjctj> Or the Poly Science boxes?
[03:15:58] <Aero-Tec> played with a Sinclare
[03:16:25] <ctjctj> We use to fix the home built PolySci boxes. Customers would buy kit boards for memory cards for S100 bus. Then we'd have to fix them.
[03:16:50] <ctjctj> It was like $500-$1000 for an 8K bytes (that's right 8192 bytes) of memory.
[03:16:57] <ctjctj> Yeah, the Sinclare came a little bit later.
[03:18:04] <Aero-Tec> and lets not forget the old commodores the 64 and 128
[03:18:10] <Aero-Tec> they were fun
[03:18:25] <ctjctj> KIM was a cool 6502 embedded board. had 1k of memory on it. 16 key hex key pad and a 8(?) digit LED display. Plus some IO ports. We used it to do a solar house embedded controller system.
[03:18:57] <ctjctj> Yep, the Commodore 64 with the chiclet keys.
[03:19:10] <Aero-Tec> sounds very much like the Sinclare
[03:19:31] <ctjctj> KIM was 6502 and I think the sinclare was 6900 or 8080 based?
[03:20:09] <ctjctj> Yeah, Z80 based.
[03:20:39] <Aero-Tec> yep
[03:20:56] <Aero-Tec> I have some of them around here somewhere
[03:21:55] <Aero-Tec> I should look, I may still have the Sinclare round here some where
[03:22:19] <ctjctj> 6502 was running at 1Mhz but was a pipeline design with one instruction completing per cycle. The 8080/Z80 was non-pipelined and took multiple cycles to do *anything* Plus 6502 was more risc based than the z80/8080. I use to have fun getting the 6502 do things faster than those over clockec z80s running at 5Mhz (normal was 4mhz)
[03:22:26] <Jymmm> Aero-Tec: Say What? you have SOME?! As in plural???
[03:23:28] <Aero-Tec> Z80 and 8080
[03:23:30] <Aero-Tec> yes
[03:23:47] <Aero-Tec> maybe even some 6502s as well
[03:23:53] <ctjctj> Neat thing about the 6502 was that it had an imcomplete set of extra registers that you could use. I wrote some code to that was "protected" by using the extra registers. They didn't decompile and unless you had analyzed the chip you wouldn't know what they did.
[03:24:06] <Jymmm> Aero-Tec: Shhhhhh, your age is showing again, cover that up ;)
[03:24:25] <Aero-Tec> I was a tec, did repair work so I had a whack of them around
[03:24:29] <ctjctj> Well, the registers were complete. You just couldn't do everything with them because some op codes were used for strange things.
[03:24:54] <Jymmm> Aero-Tec: I'm just teasing =)
[03:25:18] <Aero-Tec> lol
[03:25:22] <Aero-Tec> no problems
[03:25:28] <Aero-Tec> yes O am a old fart
[03:25:31] <Aero-Tec> I
[03:26:10] <Jymmm> Aero-Tec: Well hurry up and make that cnc controlled walker already before you forget how to !
[03:26:41] <Aero-Tec> good old assembly, I loved programming in assembly, lost art now days
[03:27:10] <ctjctj> *grins* must be why I like doing embedded code. Even if they mostly use C
[03:27:11] <Jymmm> so it software development
[03:27:25] <ctjctj> Jymmm: that is just sad.
[03:27:33] <Jymmm> that's why there's 17,000 versions
[03:27:46] <Jymmm> 12.025.774
[03:28:22] <ctjctj> but I'm off. Likely be back tomorrow with other memory dumps and begging for help with gcode
[03:28:26] <Aero-Tec> I was thinking I should make a cool wild chair for when I get old
[03:28:43] <Jymmm> you ever notice that FF jumped from v9.0 to v10.0 to v11.0 to v12.0 ???
[03:29:07] <Aero-Tec> whats FF?
[03:29:29] <Jymmm> Aero-Tec: with self tracking so you just push one button and takes you home when our drunk
[03:29:37] <Jymmm> FF == Fire Fox
[03:29:55] <Jymmm> the web browser
[03:30:05] <Aero-Tec> I use fire fox
[03:30:25] <Aero-Tec> thought we were still talking programming language
[03:30:45] <ReadError> Jymmm, dont forget 4
[03:31:00] <ReadError> wasnt there a big jump after 4?
[03:31:24] <Jymmm> we are, I'm saying that devleopers today dont write good code, they just say "will get it in the next version" but FF has jumped MAJOR VERSIONS in the last year.
[03:31:36] <alex4nder> hey
[03:32:01] <Jymmm> no 11.2 or 11.5, straight from v11.0 to v12.0
[03:32:02] <Aero-Tec> KimK: you around?
[03:33:12] <Jymmm> Aero-Tec: make sure that the padign on your chair can be tossed in the washer and that the stuff that makes it run is IPX7 rated for water and dust proof!
[03:33:16] <Jymmm> padding
[03:33:50] <Jymmm> then you can just hose that sucker off any time!
[03:34:38] -!- sumpfralle has quit [Quit: Leaving.]
[03:34:42] <Jymmm> leave room for accessories too, you never know what they'll have available in the future, maybe hovercraft packs
[03:37:25] <Aero-Tec> lol
[03:37:35] <Aero-Tec> love hover craft
[03:37:43] <alex4nder> anyone have a recommendation on a coolant sump pump?
[03:37:49] <Aero-Tec> not good for stairs
[03:38:29] <ReadError> alex4nder, what cam software do you use?
[03:38:33] <ReadError> to convert stl-> gcode
[03:38:47] <alex4nder> that depends on what I'm doing
[03:38:51] <alex4nder> usually I don't do that.
[03:39:01] <ReadError> http://i.imgur.com/8xavv.png
[03:39:04] -!- mozmck has quit [Quit: Leaving.]
[03:39:09] <ReadError> pycam messes it up ;/
[03:39:20] <alex4nder> yah, I definitely wouldn't do that with STL.
[03:39:25] <alex4nder> I'd program that manually.
[03:39:37] <jdhNC> I'd drop it in cut2d and be done in 30 seconds
[03:39:54] <alex4nder> or that
[03:40:57] <ReadError> payware ;(
[03:41:03] <ReadError> is the demo full feature?
[03:41:07] <alex4nder> write the g-code yourself
[03:41:09] <alex4nder> it's easy
[03:41:27] <alex4nder> and you should learn how all that stuff works anyway
[03:41:37] <Jymmm> Aero-Tec: And whatever you do, make sure you allow for this... http://vimeo.com/31008456
[03:41:40] <ReadError> i just learned a bit of solid works today ;/
[03:41:46] <jdhNC> demo doesn't save gcode except for the demos. I bought a copy
[03:41:52] <ReadError> solidworks was very intuitive
[03:41:59] <ReadError> unlike many of the other apps
[03:42:04] <ReadError> which have a steep learning curve
[03:42:13] <jdhNC> I've never found any cad program to be intuitive
[03:42:24] <ReadError> solidworks really is
[03:42:26] <ReadError> it felt natural
[03:42:31] <ReadError> and doing what i wanted was easy
[03:43:07] <Aero-Tec> Jymmm: cool toy but not good on land. lol
[03:43:25] <alex4nder> ReadError: Looking at your drawing, I see a 180 degree arc, a 360 degree arc, a 30 degree arc (?) and 8 peckdrills
[03:43:31] <Aero-Tec> yes solid works is great, that is what I use
[03:43:33] <alex4nder> er 2 30degree arcs
[03:43:36] <jdhNC> I ran across some software this week that was even more non-intuitive. Survey software for a cesium magnetometer (boat towed)
[03:43:40] <Jymmm> Aero-Tec: Sure it is, just add water!
[03:44:30] <Jymmm> Aero-Tec: if you were wondering.... $98,000 USD
[03:44:42] <Aero-Tec> is that all
[03:45:06] <Aero-Tec> some guy made a conversion for his jet ski
[03:45:11] <Aero-Tec> worked well
[03:45:21] <Jymmm> Aero-Tec: Yep! But if you go out to havasu, you can get an hours or so for about $400, that includes training
[03:45:24] <Aero-Tec> much cheaper way to go
[03:45:51] <Aero-Tec> have you tried it yet?
[03:46:10] <Jymmm> I wish, I'd pay the $400 gladly
[03:46:28] <Jymmm> It's a once in a lifetime thing
[03:46:38] <Aero-Tec> make one
[03:47:00] <Jymmm> Nah, wouldn't use it more than once, $400 is cheaper
[03:47:01] <Aero-Tec> find a friend with a jetski and make a adapter
[03:47:28] <Aero-Tec> one hour would not be enough
[03:47:42] <Aero-Tec> would want to play longer with it
[03:47:55] <Aero-Tec> wonder what the second hour would cost
[03:48:05] <Aero-Tec> no training needed
[03:52:43] <Aero-Tec> I am off to bed soon
[03:52:58] <Aero-Tec> still feeling lousy
[03:57:13] <Aero-Tec> night all
[04:01:26] -!- Thetawaves has quit [Quit: This computer has gone to sleep]
[04:13:22] -!- mk0 [[email protected]] has joined #linuxcnc
[04:21:21] -!- skunkworks__ [skunkworks__!~chatzilla@str-bb-cable-south-3-102.dsl.airstreamcomm.net] has joined #linuxcnc
[04:22:22] <Connor_CNC> is there a mod function for hal ?
[04:26:15] <jdhNC> there is in ladder
[04:26:56] <skunkworks__> Connor_CNC: the next time andy_pough is here - ask him about virtual index... I think he had done it.
[04:38:12] -!- capricorn_one [[email protected]] has joined #linuxcnc
[04:42:13] <Connor_CNC> skunkworks_ okay, he won't be back till next Monday,.. I think I saw h e was away for the weekend
[04:47:39] -!- FinboySlick has quit [Quit: Leaving.]
[04:50:45] -!- cmorley has quit [Ping timeout: 260 seconds]
[04:54:48] -!- skunkworks__ has quit [Remote host closed the connection]
[04:59:26] -!- psha[work] [psha[work][email protected]] has joined #linuxcnc
[05:04:28] -!- Fox_Muldr has quit [Ping timeout: 265 seconds]
[05:05:48] -!- Fox_Muldr [[email protected]] has joined #linuxcnc
[05:08:45] <Connor> trying to find some good pictures of people limit switches installed...
[05:10:06] <r00t4rd3d> what controller do you have
[05:11:00] <Connor> huh?
[05:11:17] <r00t4rd3d> like a gecko or tb6560
[05:11:28] <Connor> Keling 5056
[05:12:15] <roycroft> have you tried going to images.google.com and typing "limit switch installation"?
[05:12:28] <r00t4rd3d> or youtube
[05:12:30] <Connor> looking on the cnczone right now..
[05:12:41] <r00t4rd3d> ive learned alot from youtube
[05:12:43] * roycroft notes the non-answer
[05:13:01] <Connor> but, yes, I've done goggle search too
[05:13:21] <roycroft> i just went to the google images site, typed that in, and got heaps of useful results
[05:14:09] <roycroft> but i don't know exactly what you're trying to learn from the images you're seeking, so perhaps that is not the most useful query for you
[05:14:25] <r00t4rd3d> finding someone alive on irc who has done it though is that much better
[05:14:45] <roycroft> generally, yes
[05:14:50] <Connor> I have a slew of micro switches, all wither levers.. non with rollers..
[05:15:26] <Connor> trying to see if anyone has used non roller kind.. planning on one switch for X and one for Y (center mounted)
[05:16:13] <Jymmm> Connor: WTH?! It's LIMIT switch, not CENTER switch.
[05:17:12] <Connor> Jymmm: You put switch in middle.. You put stops on either end.. and your done. ??
[05:17:29] <Jymmm> again, it's LIMIT
[05:17:52] <Jymmm> you have reached the limit, the end, there is no more.
[05:18:15] <roycroft> right - you put two switches on each axis
[05:18:36] <Jymmm> If you want a HOME switch in the middel, so be it.
[05:18:38] <Jymmm> middle
[05:19:03] <roycroft> you use all nc switches, and connect them in series
[05:19:21] <roycroft> if ever that circuit opens, you stop
[05:19:26] <Connor> Yes, I know all that.. WTF does it matter were the switch is at as long as it trips at the end of the travel ?
[05:19:57] <Jymmm> key word, END, not MIDDLE.
[05:20:00] <roycroft> a dp switch could work
[05:20:00] <Connor> We're talking a Mill, not a router..
[05:20:13] <roycroft> center closed
[05:20:16] <roycroft> left or right open
[05:20:20] <Connor> http://www.micro-machine-shop.com/RF_power_feed_limit_switch.jpg
[05:20:25] <Connor> example image.
[05:20:26] <roycroft> you could do that with one switch on each axisw
[05:21:02] -!- cmorley has quit [Ping timeout: 260 seconds]
[05:21:08] <roycroft> ok, that's a kind of nc dp switch
[05:21:30] <Connor> Is a micro or optical sensor in there.. and gets tripped in either direction.
[05:21:49] <Connor> http://media.digikey.com/photos/CK%20Comp%20Photos/11TL604,%2011TL602.jpg
[05:21:52] <roycroft> so that's what you have?
[05:22:12] <Connor> No. I just have a micro.. but I can make a enclosure.
[05:22:36] <roycroft> two switches in the enclosure, one facing right and one facing left?
[05:24:13] <Connor> No, just one. I guess I need to get some ones with rollers.. or bend the lever rounded..
[05:25:08] -!- cmorley1 has quit [Ping timeout: 240 seconds]
[05:38:52] -!- AdrianG [AdrianG!~amphetami@unaffiliated/amphetamine] has joined #linuxcnc
[05:51:24] -!- Thetawaves [[email protected]] has joined #linuxcnc
[05:57:46] -!- AdrianG [AdrianG!~amphetami@unaffiliated/amphetamine] has parted #linuxcnc
[06:19:11] <alex4nder> hey
[07:31:30] -!- vladimirek [[email protected]] has joined #linuxcnc
[07:32:58] -!- asdfasd [[email protected]] has joined #linuxcnc
[07:37:59] -!- DJ9DJ [DJ9DJ!~Deejay@unaffiliated/dj9dj] has joined #linuxcnc
[07:39:17] <DJ9DJ> moin
[07:40:34] -!- vladimirek has quit [Remote host closed the connection]
[07:56:44] -!- bedah [[email protected]] has joined #linuxcnc
[07:56:44] -!- dimas has quit [Read error: Connection reset by peer]
[07:57:29] -!- dimas [[email protected]] has joined #linuxcnc
[08:28:57] -!- fliebel [[email protected]] has joined #linuxcnc
[08:45:26] -!- H264 has quit [Read error: Connection reset by peer]
[08:45:47] -!- H264 [[email protected]] has joined #linuxcnc
[09:03:08] -!- rob_h [[email protected]] has joined #linuxcnc
[09:29:15] -!- sumpfralle [[email protected]] has joined #linuxcnc
[09:41:18] H264 is now known as WalterN
[09:44:55] -!- mk0 has quit [Quit: Leaving]
[09:54:21] -!- Tectu [[email protected]] has joined #linuxcnc
[09:54:38] <Tectu> here you go guys: http://www.youtube.com/watch?v=k7T9jM97geY
[09:58:31] cylly2 is now known as Loetmichel
[09:59:16] <Loetmichel> mornin'
[09:59:22] <alex4nder> sup Loetmichel
[10:01:38] <alex4nder> Tectu: nice
[10:02:46] <Loetmichel> Tectu: hmmm
[10:03:03] <Loetmichel> a bit much material for a reprap?
[10:03:27] <Loetmichel> but: nice construction!
[10:10:48] <alex4nder> so .. I made my own oil-based coolant
[10:10:55] <alex4nder> I'm wondering how well this is going to work.
[10:15:10] <Thetawaves> canola oil has been working well for me
[10:15:41] <alex4nder> you flooding your mill with it?
[10:15:52] <Thetawaves> i'll try peanut oil next, but it is more expensive
[10:15:55] <Thetawaves> yeah, flood
[10:16:00] <alex4nder> nice
[10:16:06] <alex4nder> any bacteria problems?
[10:16:23] <Thetawaves> none, there is no water in the mix.
[10:17:04] <Thetawaves> it made my cuts burr free
[10:17:09] <Thetawaves> it was amazing.
[10:17:47] <Thetawaves> i think the burs are mostly chips cold welding to the material behind the cutter, the oil flushes it away
[10:18:22] <alex4nder> what kind of pump are you using?
[10:18:37] <Thetawaves> a simple 300gph pond pump
[10:18:42] <alex4nder> nice
[10:18:43] <Thetawaves> because i already had it
[10:19:02] <Thetawaves> it pumps oil pretty well if you have a pig enough hose on the output
[10:19:07] <Thetawaves> big*
[10:19:30] <Thetawaves> for the same price you can get a positive displacement pump that will really pump oil at walmart
[10:20:08] <Thetawaves> if money is involved, definitely get the positive displacement pump
[10:20:48] <alex4nder> yah, the pond pumps I saw had a lot of bypass under any real restriction
[10:22:09] <Thetawaves> i use cooking oil because my machine is in my dining room... just feels a whole lot safer
[10:22:27] <Thetawaves> not because i need cheap oil or think it's superior cutting fluid
[10:23:18] <alex4nder> right. which machine?
[10:23:46] <Thetawaves> 3020T engraving machine
[10:23:50] -!- Geissler [[email protected]] has joined #linuxcnc
[10:24:17] <alex4nder> ah cpp;
[10:24:20] <alex4nder> er cool
[10:24:34] <alex4nder> nice and small
[10:24:52] <alex4nder> what're you doing with it?
[10:25:22] <Thetawaves> engraving... i made some designs in plate aluminum
[10:25:35] <Thetawaves> and circuit boards, lots of circuit boards
[10:25:45] <alex4nder> nice
[10:26:37] <Thetawaves> i am in the process of upgrading from 200w to 300w spindle motor
[10:26:46] <Thetawaves> :D
[10:28:01] <Thetawaves> i can fit 1/4" endmills in that thing
[10:29:56] <Thetawaves> so sorry alex4nder, what did you make your fluid out of?
[10:31:56] <alex4nder> the mix I'm going to test tomorrow is: water, mineral oil, tide ultra laundry detergent, and redline water wetter
[10:32:24] <Thetawaves> scary
[10:32:33] <Thetawaves> i was researching home made cutting fluid on google
[10:32:54] <jthornton> what are you cutting?
[10:33:03] <Thetawaves> and one of the main results was a cdc report about how this machinist got flesh eating bacteria in his hand while changing the cutting fluid
[10:33:06] <alex4nder> aluminum and steel
[10:33:32] <jthornton> for aluminum you just need some water with dish soap in it
[10:34:00] <Thetawaves> what about your machine tools?
[10:34:02] <alex4nder> jthornton: that's basically what this is
[10:34:38] <alex4nder> the mineral oil and water wetter are there to counter act rust and corrosion
[10:34:39] <jthornton> what is the mineral oil for?
[10:34:45] <jthornton> ah ok
[10:35:57] <jthornton> I use sodium nitrite in my plasma water to stop any corrosion
[10:36:18] <alex4nder> Thetawaves: you can get flesh eat bacteria from a spider bite.
[10:36:34] <Thetawaves> flesh eating bacteria is very rare.
[10:39:36] <Thetawaves> ok my mistake
[10:39:38] <Thetawaves> "Flesh-eating bacteria" is a misnomer, as the bacteria do not actually "eat" the tissue. They cause the destruction of skin and muscle by releasing toxins (virulence factors), which include streptococcal pyogenic exotoxins. S. pyogenes produces an exotoxin known as a superantigen. This toxin is capable of activating T-cells non-specifically, which causes the overproduction of cytokines and severe systemic illness (Toxic shock syndrome).
[10:39:59] <Thetawaves> and there are a few families of bacteria capable of this
[10:40:24] <Thetawaves> apparently the infection is the really rare part
[10:41:17] <jthornton> we have billions of brown recluse spiders that have a hemotoxin venom
[10:42:33] <Thetawaves> HAHA
[10:42:34] <Thetawaves> Jeff Hanneman, guitarist for the thrash-metal band Slayer, contracted the disease in early 2011. He was allegedly infected after being bitten by a spider.[22]
[10:42:47] * Thetawaves firmly places foot in mouth
[10:44:02] <TekniQue> 10:33:03 < Thetawaves> and one of the main results was a cdc report about how this machinist got flesh eating bacteria in his hand while changing the cutting fluid
[10:44:06] <TekniQue> yikes
[10:47:04] <Thetawaves> yeah
[10:47:11] <Thetawaves> like i said, scary
[10:47:19] <Thetawaves> gnight fellas
[10:47:20] -!- Thetawaves has quit [Quit: This computer has gone to sleep]
[10:47:52] <jthornton> night
[10:48:08] <jthornton> does xchat have a time stamp feature?
[10:48:29] <TekniQue> yes
[10:48:53] * jthornton tries again to find out how to turn it on
[10:50:34] <jthornton> the only thing I can find is for the logs, when I used to use chatzilla it had the time in the messages
[11:00:10] <archivist> interface->text box->time stamps
[11:00:16] <jthornton> dang I finally found it
[11:00:29] <jthornton> thanks archivist
[11:01:16] -!- H264 [[email protected]] has joined #linuxcnc
[11:04:24] -!- WalterN has quit [Ping timeout: 250 seconds]
[11:13:07] -!- JT-Shop has quit [Quit: Leaving]
[11:30:28] <jthornton> archivist, got a minute to review something for me?
[11:30:47] <archivist> sure
[11:30:52] <jthornton> http://gnipsel.com/shop/emc2/gcode.xhtml
[11:31:03] <jthornton> just a couple of pages I started the other day
[11:32:43] <archivist> in http://gnipsel.com/shop/emc2/tutorial/tut01.html "preamble that might be different" "preamble that might be in a different"
[11:33:39] <archivist> next section user decides dia/radius
[11:34:53] <archivist> devations-deviations
[11:35:43] <jthornton> opps forgot to run spell checker
[11:39:07] <archivist> arc diagrams dont match
[11:40:28] <jthornton> I see that now lol
[11:42:29] -!- demacus [[email protected]] has joined #linuxcnc
[11:45:09] -!- demacus_ has quit [Ping timeout: 265 seconds]
[11:45:22] <archivist> you got the doc building going then!
[11:45:49] <jthornton> yea, a guy from the asciidoc google groups sorted me out
[12:15:35] <archivist> needs some navigation too
[12:15:48] -!- IchGuckLive [[email protected]] has joined #linuxcnc
[12:15:58] <jthornton> yea, I've not got that far yet
[12:16:22] <IchGuckLive> hi all i finished my casel today with stone optics from foamcut http://mechmo.de/styrocat.html
[12:16:22] <jthornton> best would be to copy the linuxcnc index somehow
[12:22:06] <jthornton> IchGuckLive, pretty damm slick!
[12:25:45] -!- demacus_ [[email protected]] has joined #linuxcnc
[12:29:56] -!- demacus has quit [Ping timeout: 272 seconds]
[12:38:23] -!- isssy [[email protected]] has joined #linuxcnc
[12:41:33] -!- IchGuckLive [[email protected]] has parted #linuxcnc
[12:54:30] <jthornton> well crap Xchat for winblows is $20 if you use more than 30 days
[13:00:42] -!- isssy has quit [Quit: Bye Bye]
[13:00:58] <bedah> silverex is free windows xchat
[13:04:41] <archivist> jthornton, there is a fork of xchat called....ychat be very careful which ychat you get
[13:06:07] -!- mozmck [mozmck!~moses@client-74.117.92.175.dfwtx.partnershipbroadband.com] has joined #linuxcnc
[13:06:54] <archivist> is silverex renamed ychat :)
[13:08:16] -!- psha[work] has quit [Quit: Lost terminal]
[13:09:49] -!- syyl [[email protected]] has joined #linuxcnc
[13:13:17] <Geissler> jthornton, use crack for xchat? Or use ychat - it's free
[13:16:11] -!- X704 has quit [Read error: Connection reset by peer]
[13:16:28] -!- WalterN [[email protected]] has joined #linuxcnc
[13:16:44] -!- X704 [[email protected]] has joined #linuxcnc
[13:20:25] -!- H264 has quit [Ping timeout: 276 seconds]
[13:32:01] <jdhNC> Center format arcs are more accurate than radius format arcs
[13:32:05] <jdhNC> Why is that?
[13:35:56] <ctjctj> jdhNC: Because you state explicitly the points where you want the arc to end.
[13:36:12] <ctjctj> jdhNC: whereas the other is a calculated end point.
[13:37:10] <jdhNC> ok, so the end point is more accurate, doesn't that make the radius less accurate?
[13:37:34] <ctjctj> Not really.
[13:38:02] <jdhNC> why not, the center of the arc radius is calculated.
[13:38:40] <ctjctj> Do you care if the center of the arc is off by 1/1000 in a 2 inch circle?
[13:38:52] <ctjctj> Not really, you care where the cutter runs.
[13:39:39] <jdhNC> guess I'd have to see the actual error to know if I cared.
[13:40:35] <ctjctj> They are different types of calculations is the best answer I can give. I'd have to go dig into the math a little more in order to answer better. But the gist is that using angles isn't as accurate.
[13:41:29] <ctjctj> If your angle is off by 1/1000 and your radius is 10 inches then your final point is going to be off by 1/1000 * 10 or 1/100.
[13:41:44] <jdhNC> why would your angle be off at all?
[13:42:04] <ctjctj> because you are using floating point numbers going in to sin/cos functions.
[13:43:07] <jdhNC> bah, computers are perfect!
[13:43:17] <freespace> best lie we have ever told
[13:43:19] <jdhNC> for some approximation of perfect.
[13:43:55] -!- Geissler has quit [Ping timeout: 264 seconds]
[13:44:16] -!- Geissler [[email protected]] has joined #linuxcnc
[13:45:34] <ctjctj> The issue is the multiplication affect. Every point you define is off by a value less than epsilon. You can make epsilon as small as you want but the smaller it gets the harder it is to do. But anytime you can multiply epsilon your error gets that much bigger. :-(
[13:46:02] <jdhNC> I understand the math, not not sure how much it matters.
[13:51:22] -!- toastydeath has quit [Read error: Connection reset by peer]
[13:51:35] -!- toastydeath [[email protected]] has joined #linuxcnc
[14:08:33] -!- psha [[email protected]] has joined #linuxcnc
[14:35:51] -!- skunkKandT [[email protected]] has joined #linuxcnc
[14:40:37] <skunkKandT> logger[psha]:
[14:49:32] -!- syyl_ [[email protected]] has joined #linuxcnc
[14:53:22] -!- syyl has quit [Ping timeout: 276 seconds]
[14:53:44] -!- Tom_L [[email protected]] has joined #linuxcnc
[14:54:10] Tom_L is now known as Guest63168
[14:54:55] -!- Guest63168 has quit [Client Quit]
[15:01:38] -!- Tom_afk [[email protected]] has joined #linuxcnc
[15:01:55] -!- Tom_afk [[email protected]] has parted #linuxcnc
[15:47:49] -!- ve7it [[email protected]] has joined #linuxcnc
[16:09:41] <Jymmm> jdhNC: Say yo had a level, and it was off by 100th of a degree. Now, you're building a cider block wall and you use that level to make sure the wall is perfectly straight. When you build up the wall to 30 some-odd feet, it's gonna be tilted out.
[16:11:31] <Jymmm> ...as the errors are cumulative.
[16:11:36] <archivist> there is a chance you reverse the level so it should average out straight
[16:12:18] <archivist> but no one uses a level without checking it do they
[16:12:40] <Jymmm> True, especially if you happen to know that is exactly how you check the accuracy of a level, most don't =)
[16:14:59] -!- ktchk [[email protected]] has joined #linuxcnc
[16:23:18] <Jymmm> 220VAC RED LED Panel lights (22mm) http://www.dealextreme.com/p/22mm-led-power-indicator-signal-lights-red-ac-220v-130360
[16:33:21] <Jymmm> IDEC Control illuminated Button http://www.dealextreme.com/p/red-indicator-light-engine-push-start-button-set-for-auto-refitting-dc-12v-24560 and it looks liek the contact are also rated for 120V http://www.alliedelec.com/search/productdetail.aspx?sku=70172633#tab=specs
[16:35:26] <Jymmm> And in Blue http://www.dealextreme.com/p/blue-indicator-light-engine-push-start-button-set-for-auto-refitting-dc-12v-24561
[16:37:36] -!- syyl_ws [[email protected]] has joined #linuxcnc
[16:38:45] -!- stealthzap has quit [Read error: Connection reset by peer]
[16:40:12] -!- stealthzap [[email protected]] has joined #linuxcnc
[16:40:14] <alex4nder> hey
[16:42:29] -!- WillenCMD [WillenCMD!451dd9a7@gateway/web/freenode/ip.69.29.217.167] has joined #linuxcnc
[16:42:43] -!- Geissler has quit [Ping timeout: 264 seconds]
[16:43:44] <Jymmm> ve7it: LOL, The worlds skinnyest dummy load... http://www.dealextreme.com/p/100w-high-gain-antenna-vhf-uhf-117735
[16:45:05] <Jymmm> ve7it: I just don't see where you add the mineral oil =)
[16:46:06] -!- Vq has quit [Ping timeout: 246 seconds]
[16:47:00] -!- Vq [[email protected]] has joined #linuxcnc
[16:47:01] -!- Geissler [[email protected]] has joined #linuxcnc
[16:47:09] <TekniQue> lol 100 watts on that thing would probably result in some amounts of smoke
[16:47:25] <Jymmm> TekniQue: Yeah, in the radio =)
[16:47:56] <TekniQue> yes, 95% standing wave ratio
[16:48:01] <TekniQue> boom
[16:48:35] <Jymmm> I dont know about 'boom', but I suspect a lot of snap crackle and pop
[16:49:21] <Jymmm> TekniQue: and who in the hell uses a 14" antenna with a PL259 connector?!
[16:49:30] <Jymmm> on 2m/440
[16:51:03] <Jymmm> TekniQue: you a ham?
[16:51:12] <TekniQue> nope
[16:51:19] <Jymmm> ah, ok
[16:51:27] <TekniQue> but I have a VHF radio
[16:51:42] <TekniQue> Yaesu 65 watt programmable
[16:51:42] <Jymmm> FRS ?
[16:51:47] <Jymmm> ah, cool
[16:52:03] <Jymmm> yaesu what?
[16:53:01] <TekniQue> I don't remember
[16:53:04] <TekniQue> it's a car radio
[16:53:14] <Jymmm> I figured that =)
[16:53:21] <Jymmm> (@ 65W)
[16:53:32] <TekniQue> I have a handheld also
[16:54:44] <Jymmm> Yeah, I want to mod my HT, just haven't gotten around to doing it yet
[16:55:23] <Jymmm> as then I need to reprogram it all over again.
[16:58:36] <TekniQue> I modded both of mine to transmit on any frequency
[16:58:48] <TekniQue> I have a few licensed channels
[16:58:59] -!- lerman has quit [Remote host closed the connection]
[16:59:17] <Jymmm> I've opened my mobile rig, just haven't done the HT yet.
[16:59:17] <TekniQue> but as they come from the factory they can only transmit on a narrow range of frequencies
[16:59:44] <Jymmm> what do you use them for?
[17:00:05] <TekniQue> chatting with my mates when travelling
[17:00:26] <Jymmm> ah
[17:00:47] <TekniQue> in offroad trucks
[17:01:13] <Jymmm> gotcha
[17:04:12] -!- lerman [[email protected]] has joined #linuxcnc
[17:10:42] -!- IchGuckLive [[email protected]] has joined #linuxcnc
[17:13:19] -!- Geissler has quit [Ping timeout: 264 seconds]
[17:16:03] -!- ve7it has quit [Remote host closed the connection]
[17:16:35] -!- FinboySlick [[email protected]] has joined #linuxcnc
[17:22:38] <Jymmm> jthornton: no pun intended http://mykitchenapron.blogspot.com/2011/08/white-trash-dip.html
[17:27:38] -!- Geissler [[email protected]] has joined #linuxcnc
[17:28:31] -!- Geissler has quit [Client Quit]
[17:28:37] -!- mk0 [[email protected]] has joined #linuxcnc
[17:34:40] -!- ktchk [[email protected]] has parted #linuxcnc
[17:47:40] -!- gambakufu has quit [Ping timeout: 244 seconds]
[17:49:38] -!- asdfasd has quit [Ping timeout: 245 seconds]
[18:17:44] -!- pieman100 [[email protected]] has joined #linuxcnc
[18:32:13] -!- IchGuckLive has quit [Quit: ChatZilla 0.9.87 [Firefox 11.0/20120310193829]]
[18:32:50] -!- sumpfralle has quit [Quit: Leaving.]
[18:34:22] -!- gambakufu [[email protected]] has joined #linuxcnc
[18:42:36] -!- pcw_home has quit [Quit: ChatZilla 0.9.88.2 [Firefox 11.0/20120224155307]]
[18:58:09] -!- Thetawaves [[email protected]] has joined #linuxcnc
[19:03:45] -!- SolarNRG [[email protected]] has joined #linuxcnc
[19:03:48] <SolarNRG> Hi guys
[19:03:56] <SolarNRG> Does anybody in here have a working induction melter?
[19:07:08] -!- pieman100 has quit [Quit: Leaving]
[19:23:01] <Jymmm> hahaha
[19:24:33] <SolarNRG> Why is that funny?
[19:24:52] -!- petteri_ [[email protected]] has joined #linuxcnc
[19:25:46] <Jymmm> Cause you were working on microwaves till I showed you that video =)
[19:26:48] -!- psha has quit [Quit: Lost terminal]
[19:27:36] <SolarNRG> I've now done 9 microwave experiments
[19:27:40] <SolarNRG> And I've lit a cigarette
[19:27:47] <SolarNRG> I faied to melt zinc, let alone ally
[19:27:54] <SolarNRG> even after hours of cooking
[19:28:14] <Jymmm> try solder as it has the lowest melting point I know of
[19:28:14] <SolarNRG> I'm giving up on the microwave idea, I'm sure there is a way to do it, now I'm going into induction
[19:28:21] <archivist> does the microwave still heat water
[19:28:24] <SolarNRG> I can do solder with a soldering iron
[19:28:25] <SolarNRG> Yes
[19:28:27] <SolarNRG> It does
[19:28:59] <Jymmm> if you cant melt solder with a microwave, your not going to melt any other metals that I'm aware of
[19:29:32] <alex_joni> Jymmm: there are lower melting temperatures than solder
[19:29:39] <SolarNRG> OK FORGET microwave.... I have really tried
[19:29:45] <Jymmm> as far as induction goes, your cheapest bet is a replacment element from an induction cooktop
[19:29:55] <archivist> try woods metal
[19:29:56] <alex_joni> I had some alloys which melted around 50-60C
[19:30:01] <Jymmm> for testing that is
[19:30:09] <archivist> http://en.wikipedia.org/wiki/Wood%27s_metal
[19:30:13] <SolarNRG> This was my last test http://www.youtube.com/watch?v=KuWEUnxG1SE
[19:30:14] <Jymmm> alex_joni: in a microwave?
[19:30:20] <SolarNRG> Fields metal
[19:30:25] <archivist> see table at bottom
[19:30:29] <alex_joni> Jymmm: no, in water
[19:30:49] <alex_joni> archivist: that's it :)
[19:31:02] <alex_joni> or something like that
[19:31:05] <archivist> they did a candid camera in a cafe with spoons made of it
[19:31:09] <ReadError> jeeeezee
[19:31:11] <SolarNRG> I have failed to do it by way of a microwave
[19:31:15] <alex_joni> right, I tried that too :))
[19:31:16] <ReadError> i didnt think creating a toolpath would be so difficult
[19:31:37] <SolarNRG> I now wish to listen to your advice and do it with an induction loop. I wanted to know if anyone here lives in the UK and has built one and I could paypal him to make me one for me
[19:31:39] <alex_joni> Jymmm: I used to that extract many pin DIPs
[19:31:47] <SolarNRG> Big enough for a medium crucible to fit in
[19:31:54] <Jymmm> alex_joni: ah
[19:31:57] <alex_joni> you can mix it with the existing solder, and just lift the DIP out
[19:32:05] <SolarNRG> I'd like to be able to melt a couple of litres of steel at once
[19:32:11] <archivist> SolarNRG, hehe...can you get enough current from the mains
[19:32:13] <alex_joni> the pins stay warm for a while, so it stays liquid
[19:32:41] -!- gambakufu has quit [Ping timeout: 260 seconds]
[19:33:28] <archivist> Im in the uk I want your money BUT think of the costs and practicalities
[19:34:33] -!- petteri_ has quit [Remote host closed the connection]
[19:34:34] -!- Roguish [[email protected]] has joined #linuxcnc
[19:37:22] <SolarNRG> Well i MUST do this outside
[19:37:25] <SolarNRG> safety first
[19:37:32] <SolarNRG> My extension lead can only handle 2.4kw
[19:37:41] <SolarNRG> I am using a domestic socket
[19:37:57] <SolarNRG> I think the most amount of amps I could extract would be 13amps@240v
[19:38:07] -!- gambakufu [[email protected]] has joined #linuxcnc
[19:38:13] <archivist> not going to cut it
[19:38:22] <Jymmm> maybe melt a coat hanger
[19:38:32] <SolarNRG> With a rectifier and inverter that goes to 20khz
[19:38:38] <archivist> please adjust your dreams to include reality
[19:38:46] <Jymmm> archivist: Awwwwwwwwwwww
[19:39:00] <SolarNRG> Have a look at this kids: http://www.youtube.com/watch?v=2kuJ-FZBnok&feature=related
[19:39:10] <SolarNRG> His is only 150w
[19:39:17] <SolarNRG> He can heat up a nail
[19:39:33] <alex_joni> http://home.c2i.net/metaphor/mvpage.html
[19:39:36] <Jymmm> archivist: "No thanks, I'll just create my own reality instead! =)"
[19:39:39] -!- DJ9DJ_ [DJ9DJ_!~Deejay@unaffiliated/dj9dj] has joined #linuxcnc
[19:40:13] <SolarNRG> alex, I did all that with the molochite, magnetite, graphite, I actually did it and I have a video of it
[19:40:18] -!- DJ9DJ has quit [Disconnected by services]
[19:40:22] DJ9DJ_ is now known as DJ9DJ
[19:40:46] <SolarNRG> http://www.youtube.com/watch?v=uh1VDGP86SY
[19:41:37] <SolarNRG> ^^ This was my magnetite test
[19:41:57] <SolarNRG> It got hot enough to singe rizla paper but not hot enough to melt metal
[19:43:53] <SolarNRG> I'm either doing something wrong or this guide is simply false information
[19:44:07] <SolarNRG> I'm losing faith in melting metals in a microwave oven
[19:44:11] -!- dimas_ has quit [Ping timeout: 252 seconds]
[19:44:18] <SolarNRG> I'm now thinking of the induction loop method
[19:46:53] <archivist> note this is 15kw
[19:46:57] <archivist> http://www.youtube.com/watch?v=k4xsqw463Hs&feature=endscreen&NR=1
[19:49:03] <SolarNRG> How is he not getting electrocuted?
[19:49:12] <Jymmm> whoa... cold enough to touch instantly, nice.
[19:49:18] <SolarNRG> Is it because the frequency is so high?
[19:50:38] <Jymmm> SolarNRG: Maybe you should read a bit about what your attempting to accomplish http://en.wikipedia.org/wiki/Induction_heating
[19:51:21] <mk0> Jymmm, finally! someone told it
[19:51:49] <Jymmm> mk0: I call em as I see em is all.
[19:53:20] <mk0> even our institute has 100 y.o. induction melting furnaces
[19:54:00] <Jymmm> mk0: That's kinda cool that 100yo gear is STILL working =)
[19:54:11] <SolarNRG> Can I switch off my fusebox, and hook up said system to my cooker wires at the back of my oven?
[19:54:32] <mk0> well i'm just joking that our equipment is so out of date, that i grind my teeth
[19:55:12] <Jymmm> mk0: Oh, heh. I thought a 100yo furnance was built so well that it survived all this time.
[19:55:28] <SolarNRG> Surely my cooker electric will allow higher current
[19:55:32] <SolarNRG> than a socket
[19:55:32] <mk0> and f...ing YES, it's from 60-s and stiill working
[19:55:46] <archivist> I drive a steam engine made in 1849
[19:55:56] <mk0> :D
[19:56:16] <Jymmm> mk0: Hell there are hippis/CEO's from the 60's still around for that matter =)
[19:56:27] <mk0> YES!!!!!
[19:56:41] <Jymmm> archivist: have you had to make replacement parts for it?
[19:56:55] <mk0> hly cow and this is not a joke. all our labs chiefs are from 40-s
[19:57:04] <archivist> Jymmm, yes
[19:57:24] <archivist> made a wooden bearing one day
[19:57:35] <mk0> they all hardly walk
[19:57:51] <alex4nder> hey
[19:58:04] <Jymmm> archivist: well, it is a moving part, so not really a fair comparison to a 100yo induction furnace
[19:58:36] <mk0> wooden bearing. you troll
[19:58:43] <Jymmm> lol
[19:58:44] <archivist> steaming tomorrow and monday
[19:58:54] <archivist> mk0, really not a joke
[19:59:39] <archivist> its the bearing for the outlet valve of the air pump
[20:00:16] <mk0> those, who operate equipment from 60-s do not ever joke
[20:00:37] <alex_joni> mk0: you were the one looking for foam?
[20:00:41] <mk0> i mean myself
[20:00:45] <alex_joni> it's in master
[20:00:53] <alex_joni> sim/axis/axis_foam.ini for an example
[20:00:57] <mk0> lookinf for foam in what sense?
[20:01:16] <mk0> nope, it was about xuyv-foam patch
[20:01:22] <alex_joni> yes
[20:01:31] <alex_joni> it's merged into master as of march
[20:01:31] <mrsun_> anyone got any good machining videos from youtube? .. maybe channels? :)
[20:01:37] <mrsun_> i need something to watch =)
[20:01:56] <mrsun_> hand machinists are the most fun to watch :P
[20:02:00] <syyl_ws> you know mr. mueller nicks videos?
[20:02:01] <mk0> hmm, i didn't see. i looked through several times but didn't see (
[20:02:06] <syyl_ws> about scraping, casting and a bit cnc
[20:02:09] <archivist> mrsun_, upset yourself with the fast tool changer on the brother cnc
[20:02:19] <mrsun_> archivist, already done ... :P
[20:02:31] <mrsun_> syyl_, seen :/
[20:02:41] <syyl_ws> :D
[20:03:07] <mrsun_> and KEFs ... and all of hoss, and all mrpete
[20:03:16] <syyl_ws> mh
[20:03:22] <syyl_ws> you could go to the shop
[20:03:30] <syyl_ws> machine something, make a video and watch that :D
[20:03:34] <mrsun_> syyl_ws, showered, naked and in bed :P
[20:03:47] <mrsun_> sleepy time here :/
[20:03:48] <syyl_ws> to much detail ;)
[20:04:03] <mrsun_> syyl_ws, pfft ... to much detail would be ... ;P
[20:04:20] <mk0> alex_joni, axis/axis_foam.ini for an example ! i read your post not carefully. Thanks!
[20:04:28] <mrsun_> syyl_ws, thats almost like a dare to say ... you know :P
[20:04:38] <syyl_ws> *runs away*
[20:04:44] <alex_joni> mk0: sim/axis/axis_foam.ini for an example ;)
[20:04:52] <alex_joni> that's the config you might want to try
[20:05:17] <mk0> yep i will definitely
[20:05:31] <mk0> xchat shows smileys??? oh, no...
[20:05:40] <syyl_ws> only yours Oo
[20:05:41] <archivist> mrsun_, search double ended lathe
[20:07:13] -!- FinboySlick has quit [Quit: Leaving.]
[20:14:31] -!- syyl_ws has quit [Quit: Verlassend]
[20:19:09] -!- dimas_ [[email protected]] has joined #linuxcnc
[20:21:53] <SolarNRG> Well thanks for your help and advice, I think it is not a good idea to have an induction melter as I won't be able to power it effectively
[20:22:17] <mk0> yes
[20:23:22] <mk0> and maybe solar cells too...[joking
[20:23:31] <alex_joni> In practice, foundries use between 500 and 800 KWh /mt to raise steel to a little above its melting point of 1535deg C.
[20:24:19] <Jymmm> alex_joni: Shit, my lil hand held honda generate can do 800KW, no problem!
[20:24:32] <Jymmm> and only on one gallon of gas!
[20:24:50] <SolarNRG> That's probably more power than comes into my entire home
[20:25:27] <Tom_itx> 800Kw?
[20:26:06] <mk0> do not joke with big energies, without knowing you may find yourself dead. that's really not a joke.
[20:26:21] <Jymmm> Tom_itx: do you know of any speech modules that wotk with an ardunio?
[20:26:36] <Tom_itx> txt to speech or speech
[20:26:44] <Tom_itx> i have a couple speech boards
[20:27:08] <Jymmm> Tom_itx: Something simple to replace idiot lights for the blind
[20:27:12] <Tom_itx> one is just a recorder
[20:27:37] <Tom_itx> use a buzzer and beep out morse code
[20:27:43] <Jymmm> a counter is what I'm after
[20:28:04] <Jymmm> Tom_itx: Fine, you learn braille, and I'll use CW
[20:28:41] <mrsun_> Jymmm, impossible to generate 800KW on 1 gallon of gas
[20:29:09] <Jymmm> mrsun_: Sure it is, and in a HAND HELD generator too!
[20:29:09] <mrsun_> 34 - 40KW or something
[20:29:22] <mrsun_> and thats raw heat energy
[20:29:31] <mrsun_> without counting the mechanical losses in your engine :P
[20:30:04] <Jymmm> mrsun_: Dude, it was a joke, and I said in a HAND HELD (less than 40lbs) generator
[20:30:21] <Jymmm> mrsun_: Dont be goin all MrScience on us now =)
[20:30:26] <mrsun_> Jymmm, haha =)
[20:30:44] <mk0> :DD
[20:31:00] <mrsun_> cant remember the exact kw content of gas :/
[20:31:06] <SolarNRG> 1 gallon, hmm maybe 800kw for 30 seconds!?
[20:31:21] <Jymmm> 30mS maybe
[20:31:23] <mrsun_> SolarNRG, you got about 9kw or so per liter of gasoline
[20:31:27] <mrsun_> in energy
[20:31:28] <SolarNRG> IF you had an engine efficient enough
[20:31:29] <alex_joni> Jymmm: yeah, but you don't have one mt of metal
[20:31:38] <Jymmm> mt ?
[20:31:38] <alex_joni> I assume mt is metric ton
[20:31:45] <alex_joni> which is about 2000lbs
[20:31:56] <SolarNRG> So you'll get that amount of power for less than 100miliseconds then
[20:31:58] <Jymmm> alex_joni: what do I need with all that?
[20:31:59] <SolarNRG> per litre
[20:32:01] <SolarNRG> or about half a second
[20:32:04] <SolarNRG> for a gallon
[20:32:19] <SolarNRG> This kid made a 150w induction loop
[20:32:25] <alex_joni> but 800kWh for 2000lbs means you might need only lots less for 1-2lbs
[20:32:26] <SolarNRG> Why Can't I make a 2KW loop
[20:32:31] <SolarNRG> I think that is reasonable
[20:32:35] <alex_joni> I'm sure it's not linear though
[20:32:37] <SolarNRG> But I don't understand how to make it
[20:33:09] <SolarNRG> Maybe a 2kw loop wouldn't be super duper fast at melting metals but would it not suffice?
[20:33:16] <Jymmm> SolarNRG: Dude, just do propane and a leaf blower like everyone else.
[20:33:27] <mk0> ))))
[20:33:27] <mrsun_> SolarNRG, but still ... you have still only burned 1 gallon of gas ... and that still has no more then the 34 - 40kw energy content :P
[20:33:28] <SolarNRG> I'm against using combustible gases
[20:33:48] <SolarNRG> kw is powe
[20:33:49] <Jymmm> SolarNRG: What do you think will be produced from the molten metal?
[20:33:52] <SolarNRG> kw/h is energy
[20:34:06] <mrsun_> ahh true .. im just trying to sound smart :P
[20:34:24] <SolarNRG> a toxic zinc oxide vapour
[20:34:47] <SolarNRG> I went down the all electric road with microwaves
[20:34:50] <SolarNRG> It didn't work
[20:34:54] <SolarNRG> But i'm sure induction loop will
[20:34:57] <mrsun_> god damn uranium-235 is energy dence =)
[20:35:14] <Jymmm> mrsun_: lick it!
[20:35:27] <mrsun_> 79 500 000 MJ / Kg =)
[20:35:40] <mrsun_> compared to 47.2 MJ / Kg for gas :P
[20:35:51] <Jymmm> mrsun_: Hawt Damn, think amazon carries it?
[20:35:59] <mrsun_> i would rather have antimetter
[20:36:11] <mrsun_> theoretical is 180 000 000 000 MJ / Kg
[20:36:15] <Jymmm> I'd rather have anti-matter
[20:36:41] <mrsun_> anti-mater :P
[20:36:42] <mrsun_> matter
[20:36:47] <mrsun_> antimatter!
[20:36:49] <mrsun_> wth =)
[20:36:51] <Loetmichel> hmm, but a bit difficult to contain ;-)
[20:36:54] <mrsun_> metter? .. wth is that
[20:37:01] <Jymmm> dont matter either way =)
[20:37:14] <Jymmm> mrsun_: you lick the 235, didn't you?
[20:37:20] <Jymmm> licked
[20:37:23] <mrsun_> Jymmm, im not telling
[20:37:32] <Jymmm> I think you just did =)
[20:37:36] <Loetmichel> see if he glows in the dark... ;-)
[20:37:52] <Jymmm> Cool, dead glowing skin cells!
[20:38:01] <mrsun_> im so readioactive that people see me in x-ray
[20:38:11] <Jymmm> <rimshot>
[20:38:26] <mrsun_> wth is that ? :P
[20:38:35] <mrsun_> turned a babe upside down and took a shot from the rim ? ;P
[20:38:38] <mrsun_> (thinking rimjob)
[20:38:50] <Jymmm> mrsun_: http://instantrimshot.com/index.php?sound=rimshot&play=true
[20:38:58] <mk0> haha, SolarNRG is a troll from ##physics
[20:39:08] <mrsun_> Jymmm, oh :P
[20:39:09] <Loetmichel> hmm, i hop i havent bit off more than i can chew. anyone has milled slate from a Billard table?
[20:39:13] <mrsun_> thats far from what i was thinking
[20:39:13] <Jymmm> mk0: and #chemistry
[20:39:24] <mk0> :D no. he is really there
[20:39:28] <Loetmichel> i have to make the trophy stands out of an old Billard plate
[20:39:31] <Jymmm> mrsun_: perv
[20:39:38] <mrsun_> Jymmm, guilty as charged :/
[20:39:40] <Jymmm> mk0: I know, and in ##chemistry too
[20:39:50] <Jymmm> mrsun_: Keep up the good work =)
[20:40:18] <Jymmm> Ok, I'm off (in more ways than one) for a bit!
[20:40:33] <mrsun_> fingers fell off?
[20:40:42] <Loetmichel> mrsun_: rimschot= "tusch" in german
[20:40:45] <Loetmichel> -h
[20:40:59] <mrsun_> Loetmichel, and as im swedish you think that would help me how? :P
[20:41:14] <Loetmichel> oh, sorry, i somehow have sorted you to germany ;-)
[20:41:21] <mrsun_> haha =)
[20:41:48] <mrsun_> Loetmichel, cause of the rimshot thing? ... its stuff that i think germans could do im their dirty dirty movies
[20:42:06] <Loetmichel> and sorry again, my swedish is about 25 jears not used
[20:42:29] <mrsun_> va bar d� kan jag s�ga lite vad jag vill h�r nu d� ? :P
[20:42:34] <Loetmichel> and even then it was just the amount a gir can teach you on 2 weekends ;-)
[20:42:34] <mrsun_> bar->bra
[20:42:43] <Loetmichel> girl
[20:42:54] <SolarNRG> How am I a troll?
[20:43:02] <mrsun_> Maza-Trol! :P
[20:43:26] <SolarNRG> I actually build stuff, I actually test stuff, I video what I do and I share my videos with people, how is this trolling?
[20:43:49] <alex4nder> wut
[20:43:50] <mrsun_> SolarNRG, making magnet engines etc? :)
[20:43:58] <mrsun_> magnet generators
[20:44:20] <SolarNRG> I wasn't very successful at that either mrsun, my magnets were misaligned and acted more as dampeners rather than bearings
[20:44:39] <Loetmichel> hmmm...
[20:44:47] <SolarNRG> The positioning of your holes must be very precise
[20:45:00] <Loetmichel> i dont get how ANYONE with an egineering backgound can belive in overunity machines.
[20:45:12] <Loetmichel> +b
[20:45:13] <SolarNRG> I will admit I failed to build one
[20:45:16] <Loetmichel> grrr
[20:45:19] <Loetmichel> -b+n
[20:45:21] <SolarNRG> I will also admit I have failed to melt metal in a microwave
[20:45:25] <mk0> SolarNRG, you're furthermore a grammar troll! i explode
[20:45:37] <alex4nder> SolarNRG: you actually tried the microwave? what happened?
[20:45:40] * mrsun_ can see bits of mk0 flying by
[20:46:02] <mrsun_> mk0, tried the meling glass trick ? :)
[20:46:02] <SolarNRG> Alex yes
[20:46:12] <mrsun_> SolarNRG*
[20:46:22] <SolarNRG> http://www.youtube.com/watch?v=xlxbVKkm71E
[20:46:50] -!- cmorley has quit [Ping timeout: 260 seconds]
[20:47:06] <SolarNRG> Just because I have failed to replicate someone's claim doesn't mean I'm right that it cannot be done
[20:47:10] <mrsun_> omg so brittish!
[20:47:13] <mrsun_> it hurts =)
[20:47:27] <alex4nder> SolarNRG: you ever heard the term 'keep it simple'?
[20:47:33] <alex4nder> it's a good default
[20:47:42] <SolarNRG> I like rube-goldberg methods
[20:47:47] <mk0> my butt melts
[20:48:10] <alex4nder> if it's complex, it's probably not going to work
[20:48:25] <Loetmichel> SolarNRG: if it comes to overunity machines: it CANT be done. Physics lawas are loaws, not suggestions
[20:48:28] <Loetmichel> laws
[20:48:38] <SolarNRG> TBH most of my channel are failed experiments, although I can be proud that I have been honest with my results
[20:48:38] <alex4nder> well
[20:48:49] <alex4nder> Loetmichel: they're 'rules' with REALLY high probability. ;)
[20:49:27] <SolarNRG> A lump of enriched plutonium seems to defy thermodynamics, at first glance it is a rock that is hot and continues to get hotter and hotter and will stay this way for years and years and years... Then we re-wrote science to account for "nuclear fission"
[20:49:52] <SolarNRG> One energy I firmly belive in is solar steam turbine
[20:50:03] <Loetmichel> alex4nder: as far as we know they are "written in stone". Someone who will build a overunity machine has to invent a WHOLE new physics first
[20:51:00] <Loetmichel> SolarNRG: IF you can build a magnetic monopole you CAN build your overunity machine...
[20:51:13] <Loetmichel> but taht is also not supposed to happen ;-)
[20:51:32] <mrsun_> but if you take a N/S magnet and cut it in half
[20:51:34] <alex4nder> watching too much Fringe, I think
[20:51:41] <mrsun_> shouldnt you have one north pole magnet and one south pole magnet then ?
[20:51:45] <SolarNRG> I can turn 48 neodymium magnets into a sort of monopolar arrangement by bolting them all down with 3mm bolts
[20:51:51] <Loetmichel> mrsun_: ... you get 2 NS magnets with half the size
[20:52:02] <mrsun_> aww .... im not stupid ;P
[20:52:13] <mrsun_> ok maybe i am .. but not that stupid
[20:52:20] <alex4nder> ...
[20:52:20] <mrsun_> ofc you get one N magnet and one S magnet!
[20:52:22] <mrsun_> silly
[20:52:29] <SolarNRG> http://www.youtube.com/watch?v=J68eplT9v2Y
[20:52:34] <SolarNRG> This was as close as I got
[20:52:38] <Loetmichel> *sigh*
[20:52:56] <mk0> mrsun_, as one greek said - the more i know the more i'm stupid
[20:53:35] <mrsun_> Loetmichel, sorry
[20:53:36] <mrsun_> =)
[20:53:51] <Loetmichel> mk0: that greek was right
[20:53:53] <mrsun_> damn im on a strange mood tonight ...
[20:54:11] <Loetmichel> SolarNRG: i dont see your problem
[20:54:19] <Loetmichel> magnetic bearings are simple
[20:54:21] <mrsun_> im more like, the more i know the more i just want to kill myself cause there is no meaning to be on this earth :P
[20:54:22] <mk0> yep. right/ i mean mrsun_ must not blame himself )
[20:54:53] <Loetmichel> but i would use some ring mangnets polarized axially
[20:55:04] <mk0> aand from futurama: there's no scientific consesus that life is important
[20:55:20] <Loetmichel> 2 small ones on the axle and 2 double size on the holder
[20:55:20] <mk0> *consensus
[20:55:46] <Loetmichel> mk0: it isnt. but mearly indestructibe as whole
[20:55:51] <Loetmichel> nearly
[20:56:14] <mk0> the first sentence is by Socrates
[20:57:38] <SolarNRG> My problem is I am a brain damaged retard with autism who lives on DLA and his idea of engineering involves a saw, hand drill and a file over a bit of the kitchen peninsula
[20:58:00] -!- n2diy [[email protected]] has joined #linuxcnc
[20:58:34] <alex4nder> wut
[20:58:43] <alex4nder> did someone just steal your keyboard, or did you change personalities?
[20:59:15] <mk0> SolarNRG, all scientist are of that kind
[20:59:18] <Loetmichel> whats DLA?
[20:59:27] <SolarNRG> Disability Living Allowance
[20:59:32] <Loetmichel> ah
[20:59:50] <SolarNRG> I have brain damage and I have autism and trichotillomania
[20:59:55] <SolarNRG> And PTSD and anxiety
[20:59:55] <alex4nder> SolarNRG: join the channel, and build a mill.
[21:00:05] <alex4nder> it'll give you something to build, that works
[21:00:11] <alex4nder> and then you can get all OCD on your spindle runout
[21:00:14] <Loetmichel> but since when is autims considered retarded and a brain damage?
[21:00:22] <alex4nder> and freak out about .001 of backlash
[21:00:25] <Loetmichel> or did you meand brain damage AND autism?
[21:00:25] <SolarNRG> The autism I got in 86
[21:00:31] <SolarNRG> The brain damage I got in 2006
[21:00:39] <SolarNRG> yes both separate conditions
[21:00:52] <SolarNRG> I'm getting a back payment soon
[21:00:57] <SolarNRG> Should I do an X2 conversion?
[21:01:12] <SolarNRG> I'd really like a desktop gear maker
[21:01:27] <SolarNRG> I have the arduino and the stepper motors
[21:01:39] <SolarNRG> I don't have a parellel port, I felt the Gecko wouldn't be suitable for me
[21:01:50] <SolarNRG> I have nema 34s
[21:02:03] <mk0> don't have a parellel port? how can it be?
[21:02:16] <SolarNRG> I'm on a laptop with a dead battery plugged into the mains and it is now my main PC
[21:02:23] <SolarNRG> My Quad core is dead
[21:03:51] <alex4nder> time for a raspberry pi
[21:04:06] <SolarNRG> Arduino bangs on about them like they're the bee all to end all
[21:04:22] <SolarNRG> We got an ipad 1
[21:04:35] <SolarNRG> You can't do nothing on that thing, no torrents, no flash, no PDF nothing
[21:04:41] <DJ9DJ> gn8
[21:04:52] <mk0> Stephen Hawking
[21:05:06] <mk0> everyone must do things he can do
[21:05:13] <alex4nder> hah
[21:05:17] -!- DJ9DJ has quit [Quit: bye]
[21:08:18] <ReadError> how does one acquire autism ?
[21:09:03] <SolarNRG> Chickenpox in infanthood
[21:09:26] <SolarNRG> disrupts mirror neurol development
[21:09:45] * ReadError isnt sure if trolling or not..
[21:09:51] <Loetmichel> i ever thought autism is a birth/genetic defect?
[21:10:01] <ReadError> me too
[21:10:40] <mk0> ReadError, i think it's too hard to troll with it
[21:11:27] <mk0> only people with no morality can troll this topic
[21:12:02] <SolarNRG> My brother does not have it but I do
[21:12:06] <Loetmichel> and found more than average on ppl with trisomie 21, so the scientist link that gene to the autism?
[21:12:09] <SolarNRG> I was able to talk when I was 2
[21:12:13] <SolarNRG> But I could not when I was 3
[21:12:28] <SolarNRG> Nobody else in my family has it
[21:13:01] <alex4nder> ReadError: yoh
[21:13:06] <ReadError> hello sir
[21:13:08] <alex4nder> how's it?
[21:13:11] <ReadError> man
[21:13:16] <ReadError> strugglin getting this toolpath made
[21:13:21] <ReadError> i realize i could do it in gcode
[21:13:33] <ReadError> but i want a viable means to do it consistently for more complex stuff
[21:13:48] <SolarNRG> If I want a CNC machine that can make gears, what should I buy?
[21:13:54] <ReadError> celebrating national homebrew day cookin up a batch :)
[21:14:25] <alex4nder> ReadError: what material? and you talking about that image you pasted the other day?
[21:14:26] <Loetmichel> has anyone milled slate?
[21:14:30] <ReadError> yea alex4nder
[21:14:43] <Loetmichel> or was that question just not read?
[21:14:50] <ReadError> i realize it wouldnt be too bad to generate the code by hand
[21:14:57] <Loetmichel> SolarNRG: anyone
[21:15:00] <ReadError> but thats just the 1st piece, the others will be much more complex
[21:15:09] <Loetmichel> and a program to generate the richt toolpath ;-)
[21:15:17] <Loetmichel> right
[21:15:18] <SolarNRG> Isn't it going to cost like 4 thousand pounds for a good CNC mill?
[21:15:23] <ReadError> i think pfred or archivist cuts gears also?
[21:15:30] <Loetmichel> SolarNRG: depends.
[21:15:42] <Loetmichel> mine has cost me about 500$ in parts
[21:15:53] <Loetmichel> and mills planetary gears just fine ;-)
[21:16:00] <SolarNRG> :o
[21:16:09] <mk0> mine too
[21:16:15] <Loetmichel> http://www.cyrom.org/palbum/main.php?g2_itemId=11702
[21:16:17] <SolarNRG> I love planetary gearboxes, you can have 2 motors or more driving a single rotor
[21:16:19] <Loetmichel> http://www.cyrom.org/palbum/main.php?g2_itemId=11711
[21:16:26] <Loetmichel> http://www.cyrom.org/palbum/main.php?g2_itemId=11714
[21:16:32] <Loetmichel> http://www.cyrom.org/palbum/main.php?g2_itemId=11714
[21:16:46] <SolarNRG> That's beautiful
[21:17:09] <SolarNRG> I don't think I'm clever enough to build one, I'd rathe buy one
[21:17:26] <mk0> buy???
[21:17:36] <SolarNRG> yeah, save up for a year
[21:17:40] <Loetmichel> i had to make the planets 3 times 'cause i didnt took the shrinking of the hollow gear into accound when pressed into the box
[21:17:41] <mk0> that;s not even 4000 pounds
[21:17:48] <mk0> it's 20
[21:17:49] <alex4nder> ReadError: the only thing that's hard is making a nice cut.. if you're doing 1/4" aluminum or something, you can't just make those arcs in one pass.
[21:18:03] <alex4nder> ReadError: so you have to employ some type of material remove strategy
[21:18:14] <ReadError> alex4nder, maybe 1/8th inch aluminum
[21:18:22] <ReadError> but i got some plastics i can use also
[21:18:23] -!- iwoj has quit [Quit: Computer has gone to sleep.]
[21:18:37] <alex4nder> ReadError: so I've been using a edge-milling strategy.. and keeping the chip load at like .002"
[21:18:42] <ReadError> i can cut the same path 3x ?
[21:18:45] <ReadError> at different depths
[21:18:50] -!- iwoj [[email protected]] has joined #linuxcnc
[21:18:53] <alex4nder> that's one strat, and it works
[21:18:54] <Loetmichel> ReadError: or 100 times...
[21:18:56] <Loetmichel> ;-)
[21:19:06] <alex4nder> but I like taking off 'tall' small pieces.
[21:19:11] -!- tlab [[email protected]] has joined #linuxcnc
[21:19:24] <alex4nder> so I run the cutter at the maximum depth, and shave off small pieces at a time
[21:19:28] <alex4nder> and I move at like 30 IPM
[21:19:35] <ReadError> pycam does the outside in the big hole fine
[21:19:44] <ReadError> but it doesnt want to 'drill' the other ones for some reason
[21:19:49] -!- mk0 has quit [Quit: Leaving]
[21:19:50] <alex4nder> just leave them out
[21:19:58] <alex4nder> and add them to the file manually
[21:20:01] <alex4nder> as a peck drill routine
[21:20:01] <ReadError> yea i could do another path for that
[21:20:01] <Loetmichel> http://www.cyrom.org/palbum/main.php?g2_itemId=12760
[21:20:07] <Loetmichel> http://www.cyrom.org/palbum/main.php?g2_itemId=12766
[21:20:11] <Loetmichel> http://www.cyrom.org/palbum/main.php?g2_itemId=12773
[21:20:42] <Loetmichel> that was 300 times around ;-)
[21:20:46] <alex4nder> yah
[21:20:48] <alex4nder> that's one approach
[21:20:53] <alex4nder> I've been doing this..
[21:21:38] <alex4nder> Loetmichel: http://www.youtube.com/watch?v=ELfONtG_Zkk#t=1m
[21:21:50] <alex4nder> that's at .20 DoC
[21:22:19] <alex4nder> the chips were really consistent, and the machine really liked the constant load
[21:22:34] <Loetmichel> alex4nder: http://www.cyrom.org/pce/connectbar.avi
[21:23:09] -!- tlab has quit [Client Quit]
[21:23:20] <Loetmichel> http://www.cyrom.org/pce/lochknabbern.avi
[21:24:33] <alex4nder> cool
[21:25:04] <alex4nder> now we just need an opensource replacement to VoluMill, HyperMill, or SurfCAM. :P
[21:26:15] <alex4nder> ok
[21:26:25] <alex4nder> I'm going to go try to get 100 IPM out of my taig
[21:26:41] <ReadError> hmm
[21:26:45] <ReadError> i havnt tried any of those yet
[21:26:52] <ReadError> they have fully functional trials?
[21:27:10] <Loetmichel> alex4nder: hmmm, thats 2540mm/min, right?
[21:27:13] <Loetmichel> sounds easy
[21:27:35] <alex4nder> Loetmichel: easier said than done
[21:27:43] <alex4nder> most people run their taigs at < 60
[21:27:51] <alex4nder> w/ steppers
[21:28:01] <Loetmichel> the mini mill i have build does 3m/min if driven with 40V
[21:28:29] <Loetmichel> atm i have only 32V supply, so the maximum speed is about 2,5m/min
[21:28:49] <Loetmichel> and my steppers have only 1A/phase
[21:29:18] <Loetmichel> but: my mill has ball bnearings on round steel as ways
[21:29:26] <Loetmichel> not V-shape glide things
[21:29:55] <alex4nder> these screws are 20 TPI
[21:30:40] <ReadError> should i order some drill bits instead of cutting the holes with an endmill ?
[21:30:44] <r00t4rd3d> how can i cut tslot straight with a hacksaw?
[21:30:57] <alex4nder> r00t4rd3d: lube the saw with butter
[21:31:05] <ReadError> sounds like you need a router?
[21:31:10] <syyl_> tslot? hacksaw?
[21:31:16] <r00t4rd3d> lol
[21:31:18] <alex4nder> ReadError: endmill on that is fine
[21:31:20] <syyl_> there must be something in the air today
[21:31:47] <alex4nder> yah
[21:31:58] <alex4nder> it's cinco de mayo, everyone is drunk
[21:32:23] <r00t4rd3d> i dont drink
[21:32:33] <syyl_> you can cut a tslot with a hacksaw, if you exchange it with a milling machine and a tslot cutter...
[21:33:14] <r00t4rd3d> its only 1x1inch
[21:33:18] <alex4nder> or you could move to a buddhist monastery and bring the metal and a bastard file with you
[21:33:25] <alex4nder> and spend some time.. alone.
[21:33:51] <r00t4rd3d> i can probably do it in a vise
[21:34:05] <r00t4rd3d> and use the vise as my guide
[21:34:09] <alex4nder> alright.
[21:34:16] <syyl_> sell the hacksaw, take the money and go to a machineshop
[21:34:18] <syyl_> Oo
[21:34:23] <alex4nder> what is this for?
[21:34:30] <r00t4rd3d> just a spacer
[21:34:55] <alex4nder> why does it need to be a t-slot then?
[21:35:13] -!- iwoj has quit [Remote host closed the connection]
[21:35:14] <r00t4rd3d> cause i have an extra piece collecting dust
[21:36:06] <ReadError> alex4nder, how often do you lube the leadscrews?
[21:36:15] <alex4nder> whenever they're dry
[21:36:19] <r00t4rd3d> lol
[21:36:25] <ReadError> pretty hard to get to em
[21:36:36] <alex4nder> you mean X?
[21:36:38] <ReadError> i need a longer needle i think
[21:36:39] <ReadError> yea
[21:36:42] <alex4nder> yah, it blows
[21:38:23] <alex4nder> ok, bbl
[21:40:21] <r00t4rd3d> ReadError, goto the hardware store and buy a grease nipple and make a block
[21:41:10] <ReadError> still impossibru to get to
[21:41:14] -!- fliebel has quit [Remote host closed the connection]
[21:41:22] <r00t4rd3d> mine are easy
[21:43:01] -!- petteriu [[email protected]] has joined #linuxcnc
[21:43:06] <gene__> Hi guys, problem with g76 after I made close loop spindle speed work. It goes to a point at about the first cut depth, and sits forever waiting for a spindle index, which is there
[21:43:53] <gene__> Any idea what I might have messed up in the hal file that is stopping that?
[21:51:50] <alex4nder> r00t4rd3d: how would he make a block to grease the leadscrews on the underside of his table?
[21:55:00] -!- bedah has quit [Quit: gn8]
[22:00:03] <ReadError> so, i was talking with my dad
[22:00:11] <ReadError> he said they have whole bins of scrap metal at work
[22:00:15] <ReadError> some large pieces
[22:00:25] <ReadError> from f35 parts
[22:00:31] <ReadError> hes gonna grab me some ;)
[22:00:38] <alex4nder> nice
[22:00:39] <ReadError> surely they got some decent aluminum and such
[22:01:08] <ReadError> on problem is i wouldnt know what kind of aluminum it is
[22:01:29] <alex4nder> who cares
[22:01:34] <alex4nder> unless you're welding
[22:01:38] <alex4nder> or making critical parts
[22:01:41] <ReadError> ya
[22:01:42] <jdhNC> free is free.
[22:01:53] <alex4nder> my aluminum is the shitty household kind you get at Ace
[22:01:55] <ReadError> most aluminum i can cut at about the same rate?
[22:01:58] <alex4nder> it's like milling gummy bears
[22:02:20] <ReadError> i got a 36" of 1" bar
[22:02:26] <ReadError> i can cut a bunch of goodies with that
[22:02:29] <alex4nder> ReadError: I think you can pretty much crank your spindle speed up as high as you want.. the one worry you'll have is chips welding to your endmill
[22:02:29] <ReadError> 6061 i think
[22:02:32] <alex4nder> and smearing.
[22:02:42] <alex4nder> so a little lube goes a long way
[22:02:57] <ReadError> coolant would be nice
[22:03:00] <ReadError> but ide make a mess of it
[22:04:42] -!- petteriu has quit [Remote host closed the connection]
[22:07:46] <alex4nder> ReadError: I'll put up pics of my new rig and filter.
[22:09:10] <ReadError> ooo nice
[22:25:45] -!- stan [[email protected]] has joined #linuxcnc
[23:01:57] <toastydeath> gummy aluminum is the biggest problem at low feed rates
[23:02:49] <toastydeath> finishing gummy aluminum takes a very sharp tool with a generous nose radius
[23:13:10] -!- i_tarzan [[email protected]] has joined #linuxcnc
[23:15:18] -!- i_tarzan_ has quit [Ping timeout: 272 seconds]
[23:32:24] -!- skunkKandT has quit [Remote host closed the connection]
[23:45:59] -!- i_tarzan_ [[email protected]] has joined #linuxcnc
[23:47:54] -!- i_tarzan has quit [Ping timeout: 252 seconds]