#linuxcnc | Logs for 2012-06-06

Back
[00:03:31] -!- Jim_ [[email protected]] has joined #linuxcnc
[00:06:47] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has parted #linuxcnc
[00:18:32] -!- dimas has quit [Ping timeout: 252 seconds]
[00:31:27] -!- toastydeath has quit [Read error: Connection timed out]
[00:32:31] -!- dimas [[email protected]] has joined #linuxcnc
[00:42:00] -!- Thetawaves [[email protected]] has joined #linuxcnc
[00:43:32] <Tom_itx> anybody around? i have a q about tool lengths
[00:44:13] <Tom_itx> the way my mill software used to be was that i would set the z fixture offset with the tip of the first tool then preceeding tools were an offset of that
[00:44:51] <Tom_itx> ie tool one would have a zero offset
[00:45:33] <Tom_itx> do i still enter the offset for tool one as an offset from absolute z zero?
[00:45:54] <Tom_itx> and subsequent tools
[00:46:08] <Tom_itx> i think i can figure it out better by just doing it
[00:47:00] -!- Valen [[email protected]] has joined #linuxcnc
[00:50:36] <andypugh> Tom_itx: No, your reference / touch-off tool would normally have zero length in the table. However, having the actual physical length would also work.
[00:51:37] <andypugh> The important thing is that you should only ever touch-off the coordinate system with tool 1, so that you don't change its offsets. And you must always be careful to touch-off the other tools into the tool table.
[00:51:49] <Tom_itx> i'm just acustomed to doing it a certain way
[00:52:22] <Tom_itx> so are the other tools an offset from the first?
[00:52:30] <andypugh> However, if the other tools are correctly touched-off, then you can touch off the coordinate system with them too. (but if they are not correctly touched-off, then you break everything)
[00:52:32] <Tom_itx> if the first has zero offset
[00:52:57] <andypugh> If the first has zero offset then yes, the others are deltas.
[00:53:02] <Tom_itx> ok
[00:53:35] <Tom_itx> it's been so long since i ran the big ones i actually forgot what we did on those but i think we used a dowel pin as the first tool
[00:53:58] <Tom_itx> and most of them had routines built in to set tools
[00:54:33] <andypugh> That's a possibility too, if you have a tool-length probe.
[00:54:42] <andypugh> Time for me to sleep.
[00:54:47] <Tom_itx> ok thanks
[00:54:48] -!- andypugh has quit [Quit: andypugh]
[00:56:30] -!- ve7it has quit [Remote host closed the connection]
[00:56:38] -!- jd896 [[email protected]] has joined #linuxcnc
[00:57:20] -!- syyl_ has quit [Quit: Leaving]
[01:00:45] -!- jd896 has quit [Ping timeout: 244 seconds]
[01:18:19] <elmo40> anyone in SC?
[01:19:15] <Jymmm> Santa Cruz, Santa Clara, Santa Claritia, Southern California,
[01:19:26] <elmo40> south carolina ;)
[01:19:28] <Jymmm> Stir Crazy
[01:19:32] <elmo40> stone cold
[01:19:49] <elmo40> myrtle beach, ever been?
[01:19:57] -!- Jim_ has quit [Remote host closed the connection]
[01:22:03] <Tom_itx> where's that dad gum bearing link again. i lost it in my bookmarks
[01:24:22] <Jymmm> Tom_itx: https://bookmarks.google.com/
[01:24:38] <Jymmm> err
[01:25:02] <Tom_itx> i dunno what machine it's on though
[01:25:15] <Jymmm> Tom_itx: https://www.google.com/bookmarks/?hl=en
[01:25:49] <Jymmm> Tom_itx: Just drag the bookmarklet to your browsers toolbar to add a link quickly
[01:26:53] <Tom_itx> vxb
[01:27:04] <Jymmm> .com in Ornage County California
[01:27:15] <Jymmm> http://support.google.com/bookmarks/bin/answer.py?hl=en&answer=174971
[01:29:28] <Jymmm> Used to be King Bearing... http://web.applied.com/
[01:35:47] <Connor> What do you call the covers that are in front of the tables in allot of CNC mill's? It's not a way cover.. They tend to be made of stainless and typically look to be deep enough for the vise to be fully supported?
[01:36:24] <Connor> http://i132.photobucket.com/albums/q18/jid2/IMG_2214.jpg
[01:36:41] <Connor> that mill has one in front, and on the side..
[01:37:24] <Tom_itx> acordion covers
[01:37:47] <Tom_itx> oh, i dunno about those
[01:41:24] <Valen> never seen one of those before
[01:41:48] -!- norias [[email protected]] has joined #linuxcnc
[01:41:50] <norias> hi
[01:44:14] <pcw_home> transit FTW
[01:44:51] <Valen> 100% cloud cover here
[01:45:25] <pcw_home> I'm amazed at how much you can see with lousy binocs propped up on the deck railing projecting onto a piece of paper
[01:45:41] <Valen> do be careful doing that
[01:45:49] <pcw_home> Venus + about 7 sun spots
[01:45:57] <Valen> if the light winds up hitting the side of the tube it can cause problems
[01:46:08] <pcw_home> about 1.5" diameter sun
[01:46:26] <Valen> one of my friends was using a 10" telescope for some solar observing, was chatting to his neighbour about it
[01:46:34] <Valen> then smoke starts pouring out of the scope
[01:46:34] <pcw_home> yeah got to keep it aligned
[01:46:52] <Valen> the sun image hit the side of the tube, luckily it was fireproof cardboard
[01:46:55] <pcw_home> there goes the secondary mount...
[01:47:14] <Valen> thankfully no lol
[01:47:44] <Valen> the worst he did was "its a bit bright, i know i'll put my moon filter (eyepiece) in
[01:47:56] <Valen> it lasted about a second and a half before it exploded
[01:48:14] <Valen> (he was projecting of course)
[01:48:50] <Valen> if you put some cardboard around the binocs so your otherwise in good shadow it'll improve your contrast
[01:48:58] <pcw_home> no you want a full size filter
[01:49:01] <Valen> better still do it inside into a dark room
[01:49:23] <Valen> yeah he "well duh that was dumb" afterwards lol
[01:49:41] <pcw_home> Yeah im still amazed at how good it looks (especially if dead-on axis)
[01:49:59] <Valen> we were in the third year of our space science degree at the time lol he really should have known better
[01:50:17] <pcw_home> (glad you reminded me though, I brought the binocs in)
[01:50:35] <Valen> even a straight magnifying glass can do a decent job
[01:51:38] -!- skunkworks__ has quit [Ping timeout: 240 seconds]
[01:51:40] <pcw_home> I'd set my telescope up but 8" is a bit scary amount of sunlight
[01:51:55] <elmo40> ya, just a little, eh?
[01:52:03] <elmo40> http://www.ustream.tv/channel-popup/star-gazers-eclipse
[01:52:06] <elmo40> watch it online :)
[01:52:31] <Valen> you can normally project it onto a big screen with it
[01:52:46] <Valen> the cheat way of lining it up is to put some foil over the front of it
[01:52:54] <Valen> and punch like a 1" hole in it
[01:53:34] <pcw_home> Yeah but this is just a Dobsonian and easy to bump
[01:53:35] <Valen> http://www.nasa.gov/multimedia/nasatv/index.html
[01:54:23] <pcw_home> Yeah they had a little flare earlier
[01:54:38] <Valen> its not "that" bad
[01:54:59] <pcw_home> no I mean a solar flare
[01:55:11] <pcw_home> little bitty one on the bottom
[01:55:18] <Valen> i meant the sun isnt that bad
[01:55:40] <Valen> you normally have a few minutes of observing time
[01:56:01] <Valen> we did it with the .5 meter dob at the university
[01:56:09] <Valen> projected it onto a wall inside the building lol
[01:56:19] <Tom_itx> i suppose that's another one we aren't able to see here
[01:56:21] <Valen> (with the scope outside)
[01:56:22] <pcw_home> I alway sort of had this idea that if you didn't have a Ha filter you really could n ot see anything
[01:56:35] <Tom_itx> is it visible now?
[01:56:37] <Valen> Tom_itx: where are you?
[01:56:41] <Tom_itx> Ks usa
[01:56:41] <Valen> can you see the sun?
[01:56:51] <pcw_home> from here yes
[01:56:51] <Tom_itx> too late now i'm afraid
[01:57:04] <Valen> then you missed it
[01:57:07] <Jymmm> OMG! WHAT HAPPENED TO THE SUN! IT"S GONE!
[01:57:08] <pcw_home> anyone that can see the sun can see it
[01:57:13] <Valen> started about 4 hours ago
[01:57:29] <Valen> there is a region that doesnt get to see them
[01:57:42] <Jymmm> antartica?
[01:57:46] <pcw_home> Oh ok but is pretty small
[01:58:15] <Jymmm> pcw_home: werent we able to se it at 3pm?
[01:58:19] <Valen> http://en.wikipedia.org/wiki/Transit_of_Venus,_2012
[01:58:26] <Valen> fig 1
[01:58:40] <pcw_home> Had to go home no binocs at work
[01:58:52] -!- Tom_L [Tom_L!~Tl@unaffiliated/toml/x-013812] has joined #linuxcnc
[01:59:05] <Tom_L> 15 min ago i could have seen it
[01:59:59] -!- zlog_ [[email protected]] has joined #linuxcnc
[02:00:07] -!- Tom_itx has quit [Disconnected by services]
[02:00:10] Tom_L is now known as Tom_itx
[02:00:57] -!- zlog has quit [Ping timeout: 252 seconds]
[02:01:08] <pcw_home> Pretty neat we had a great eclipse for this area and now this
[02:01:18] -!- zlog_ has quit [Remote host closed the connection]
[02:01:31] <Jymmm> pcw_home: Just wait till the moon disappears!
[02:01:34] -!- zlog [[email protected]] has joined #linuxcnc
[02:02:07] <Tom_itx> i saw the eclipse just before the sun went behind the trees
[02:02:19] <Valen> pcw there was a lunar eclipse recently? or is it coming
[02:02:25] <Tom_itx> this is alot more rare isn't it?
[02:02:45] <Valen> yeah
[02:02:48] <pcw_home> Yes quite rare
[02:02:58] <Valen> theres 2 about 5 years apart then about 100 years for the next one
[02:03:20] <pcw_home> not sure about the lunar but there was about a 80% solar a couple weeks ago
[02:03:21] <Valen> hell i'm here because of the one 2 cycles ago
[02:03:28] <Valen> lunar is pretty common
[02:03:46] <Tom_itx> solar is less common
[02:03:58] -!- joe9 has quit [Quit: leaving]
[02:04:18] <Valen> (captain cook, went to tahiti to observe the last one, came home the long way around and "discovered" australia on the way)
[02:18:11] -!- Thetawaves has quit [Quit: This computer has gone to sleep]
[02:26:25] <Valen> pcw_home: we also used the solar filter on the scope to do direct observation, IE hold the filter up and look through it ;->
[02:26:31] <Valen> the sun is suprisingly small
[02:27:33] -!- demacus_ [[email protected]] has joined #linuxcnc
[02:28:11] <pcw_home> I guess only a full aperture filter is safe
[02:29:37] <Valen> oversafe for direct observation i spose
[02:30:38] <Valen> some reflective mylar would probably do if you wanted to do projected observation
[02:30:43] <Valen> i wouldn't put my eye to it
[02:30:59] -!- demacus has quit [Ping timeout: 245 seconds]
[02:31:05] <Tom_itx> i used welding goggles the other day
[02:32:06] <pcw_home> No I'm happy just to see it projected
[02:32:08] <pcw_home> (they say the .003% transparency welding goggles are OK for observing the sun)
[02:32:31] <Valen> shade 12 i think thats called
[02:32:44] <Valen> though i think they want 14 or something now
[02:33:20] <pcw_home> Well that what someone on the NASA transit show said anyway
[02:33:58] <Tom_itx> i forget the number on mine but they're pretty dark
[02:34:05] <Tom_itx> i've got spare shaded glass
[02:34:14] <Tom_itx> i can double them up and you can't hardly see a thing
[02:34:33] <Valen> i see a few spots of blue sky on the horison
[02:35:44] <Valen> "If your telescope has a finder, you should also put a filter on it or use a dust cover and secure it with tape. Unprotected viewing through the finder will lead to the same kind of optical damage as viewing through the telescope. In addition, an uncovered finder directed at the sun can lead to exceedingly unpleasant scalp burns while you're viewing."
[02:35:54] <Valen> it sounds like that is a lesson learnt the hard way
[02:37:38] <pcw_home> Ouch!
[02:40:58] -!- sumpfralle has quit [Read error: Operation timed out]
[03:03:12] -!- norias has quit [Ping timeout: 244 seconds]
[03:04:53] -!- MarkusBec_ [[email protected]] has joined #linuxcnc
[03:05:26] -!- theorb [[email protected]] has joined #linuxcnc
[03:05:46] -!- MarkusBec has quit [Quit: UAVP-NG]
[03:05:47] -!- ReadError has quit [Read error: Connection reset by peer]
[03:05:47] -!- ReadError [[email protected]] has joined #linuxcnc
[03:05:47] -!- e-ndy has quit [Quit: ZNC - http://znc.sourceforge.net]
[03:05:47] MarkusBec_ is now known as MarkusBec
[03:06:42] -!- e-ndy [[email protected]] has joined #linuxcnc
[03:07:49] -!- Keknom has quit [Quit: Leaving.]
[03:09:55] -!- theorbtwo has quit [Ping timeout: 260 seconds]
[03:09:56] theorb is now known as theorbtwo
[03:27:16] <jdhNC> no problems pulling the bolts out?
[03:29:57] -!- iwoj has quit [Quit: Computer has gone to sleep.]
[03:35:43] <Tom_itx> is there a feedrate override in automatic mode?
[03:45:42] -!- iwoj [[email protected]] has joined #linuxcnc
[03:47:17] -!- n2diy has quit [Quit: Ex-Chat]
[03:57:30] -!- ktchk [[email protected]] has joined #linuxcnc
[03:57:44] <Jymmm> the slider?
[03:58:21] -!- ktchk [[email protected]] has parted #linuxcnc
[04:04:43] <Jymmm> archivist: #40 http://homepage3.nifty.com/amigos/index-e.html
[04:17:31] <Valen> http://homepage3.nifty.com/amigos/vise/vise-e.htm is nice
[04:17:59] <Valen> i think half of this guys appeal is the good camera work and a clean shop lol
[04:18:24] <Jymmm> A clean shop/desk is a sign of a sick mind!
[04:18:44] <Valen> hmm, i have both a dirty desk, and a dirty mind
[04:18:54] <Jymmm> ditto
[04:19:43] <Jymmm> QUICK what is the weirdest thing on your desk???
[04:31:46] <djdelorie> you?
[04:32:08] -!- i_tarzan has quit [Ping timeout: 240 seconds]
[04:32:08] <djdelorie> ok, not very quick ;-)
[04:32:28] <Jymmm> djdelorie: I'm not on your desk sily!
[04:32:37] <Valen> a solar garden light?
[04:32:38] <djdelorie> desk, desktop, what's the difference? ;-)
[04:33:13] <Jymmm> I'm not a cheaper hooker, I'm easy, just not cheap!
[04:33:52] <djdelorie> there are so many weird things on my desk, it's hard to choose. I'd have to go with the spinning wheel spindle.
[04:34:33] <Valen> carpet tape?
[04:34:57] <Valen> ooh the smashed up remains of the LCD and touch screen of a mobile phone in a drinking glass
[04:34:58] -!- vladimirek [[email protected]] has joined #linuxcnc
[04:35:32] <Jymmm> http://www.docstoc.com/docs/5718003/The-Miracle-Blaze-Fact-Sheet-HOW-IS-MIRACLE-BLAZE
[04:36:07] <Jymmm> it was a buck at dollar store, so I said what the hell
[04:38:21] <Jymmm> oh and two bolts epoxied together, but I don't thnk that even comes close to weird in this channel.
[04:39:53] <Jymmm> Valen: IN a drink glass? Is the glass half full or half empty? And is there any fluid in it?
[04:40:01] <Valen> there was
[04:40:16] <Valen> but i drank it before filling it with glass shards
[04:40:21] <Jymmm> solvents dont count
[04:45:38] <Jymmm> a compound miter saw works great on cutting aluminum extrusion, but I really need to get a good one one of these days.
[04:52:43] -!- kb8wmc has quit [Quit: ChatZilla 0.9.88.2 [Firefox 12.0/20120423130206]]
[05:03:31] -!- Fox_Muldr has quit [Ping timeout: 265 seconds]
[05:04:30] -!- _abc_ [_abc_!~user@unaffiliated/ccbbaa] has joined #linuxcnc
[05:05:05] -!- Fox_Muldr [[email protected]] has joined #linuxcnc
[05:06:08] -!- iwoj has quit [Ping timeout: 240 seconds]
[05:15:35] <Jymmm> I love these things, it's for everything you wouldn't use a pair of scissors on http://www.toolup.com/wiss_v10_10-14-duckbill-combination-pattern-snips.aspx
[05:16:09] <Jymmm> they look weird, but cut like crazy
[05:16:18] -!- Thetawaves [[email protected]] has joined #linuxcnc
[05:17:17] <Jymmm> the ones I have are much older though, might be different now.
[05:19:00] <Jymmm> mine say 'drop forged' on the handles
[05:55:31] <alex4nder> so what's up with the bug I logged not getting any feedback?
[05:55:36] <alex4nder> even when I submitted a patch
[05:56:20] <alex4nder> this is some non-sense.
[05:57:15] <Jymmm> life beyond emc? Venus?
[05:58:45] <alex4nder> I don't believe.
[06:06:18] <Thetawaves> anybody here built a circuit with rs485?
[06:17:06] -!- mk0 [[email protected]] has joined #linuxcnc
[06:20:30] -!- psha[work] [psha[work][email protected]] has joined #linuxcnc
[06:24:13] -!- Thetawaves has quit [Quit: This computer has gone to sleep]
[06:28:17] -!- Poincare [Poincare!~jefffnode@2001:470:cb24:4::2] has joined #linuxcnc
[06:33:09] -!- micges [[email protected]] has joined #linuxcnc
[07:00:36] -!- DJ9DJ [DJ9DJ!~Deejay@unaffiliated/dj9dj] has joined #linuxcnc
[07:00:43] <DJ9DJ> moin
[07:10:12] -!- mhaberler [[email protected]] has joined #linuxcnc
[07:10:20] <DJ9DJ> moin
[07:11:34] -!- gambakufu has quit []
[07:13:15] -!- gambakufu [[email protected]] has joined #linuxcnc
[07:16:04] <mrsun> didnt take much force at all to move the lathe bed ... i thought it would be tougher then that ... but didnt even feel it in the wrench =)
[07:28:15] -!- mov [[email protected]] has joined #linuxcnc
[07:32:55] -!- mov has quit [Client Quit]
[07:33:02] -!- rakija [[email protected]] has joined #linuxcnc
[07:33:54] -!- vladimirek has quit [Remote host closed the connection]
[07:40:31] -!- rakija has quit [Quit: Leaving]
[07:40:58] -!- rakija [[email protected]] has joined #linuxcnc
[07:54:58] <Loetmichel> mornin#
[07:55:01] <Loetmichel> '
[07:58:18] <Jymmm> g
[08:02:26] <Jymmm> Somebody fax me some teflon wire
[08:03:22] <Loetmichel> hrhr, how a bit sorting and some boxes/shelves can change a room... -> http://www.cyrom.org/palbum/main.php?g2_itemId=13290 ... yesterday mornin that was a pile of messy cardboxes with NO system in it ;-)
[08:03:41] <Valen> looks spensive
[08:03:50] <Jymmm> I go ya beat =)
[08:04:03] <Valen> jamie of mythbusters has everybody beat
[08:04:17] <Jymmm> no, I got him beat too
[08:04:37] <Loetmichel> Valen: such a plastc box costs 2.99 Eur
[08:05:48] <Loetmichel> not expensive, just the 2 ppl 1 day soring is expensive. i hope the co-workers are now respecting that and will sort the incoming package material in the according boxes
[08:06:02] <Loetmichel> and not just drop it somewhere
[08:06:19] <Loetmichel> s/soring/sorting
[08:06:37] <Jymmm> Loetmichel: http://i53.tinypic.com/212wxtt.jpg
[08:06:59] <Jymmm> It's on a rolling rack =)
[08:08:06] <Loetmichel> hrhr
[08:08:37] <Loetmichel> the "delivery corner" is in the company i work for, not at hom
[08:08:40] <Loetmichel> e
[08:08:44] <Jymmm> I have 4 more of those chrome racks too.
[08:08:56] <Loetmichel> THERE is a lot of sorting still to do...
[08:08:59] <Loetmichel> <- messie
[08:09:23] <Jymmm> I could never find shit, that's why I did that. Each box is labeld with it's contents.
[08:09:55] <Jymmm> the other 4 racks have the jamie sized containers on them
[08:13:25] <Loetmichel> i am cleaning up at home... the last 3 weeks. 'til now i have discarded about 2 cubic meteres of trash... and sorted most of my tools... the room doesent look any less messy :-(
[08:13:48] <Loetmichel> ... and why the hell hso i have about 10 PCB side cutters?
[08:13:52] <Loetmichel> ;-)
[08:14:03] <Loetmichel> s/hso/do
[08:14:44] <Jymmm> you need yourself soem of these =) http://i29.tinypic.com/17daon.jpg
[08:15:18] <Jymmm> aka, toolbox #2 =)
[08:16:02] <Loetmichel> i am a cheapskate, i solve that different: http://www.cyrom.org/palbum/main.php?g2_itemId=12727
[08:16:36] <Jymmm> and THATS why it still looks messy =)
[08:16:57] <Loetmichel> company had some spare PC PSU boxes... so i made a shelf for them
[08:17:00] <Jymmm> Besides, that was FREE! Gotta love craigslist =)
[08:17:22] <Loetmichel> hrhr
[08:17:33] <Jymmm> I did give them some nice cookies though
[08:17:41] <Jymmm> as a thank you
[08:18:03] <Jymmm> ppl give away good stuff
[08:18:07] <Loetmichel> i simply havent got enouth storage to sort away all my stuff.
[08:18:18] <Loetmichel> shoud do more discarding .
[08:18:47] <Jymmm> the trick is to have a place to put it all
[08:19:07] <Jymmm> like that 6 draw cabinet, the chrome racks, etc
[08:19:53] <Jymmm> when I move, I'm just gonna shrink wrap the whoel rack and roll it on the moving truck.
[08:20:32] <Jymmm> no packing, no boxing, no stacking.
[08:30:44] -!- jstenback has quit [Ping timeout: 260 seconds]
[08:31:23] -!- rakija has quit [Quit: Leaving]
[08:31:51] -!- jstenback [jstenback!~jstenback@2620:101:8003:200:224:e8ff:fe39:34c2] has joined #linuxcnc
[08:36:39] -!- vladimirek [[email protected]] has joined #linuxcnc
[08:38:09] * Tom_itx wonders if Jymmm eve sleeps
[08:38:26] <Tom_itx> ever*
[08:42:00] -!- rakija [[email protected]] has joined #linuxcnc
[08:44:15] <Jymmm> Tom_itx: When I'm dead
[08:44:34] <Tom_itx> that's my philosophy
[08:45:29] <Jymmm> In the meantime, I'll just keep working on this heating element =)
[08:46:19] -!- pingufan [[email protected]] has joined #linuxcnc
[08:47:21] <Jymmm> finally found some springs that'll work, but had to cut them in half
[08:48:23] <Jymmm> when I get done, should be good for around 1000F of spot heat
[08:48:40] <Valen> i dont know why, but i read that as a heating *helmet*
[08:49:02] <Jymmm> Well, it sorta kind looks like a helmet =)
[08:49:07] <Tom_itx> blame it on venus
[08:49:33] <Jymmm> the shield that is
[08:49:34] -!- rakija has quit [Quit: Leaving]
[08:50:24] -!- rakija [[email protected]] has joined #linuxcnc
[08:53:21] -!- rakija has quit [Client Quit]
[08:53:45] -!- rakija [[email protected]] has joined #linuxcnc
[08:56:47] -!- rakija has quit [Client Quit]
[09:16:13] -!- mhaberler has quit [Quit: mhaberler]
[09:47:13] -!- phantoxe [[email protected]] has joined #linuxcnc
[10:04:24] -!- jd896 [[email protected]] has joined #linuxcnc
[10:04:40] <jd896> Is pcw in?
[10:05:19] <Valen> he's probably asleep
[10:05:48] <jd896> Course what time z is he in
[10:06:24] <Valen> america somewhere i think
[10:10:21] <jd896> Yeah it's 6.10 in florida
[10:10:24] <jthornton-2> it's 3am at pcw's house
[10:10:48] <jd896> Where is he from then or have I guessed wrong
[10:11:30] <jthornton-2> left coast
[10:11:45] jthornton-2 is now known as jthornton
[10:12:12] <jd896> J Thornton is that big John t ?
[10:12:18] <jthornton> aye
[10:13:00] <jd896> How do from the uk mate
[10:13:46] <jthornton> just opening my eyes for a new day
[10:13:52] <jthornton> 5am here
[10:15:53] <jd896> Morning in that case
[10:24:59] <jd896> John what are we looking for when adding I in the pid pcw told me to do p ff1 I d I have done the p and ff1 it following down during cruse
[10:25:46] <jd896> I mean the following is good during cruse but how will I effect the scope reading
[10:26:59] <jthornton> I'm not that sharp on it and had to do my CHNC by trial and error... add a little watch the trace
[10:27:07] <jthornton> how close are you now?
[10:28:35] <jd896> 0.08 is perhaps the largest spike
[10:28:41] <jthornton> I mainly focused on the accel and decel part and the cruse seemed to take care of it self for me
[10:28:50] <jthornton> mm?
[10:28:58] <jd896> Yes
[10:29:24] <jthornton> iirc a plasma?
[10:29:32] <jthornton> that's pretty close
[10:29:33] <jd896> Yeah
[10:30:10] -!- syyl [[email protected]] has joined #linuxcnc
[10:31:04] <jthornton> I've been trying to follow along on the forum as I have a tuning job coming up when I pull the plug on my Anilam control on the old BP knee mill here soon
[10:40:38] -!- vladimirek has quit [Remote host closed the connection]
[10:41:44] -!- ktchk [[email protected]] has joined #linuxcnc
[10:43:00] <jthornton> wow only one spammer tried to register last night
[10:46:30] <jd896> Register to the forum
[10:46:45] <jthornton> yea
[10:47:02] <jthornton> at one point there was 50-60 a day
[10:47:28] <jthornton> 98% using gmail accounts
[10:47:47] <jd896> Wow there spam bots I imagin not individuals
[10:47:52] -!- pingufan has quit [Quit: Konversation terminated!]
[10:48:25] <jthornton> it's hard to say how they get past the captia thingy
[10:49:04] <jd896> Yeah thatsc
[10:49:36] <jd896> That's what there there for to stop the bots
[10:50:07] <jd896> Ai must be on the up
[10:51:19] <jthornton> most of them come from Russia, China, and India
[10:52:20] <jthornton> I get the IP of everyone that registers and compare that to what country they put on the form if the name sounds anything legit
[10:53:48] <jd896> At 50 to 60 a day that's a whole morning job there mate
[10:55:55] <archivist> isnt .08 close enough for plasma?
[10:56:27] <archivist> considering iirc you mentioned some backlash
[10:57:02] <jthornton> yea, that was a pain but most of them used names that gave them away easy to delete and ban the IP
[10:57:31] <jd896> Ah the backlash is on the other axis that's still away off yet I'm not sure of the accuracy that these are ment to hold
[10:58:17] <archivist> I dont know the accuracy of plasma cuts anyway
[10:58:36] <Valen> they have a taper too
[10:58:57] <Valen> it depends on alot of stuff how accurate you can make a plasma cut
[10:59:27] <jd896> If the torch is at the right hight and speed then the edge can rival a flame cut
[10:59:46] <jthornton> the main thing I pushed for on my plasma was acceleration so I could keep the speed up when rounding a corner
[11:02:04] <Valen> thats what seem to be underestimated most with CnC
[11:02:20] <Valen> everybody espouses their rapids, bit not the acceleration as much
[11:03:20] <archivist> they dont all have all the clue :)
[11:03:40] <jthornton> some used to claim the rapid speed of both X and Y combined
[11:05:17] <archivist> often one sees a user chasing the wrong metric
[11:06:54] -!- micges_ [[email protected]] has joined #linuxcnc
[11:07:16] <jthornton> I have a couple of subroutines for the plasma one trims off the sheet along the X axis and one for a square
[11:10:03] -!- micges has quit [Ping timeout: 245 seconds]
[11:10:28] <jthornton> I like this counter bore subroutine I created yesterday
[11:11:25] <jthornton> I need to pull the plug on the Anilam and get the BP knee mill converted to LinuxCNC
[11:12:17] <archivist> big step :)
[11:13:03] <archivist> I hate the knowledge one cannot use a tool for a period
[11:13:11] <jthornton> I've got all the wires traced out and I run the spindle now with LinuxCNC so it's just a matter of adding the axes
[11:13:25] <jthornton> yea, that is the sticky part
[11:14:52] -!- jd896 has quit [Ping timeout: 252 seconds]
[11:17:23] -!- jd896 [[email protected]] has joined #linuxcnc
[11:17:38] <jd896> jd896 I'm supprised you used the functioning control at all I'd have thought it'd have only been bought to be retro
[11:18:00] <jthornton> The Anilam?
[11:18:14] <jd896> Yeah
[11:18:29] <Valen> i hate needing to use the tool to make the tool
[11:18:31] <jthornton> I've had it for quite some time and it was my first CNC machine
[11:19:14] <jthornton> I used it to make my plasma after I discovered that I could actually load EMC onto a computer with the LiveCD
[11:19:27] <archivist> Valen, that requires mid work reassembly !
[11:19:43] <jthornton> every attempt at using the BDI failed
[11:19:46] <jd896> Ah so it was before emc even got a look in
[11:19:52] <jthornton> yea
[11:20:15] <jd896> Bdi ?
[11:20:45] <jthornton> that was the Brain Dead Installer for EMC before the LiveCD
[11:21:18] <jthornton> I guess my brain was dead back then dunno or my hardware was not right or something
[11:21:54] <jd896> Oh take it that's why emc's now on Ubuntu for the live cd or has it always been ubuntu
[11:22:13] <archivist> installing stuff in the brain just takes longer with age :)
[11:22:44] <jthornton> iirc the BDI was not ubuntu
[11:23:26] <jd896> Must admit Ubuntu makes Linux usable for most people
[11:24:19] <jd896> Most people don't know windows even has a command line never mind using command in Linux
[11:24:33] <jthornton> yes it does, I can't wait for cad and cam to catch up to ubuntu
[11:25:33] <jd896> Yeah that's pretty much all it needs to maybe catch solid works and autocads attention
[11:25:39] <jthornton> I started out with a 286 on DOS 4 or 5 I can't remember now
[11:26:01] <jthornton> yea that would be real nice to have a ubuntu solidworks
[11:26:53] <archivist> or an open source solidworksalike
[11:27:03] <jd896> That was most Likly before I got started John I'm only 21
[11:27:30] <jthornton> yea, that was a long time ago for sure
[11:28:06] <jd896> First one I had was a cast off 98me 2 machine
[11:28:16] <jthornton> a blank green screen with C:> burned into the left upper corner
[11:29:16] <jd896> Sounds like the old control for this esab I'm on
[11:29:23] <jthornton> mine was the deluxe model with a 10 mb hard drive and a 5 1/4 floppy and 512 mb of memory
[11:29:45] <archivist> bah you lot making me feel old...Science of Cambridge MK14 then a Commodore PET
[11:30:09] <jthornton> the Anilam motherboard is a 286 or 386
[11:30:22] <jd896> Ha I do remember those floppys that actually where floppy
[11:32:35] <jd896> S o c mk14 is that the Sinclair that was a kit ?
[11:33:50] <archivist> http://en.wikipedia.org/wiki/MK14
[11:34:13] <archivist> iirc we had a KIM1 at work at the time
[11:35:28] <archivist> hmm 1977, that does date me somewhat :)
[11:41:11] -!- norias [[email protected]] has joined #linuxcnc
[11:45:11] -!- jd896 has quit [Remote host closed the connection]
[11:47:06] -!- syyl_ [[email protected]] has joined #linuxcnc
[11:47:18] -!- jd896 [[email protected]] has joined #linuxcnc
[11:47:35] <jd896> As I said before my time
[11:49:39] <jthornton> this was my first http://en.wikipedia.org/wiki/IBM_XT
[11:49:56] <norias> yum
[11:49:58] <jthornton> I bought it where I worked at making nails to keep track of inventory
[11:50:01] <norias> XT was a 286, right?
[11:50:14] <jthornton> iirc yea
[11:50:21] <norias> yeah
[11:50:25] <norias> i started with a clone
[11:50:29] -!- syyl has quit [Ping timeout: 265 seconds]
[11:50:37] <norias> had a 286
[11:50:47] <norias> i want to say 10 MB HD
[11:51:00] <jthornton> nope 8088
[11:51:09] <norias> oh, wow
[11:51:28] <norias> good stuff
[11:51:43] <norias> did you have the FPU?
[11:52:45] <jthornton> too long ago to remember
[11:52:57] <norias> right on
[11:53:27] <jd896> Wow 4.77mhz
[11:53:39] <norias> yeah, today i will be explaining what irc is to one of the engineers i work with
[11:53:45] <norias> i think he will enjoy it alot
[11:55:07] <jd896> Tis a hidden gem this
[11:55:54] <norias> truly
[12:03:07] <jd896> Is pcw around yet
[12:03:30] <JT-Shop> he is sometimes up this early
[12:03:58] -!- jd896_ [[email protected]] has joined #linuxcnc
[12:04:17] -!- adb [[email protected]] has joined #linuxcnc
[12:05:40] <Tom_itx> archivist i had a commodore if it makes you feel any younger
[12:06:16] <archivist> I think JT-Shop was a late starter :)
[12:06:58] <Tom_itx> i think my first 8088 is still in the closet
[12:07:21] <Tom_itx> gave the commodore to the mailman's kid
[12:08:02] -!- jd896 has quit [Ping timeout: 260 seconds]
[12:08:03] -!- phantone [[email protected]] has joined #linuxcnc
[12:08:06] <archivist> I still have my MK14 and PET
[12:10:31] <archivist> the was no way it could be sold http://www.collection.archivist.info/archive/DJCPD/PD/2007/2007_05_01_PET_Computer/P4300006.JPG
[12:11:14] -!- phantoxe has quit [Ping timeout: 260 seconds]
[12:11:21] <Tom_itx> nice heater on a chilly morning
[12:12:04] <Tom_itx> my first graphic card did that pretty good as well
[12:15:46] <jd896_> http://www.raspberrypi.org/
[12:15:55] <jd896_> How things have come on
[12:28:23] -!- cevad has quit [Ping timeout: 245 seconds]
[12:31:15] -!- jd896_ has quit [Ping timeout: 252 seconds]
[12:50:26] -!- ktchk [[email protected]] has parted #linuxcnc
[12:59:49] -!- jd896 [[email protected]] has joined #linuxcnc
[13:08:42] <pcw_home> here now jd896
[13:11:45] -!- mhaberler [[email protected]] has joined #linuxcnc
[13:16:07] <pcw_home> rats
[13:19:04] -!- norias has quit [Ping timeout: 244 seconds]
[13:25:34] <jd896> Hi pcw as a continuation from the other day what am I looking for when adding I as I've noticed that it just seams to push the following error off
[13:28:25] <pcw_home> "I" should help but usually only when you are quite close
[13:28:27] <pcw_home> (it typically makes things worse with overshoots if the basic tuning is not close enough )
[13:29:58] <pcw_home> Do you have velocity mode servos?
[13:30:51] <jd896> Yes
[13:32:20] * JT-Shop collects another bit of servo tuning wisdom
[13:32:34] <pcw_home> for velocity mode servos its good to get FF1 dialed in first (this needs Halscope)
[13:34:09] <jd896> I did as you said and set p then ff1 I'm following during a cruse around 0.08
[13:34:56] <pcw_home> not so sure about wisdom, just slow osmosis after having done this a few hundred times
[13:34:58] -!- i_tarzan [[email protected]] has joined #linuxcnc
[13:35:36] <JT-Shop> much more experiance than my one time :-)
[13:36:08] <pcw_home> .08 inches or mm
[13:36:24] <jd896> And plenty more than my 0.5 times
[13:36:28] <jd896> Mm pcw
[13:36:28] <JT-Shop> when your tuning P and FF1 for a velocity drive what do you watch the acceleration part or the cruse part or both?
[13:36:53] <jdhNC> I have a bunch of Delta Tau systems with 'auto-tuning'. Not so great tuning.
[13:37:00] <pcw_home> FF1 is tuned by nulling the error during cruise
[13:37:12] <pcw_home> (for a velocity mode drive)
[13:37:58] <pcw_home> helps to have P low so the effect of FF1 is magnified
[13:40:13] <jd896> Yes the ff1 makes sense shal I post my latest scope to the forum
[13:40:36] <pcw_home> I would probably need a halscope plot of ferror/pidoutput/commanded and real velocity
[13:40:37] <pcw_home> to help much more
[13:41:52] <JT-Shop> jd896: what are you triggering on?
[13:41:54] <jd896> I'm looking for around 0.1 following if poss I'm at 0.4 ATM
[13:42:02] <jd896> I will do
[13:42:21] <jd896> Triggering on commanded velocity
[13:42:36] <JT-Shop> ok, just wondering
[13:43:06] <pcw_home> bbl doggy-walky
[13:43:06] -!- kb8wmc [[email protected]] has joined #linuxcnc
[13:43:25] <JT-Shop> me too
[13:44:23] -!- Valen has quit [Quit: Leaving.]
[13:47:24] -!- phantoxe [[email protected]] has joined #linuxcnc
[13:50:59] -!- phantone has quit [Ping timeout: 260 seconds]
[13:54:45] <jd896> Posted to my thread
[13:57:26] -!- Thetawaves [[email protected]] has joined #linuxcnc
[14:01:46] <Jymmm> JT-Shop: Where you asking pcw_home to walk you too, or that you had to walk your dog too?
[14:20:34] -!- psha[work] has quit [Quit: Lost terminal]
[14:24:59] -!- norias [[email protected]] has joined #linuxcnc
[14:32:25] -!- cmorley has quit [Ping timeout: 265 seconds]
[14:37:53] -!- Thetawaves has quit [Quit: This computer has gone to sleep]
[14:44:33] -!- DJ9DJ has quit [Quit: und wech]
[14:46:23] -!- norias has quit [Ping timeout: 244 seconds]
[14:48:38] -!- jd896 has quit [Remote host closed the connection]
[14:54:29] -!- isssy [[email protected]] has joined #linuxcnc
[15:02:50] -!- norias [[email protected]] has joined #linuxcnc
[15:07:51] -!- jd896 [[email protected]] has joined #linuxcnc
[15:11:23] -!- psha [[email protected]] has joined #linuxcnc
[15:17:08] -!- adb has quit [Ping timeout: 240 seconds]
[15:17:59] micges_ is now known as micges
[15:18:13] <jd896> You back pcw ?
[15:20:30] -!- isssy has quit [Quit: Bye Bye]
[15:20:33] -!- adb [[email protected]] has joined #linuxcnc
[15:22:26] -!- adb has quit [Read error: Connection reset by peer]
[15:22:45] -!- kb8wmc has quit [Quit: ChatZilla 0.9.88.2 [Firefox 13.0/20120601201853]]
[15:23:36] -!- cevad [[email protected]] has joined #linuxcnc
[15:25:05] -!- adb [[email protected]] has joined #linuxcnc
[15:26:10] -!- norias has quit [Ping timeout: 244 seconds]
[15:26:53] -!- mk0 has quit [Read error: Connection reset by peer]
[15:43:08] -!- jd896 has quit [Remote host closed the connection]
[15:54:28] -!- dimas has quit [Ping timeout: 244 seconds]
[16:16:36] <pcw_home> Yeah
[16:20:19] -!- mhaberler has quit [Quit: mhaberler]
[16:23:54] -!- mrsun has quit [Ping timeout: 245 seconds]
[16:34:06] -!- jd896 [[email protected]] has joined #linuxcnc
[16:36:58] -!- jd896_fabshop [[email protected]] has joined #linuxcnc
[16:38:05] <jd896_fabshop> john and pcw around
[16:38:10] <jd896_fabshop> ?
[16:39:57] -!- mrsun [mrsun!~mrsun@c-a93de253.4551536--62697410.cust.bredbandsbolaget.se] has joined #linuxcnc
[16:43:02] <archivist> best to ask the real question then they answer when at the console
[16:46:06] -!- jd896 has quit [Remote host closed the connection]
[16:55:49] <mrsun> gah broke of the tool holder "stud" or whatever its called ... (the one that goes from the crossslide into the tool holder and have a nut on it .. like a T nut etc) .. aparently i cant even weld
[16:55:49] <mrsun> think im gonna give away all my stuff and just sit and stare into a wall soon
[17:02:19] <archivist> I think after a rest and a coffee you will repair it properly
[17:06:25] <archivist> machines of that age may have bolts/studs etc made of wrought iron, it breaks like cast iron if not annealed now and again, specially with a shock load
[17:07:02] <pcw_home> jd896_fabshop around
[17:08:00] <mrsun> archivist, it was my homemade thingie that broke
[17:09:19] <mrsun> aparently i did some porous welding and left only like 3mm square that held the stud in place, ground it all off, rewelded and what do you know .. its freakin off to to the side ... so it only grabs the T slot in the cross slide on one side and is like 1mm up in the air in the other side
[17:09:38] <mrsun> have to realy torque it down if it is to be sitting properly .. and i do not like doing that to T slots
[17:10:21] -!- IchGuckLive [[email protected]] has joined #linuxcnc
[17:10:26] <IchGuckLive> Hi all on the Globe
[17:12:37] -!- puff has quit [Remote host closed the connection]
[17:25:34] -!- jd896_fabshop has quit [Remote host closed the connection]
[17:28:54] <IchGuckLive> havy poasting tonight
[17:31:22] <mrsun> archivist, ough you remember i was talking about making gears ? .. aparently the gears on my lathe is 15 degree ....
[17:31:41] <archivist> er 14.5 I bet
[17:31:50] -!- syyl_ws [[email protected]] has joined #linuxcnc
[17:33:01] <mrsun> reading about one making or looking for gears for the blomqvist lathe .. and aparently he had drawings and they said 15 degree =)
[17:33:23] <Connor> What's a good combination for a servo motor/driver to use as a spindle drive ? (For lathe/4th axis).. I can build my own servo using standard DC motor with H-bridge.. Just not sure if that's suitable for this or not.
[17:33:41] <Connor> Most of the motors I use are 12/24 motors for Power chair's .
[17:34:24] <IchGuckLive> MY1020 for Scooter is mutch better and cheeper
[17:34:39] <IchGuckLive> up to 1500W for 80USD
[17:35:00] <Connor> DC ?
[17:35:24] <Connor> What's the voltage ?
[17:35:53] <IchGuckLive> yes DC you can get them in 12/24/48V
[17:36:08] <IchGuckLive> look on ebay to MY1020
[17:37:03] <Loetmichel> hmmm
[17:37:13] <Connor> 2500 RPM ? That fast enough for lathe work?
[17:37:19] <archivist> mrsun, a new standard! or more like yet another gear standard, there are many
[17:37:23] <Loetmichel> is that suitable for a wheelchair (two of them)`?
[17:38:12] <Connor> okay.. I've found 24/36/48v versions.
[17:38:27] <Connor> Now to find a H-Bridge that can handle the voltage / amparage.
[17:39:11] <IchGuckLive> why not a Gecko 320
[17:40:03] <Connor> Maybe. not looked at Gecko's yet.
[17:40:17] -!- iwoj [[email protected]] has joined #linuxcnc
[17:40:23] <Connor> Do these have rear shafts on them for encoders ?
[17:40:37] <IchGuckLive> no
[17:40:52] <IchGuckLive> let me look i got a 350 in the E-Bike
[17:41:09] <IchGuckLive> how they made the frame
[17:42:33] <Connor> I think you want the encoder on the shaft of the motor, not the spindle for this would you not ?
[17:43:16] -!- syyl_ws has quit [Quit: Verlassend]
[17:43:23] <IchGuckLive> it is closed frame as i epected cause thats outside
[17:44:04] <IchGuckLive> as the motor is a very god live one you coudt desamble it and make a shaft into it
[17:47:05] <IchGuckLive> Connor: still here ?
[17:47:09] <Connor> yea
[17:47:50] <IchGuckLive> get the my1020 into google there you can see the diagramm and the other modells
[17:53:08] <IchGuckLive> slightly unsave -> http://www.youtube.com/watch?v=U3UCgX_jMWA
[17:55:36] -!- sumpfralle [[email protected]] has joined #linuxcnc
[17:58:42] -!- phantoxe has quit []
[18:05:47] -!- delkin [[email protected]] has joined #linuxcnc
[18:06:06] <IchGuckLive> by have a nice day
[18:06:12] -!- IchGuckLive has quit [Quit: ChatZilla 0.9.87 [Firefox 12.0/20120423130206]]
[18:11:10] -!- jd896_laptop [[email protected]] has joined #linuxcnc
[18:14:31] -!- i_tarzan has quit [Read error: Connection reset by peer]
[18:17:45] -!- i_tarzan [[email protected]] has joined #linuxcnc
[18:20:22] <Connor> Looking to build one like this.. http://www.youtube.com/watch?v=295Phu8GnjE
[18:26:26] -!- jd896_laptop has quit [Ping timeout: 252 seconds]
[18:32:41] -!- iwoj has quit [Ping timeout: 244 seconds]
[18:34:48] -!- ve7it [[email protected]] has joined #linuxcnc
[18:35:47] -!- delkin has quit [Ping timeout: 244 seconds]
[18:37:49] -!- dimas [[email protected]] has joined #linuxcnc
[18:40:18] -!- capricorn_1 [[email protected]] has joined #linuxcnc
[18:44:38] <mrsun> hmm, chatter in the lathe ... reasons ? .. to high rpm ? to much tool sticking out ?
[18:45:36] <archivist> also above center, too much overhang from chuck
[18:46:04] <archivist> loose headstock bearings
[18:46:18] <mrsun> got a 60mm thick piece in the chuck, with outstick about 50mm .... should be good ? :)
[18:46:26] <mrsun> archivist, headstocks bearings is more on the tight side
[18:46:45] <mrsun> (gets a bit hot when running :P)
[18:47:08] <archivist> try lower cutting speed
[18:47:09] <mrsun> tool holder (old one on the lathe) isnt the best tho ... seem to be right on center as it doesnt leave a small peg on the piece
[18:47:22] <mrsun> archivist, then i need to engage the broken backgears ... :/
[18:47:34] <mrsun> or cutting speed as in feed or rpm ? :)
[18:47:42] <archivist> yes
[18:47:51] <mrsun> sounds good when im about 10mm from the center, then the shatter stops
[18:47:58] -!- iwoj [[email protected]] has joined #linuxcnc
[18:48:10] <archivist> also tool geometry effects it
[18:49:07] <archivist> as I cannot hear it, its hard to guess what the cause is
[18:50:11] <mrsun> its a very very high pitch sound =)
[18:50:19] <archivist> whistle, tool
[18:50:27] <mrsun> i wll try tomorrow with lower rpm
[18:50:36] <mrsun> tho the gears doesnt sound to good with broken off teeth :P
[18:50:47] <archivist> put a finger on the tool does it stop
[18:50:58] <mrsun> yeah stupid person that had the lathe before made a tool holder from a round pipe to hold the small tools in
[18:51:29] <mrsun> not very rigid
[18:51:33] <mrsun> so i would guess its the tool =)
[18:51:33] <archivist> sounds like tool resonance then
[18:51:49] <archivist> shorter is better
[18:52:11] <mrsun> had no shatter at all with the new tools (16mm solid steel) but its the nut for that tool holder im remaking :P
[18:52:16] <mrsun> so have to use the old thingie =)
[19:00:51] -!- jd896_laptop [[email protected]] has joined #linuxcnc
[19:04:35] -!- freespace has quit [Ping timeout: 260 seconds]
[19:05:19] -!- frallzor [[email protected]] has joined #linuxcnc
[19:05:40] -!- freespace [[email protected]] has joined #linuxcnc
[19:09:09] -!- cylly2 [[email protected]] has joined #linuxcnc
[19:09:11] -!- andypugh [andypugh!~andy2@cpc2-basl1-0-0-cust639.basl.cable.virginmedia.com] has joined #linuxcnc
[19:09:13] -!- iwoj has quit [Ping timeout: 245 seconds]
[19:10:04] -!- mrsun has quit [Ping timeout: 269 seconds]
[19:11:08] -!- Loetmichel has quit [Ping timeout: 240 seconds]
[19:17:17] <jdhNC> am I the only one stuck working all day?
[19:19:06] <archivist> all of the UK was back at work today
[19:19:15] -!- iwoj [[email protected]] has joined #linuxcnc
[19:22:32] -!- mrsun [mrsun!~mrsun@c-a93de253.4551536--62697410.cust.bredbandsbolaget.se] has joined #linuxcnc
[19:25:42] -!- rakija [[email protected]] has joined #linuxcnc
[19:25:46] <andypugh> I was back _in_ work.
[19:29:23] -!- mhaberler [[email protected]] has joined #linuxcnc
[19:29:38] -!- jd896_laptop has quit [Ping timeout: 240 seconds]
[19:29:54] -!- iwoj has quit [Ping timeout: 260 seconds]
[19:32:42] -!- jd896_laptop [[email protected]] has joined #linuxcnc
[19:34:30] <Jymmm> andypugh: As opposed to OUT of work?
[19:34:56] <Jymmm> laid off? Fired? end of contract? etc?
[19:35:12] <andypugh> As opposed to "at work" and it's connotations of actually doing work.
[19:35:22] <Jymmm> ah, heh
[19:36:09] -!- rakija has quit [Quit: Leaving]
[19:37:56] <frallzor> omg best tool for alu-sheets ever!
[19:38:13] <frallzor> amana tools 1 flute cutter is THE shit
[19:38:56] <Jymmm> Ah, it's CRAP, gotit! ;)
[19:39:07] -!- psha has quit [Quit: Lost terminal]
[19:39:08] <frallzor> THE shiznits then? =P
[19:39:19] <Jymmm> lol
[19:39:38] <Jymmm> It's Kosher
[19:40:21] <frallzor> for real now, it was awesome
[19:40:25] <frallzor> not that expensive either
[19:40:37] <frallzor> even for me that have to import it
[19:40:50] <Jymmm> thickness? pics? Video?
[19:41:17] <frallzor> 2mm alu
[19:41:24] <frallzor> sticky kind
[19:41:42] <frallzor> 66% of 1/8 inch =P
[19:41:52] <frallzor> I hate imperial =(
[19:42:02] <Jymmm> i know what 2mm is
[19:42:18] <frallzor> surprisingly many dont =(
[19:42:27] <Jymmm> and 25.4mm too
[19:42:33] <Jymmm> == 1 "
[19:42:44] <Jymmm> but thats it
[19:43:11] <Jymmm> 13km 7 kg etc no clue
[19:43:40] <Jymmm> but I try =)
[19:44:35] <Jymmm> sorta, still using ounces, but only becuse I know what an ounce looks like
[19:44:41] <frallzor> =P
[19:44:51] <jdhNC> about 1/3rd of a baggie?
[19:45:37] <Jymmm> lol, actually no. I should have said fluid ounces.
[19:46:14] -!- jd896_laptop has quit [Ping timeout: 260 seconds]
[19:46:27] <Jymmm> and sadly if I was getting baggy, I wouldn't know by looking if I was getting ripped of or not =)
[19:46:35] <Jymmm> off
[19:47:00] <Jymmm> isn't three fingers an ounce or so?
[19:48:44] <jdhNC> three fingers probably weigh more than an ounce. Guess it depends on who had the fingers.
[19:48:54] -!- jd896_laptop [[email protected]] has joined #linuxcnc
[19:49:49] <frallzor> sweet, allmost perfect fit!
[19:49:55] <frallzor> I hate the human factor when
[19:50:03] <frallzor> I have to measure things by hand =)
[19:56:16] -!- morfic- has quit [Remote host closed the connection]
[19:57:47] -!- frallzoran [[email protected]] has joined #linuxcnc
[19:58:17] -!- jd896_laptop_ [[email protected]] has joined #linuxcnc
[19:58:22] -!- micges_ [[email protected]] has joined #linuxcnc
[19:58:35] -!- gambakufu has quit [Read error: Connection reset by peer]
[19:58:35] -!- micges has quit [Read error: Connection reset by peer]
[19:58:38] -!- _1SheYode [[email protected]] has joined #linuxcnc
[19:59:06] -!- morfic [morfic!~morfic@unaffiliated/morfic] has joined #linuxcnc
[19:59:13] -!- frallzor has quit [Ping timeout: 245 seconds]
[19:59:37] -!- jd896_laptop has quit [Ping timeout: 245 seconds]
[19:59:42] jd896_laptop_ is now known as jd896_laptop
[20:00:43] frallzoran is now known as frallzor
[20:01:06] -!- bostjan_2 [[email protected]] has joined #linuxcnc
[20:02:43] -!- bostjan_2 has quit [Remote host closed the connection]
[20:05:57] <andypugh> archivist: Feeling affluent? http://www.ebay.co.uk/itm/ws/eBayISAPI.dll?ViewItem&item=251078849199#ht_500wt_1413
[20:06:09] -!- jd896_laptop has quit [Ping timeout: 256 seconds]
[20:06:23] -!- micges_ has quit [Quit: Leaving]
[20:06:39] <andypugh> Actually, they might suit syyl_ too.
[20:07:26] <archivist> I need a job to feel affluent
[20:08:04] <andypugh> Surely you would be happy enough to have lots of money and no job?
[20:08:38] <archivist> first gimme da money
[20:10:15] <syyl_> i already got horn boring tools :P
[20:11:11] <archivist> I dont see 50 inserts as claimed
[20:11:32] <syyl_> i think i dont need 50 ;)
[20:11:41] <syyl_> they can be resharpened pretty easy
[20:12:28] <andypugh> I see 40
[20:12:31] <archivist> I usually grind up a bit of hss when doing the small stuff
[20:12:48] <archivist> I got to 42
[20:12:53] <andypugh> They have the advantage of being significantly stiffer, being all-carbide.
[20:12:54] <syyl_> but the hss is not that shiny :D
[20:13:13] <andypugh> And with a squirty-hole down the middle
[20:13:27] <syyl_> i set up shopair down that hole
[20:13:30] <syyl_> helps often
[20:13:38] <syyl_> to clean the chips out
[20:14:16] <andypugh> Perhaps you should go halves?
[20:14:26] <syyl_> hmm
[20:14:29] <syyl_> i think you need them :D
[20:14:41] <andypugh> But even then you would be spending money on something you woudn't otherwise buy.
[20:14:53] <syyl_> i just bought a tig welder
[20:14:54] <andypugh> I bought 20 the other day.
[20:15:06] <syyl_> thats enough for this month :D
[20:16:41] <syyl_> http://gtwr.de/wig1.jpg
[20:16:42] <syyl_> :P
[20:17:22] <archivist> floor too clean error at line 1
[20:17:42] <syyl_> i wet wipe the shop floor!
[20:18:06] <andypugh> I bought my TIG from eBay.de It seems that Germans bid lower than brits. :-)
[20:18:20] <syyl_> also a chinese unit?
[20:18:30] <andypugh> Yes
[20:18:39] <andypugh> But labeled "Felzer"
[20:19:10] <syyl_> i cant tell the difference between a esab, ewm, lorch or the chinese one.. :D
[20:21:02] <syyl_> but it gets the work done Oo
[20:21:02] <syyl_> http://gtwr.de/wig2.jpg
[20:21:08] <Jymmm> what archivist said!!!
[20:21:28] <andypugh> I wanted this one, but could't justify it: http://www.rehm-online.de/index.php?id=37&L=1
[20:21:43] <syyl_> rehm is also a good choise :D
[20:21:53] <Jymmm> andypugh: It's "cute"
[20:22:04] <syyl_> the price isnt
[20:22:34] <Jymmm> that's the interior designers markup
[20:22:49] <syyl_> more the name
[20:22:58] <syyl_> a ewm triton is also about 2,5k euro
[20:23:11] <syyl_> and that doesnt have the slick design :d
[20:23:43] <andypugh> The Rehm is also little, so motorbike-transportable.
[20:23:51] <Jymmm> lol
[20:24:03] <Jymmm> andypugh: got a genny outpur on the bike?
[20:24:05] <syyl_> the argon tank could be a problem on the bike
[20:24:23] <andypugh> I have disposables for that.
[20:24:23] <syyl_> ;)
[20:24:26] <syyl_> ah, ok
[20:31:10] <mrsun> welding stuff sucks ... it gets krooked as soon as you turn on the mig welder
[20:31:11] <mrsun> :P
[20:33:51] <syyl_> no problem
[20:34:02] <syyl_> just have a big deadblow hammer by hand :D
[20:34:30] -!- iwoj [[email protected]] has joined #linuxcnc
[20:38:42] <archivist> mrsun, learn to tag weld to hold it straight when final welding
[20:39:34] <mrsun> tag weld ?
[20:40:32] <mrsun> syyl_, problem is to hold the stuff to give it a wack :P
[20:40:59] <mrsun> im hoping i can counteract the little twist by having the two pieces in different configurations when i weld the other stuff to it =)
[20:41:11] <mrsun> sure it will have stresses but what doesnt after welding :P
[20:42:08] <frallzor> punktsvetsa
[20:42:14] <frallzor> loppor
[20:42:51] <frallzor> or in english; tag weld; beads =)
[20:43:12] -!- iwoj has quit [Ping timeout: 252 seconds]
[20:43:18] <gene77> Silly Q guys: g21 doesn't convert the axis dro's to metric, is there a quick & dirty way to do that?
[20:43:20] <mrsun> well i did that :P and it looked straight ...
[20:43:21] <mrsun> =)
[20:43:40] <mrsun> but ended up with pretty much the exact same twist in both pieces :P
[20:43:49] <mrsun> curse of not having a full workshop with big welding table i guess :P
[20:44:35] <andypugh> gene77: Doesn't it?
[20:44:41] <mrsun> frallzor, men det �r v�ll "tack" ? :)
[20:44:45] <mrsun> tack welding
[20:44:48] <mrsun> tack it down
[20:44:50] <mrsun> etc :P
[20:45:21] <mrsun> tag stands for tungsten active gas :P
[20:45:59] <frallzor> yeah yeah =P
[20:46:14] <frallzor> anyone into riveting?
[20:46:27] <mrsun> riv eating
[20:46:30] <andypugh> Yes. When appropriate
[20:46:44] <frallzor> will a rivet of 6.2mm hold 4mm of sheets?
[20:46:49] <fragalot> mrsun: there's a massive welding table @ one of the workshops @ work... found out it's warped last week
[20:46:50] <syyl_> you mean the old "beat the crap out of it"-riveting?
[20:46:52] <andypugh> I work on a 1916 vehicle, so do a fair bit of it.
[20:46:52] <fragalot> >.<
[20:47:07] <frallzor> I have no idea on how much material needed to hold
[20:47:08] <archivist> frallzor, yes/no /maybe
[20:47:22] <mrsun> fragalot, hehe =)
[20:47:28] <frallzor> its pretty much just "hold" pieces together
[20:47:37] <fragalot> frallzor: if it's just to hold it together, yes
[20:47:58] <andypugh> frallzor: 6.2 is fairly large for that thickness. The material will break first.
[20:48:18] <frallzor> I went for the longest yet not biggest I could find
[20:48:20] <archivist> depends on the head size too
[20:48:34] <frallzor> seemed pretty decent
[20:49:02] <andypugh> Well, yes, I was meanign that it will pull through rather than break.
[20:51:59] <archivist> my favourite riveting is hidden rivets
[20:55:09] <andypugh> Please elaborate?
[20:57:31] <gene77> No, and a .7 pitch metric thread is being cut at about 7 tpi
[20:57:48] <archivist> andypugh, clock dial repair http://www.collection.archivist.info/searchv13.php?searchstr=clock+dial+norfolk
[21:00:29] <gene77> 1916 what Andy?
[21:00:59] -!- iwoj [[email protected]] has joined #linuxcnc
[21:01:30] <andypugh> 1916 Dennis Fire Engine
[21:02:18] <gene77> Anyway, how do I put this in metric mode, dro and all. Now that puppy has to be one of a kind since its now 95 years old!
[21:02:51] <andypugh> Actually, there are several about. I know of at least 6
[21:03:06] <gene77> I'll be dipped. :)
[21:03:20] <andypugh> http://union.ic.ac.uk/rcc/rcsmotor/
[21:04:40] <andypugh> Actually. 21 that we know of :http://union.ic.ac.uk/rcc/rcsmotor/archive/surviving-n-types
[21:05:02] -!- iwoj has quit [Ping timeout: 246 seconds]
[21:06:03] <andypugh> gene77: Menu. View - Display mm
[21:06:04] <gene77> Considering their age, they actually look fairly modern!
[21:06:40] -!- mhaberler has quit [Ping timeout: 252 seconds]
[21:07:06] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has joined #linuxcnc
[21:07:16] -!- RussianKid has quit [Quit: Leaving.]
[21:07:35] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has joined #linuxcnc
[21:07:44] <gene77> That works, didn't know it was there. Now how do I get it to calculate the threads by the reciprocal of .7?
[21:08:04] <gene77> .7mm that is
[21:08:23] <syyl_> 0,7mm of pitch is pretty uncommon
[21:08:28] <syyl_> Oo
[21:08:35] <syyl_> sure it isnt 0,75mm?
[21:08:58] <gene77> std 4mm metric machine screw...
[21:09:12] <syyl_> arr damn :D
[21:09:15] <syyl_> right
[21:09:17] <syyl_> thats 0,7
[21:09:33] * syyl_ runs away and screams
[21:09:39] <andypugh> I just use an I of .7.
[21:10:09] <gene77> no need, I've asked far dumber questions here
[21:10:58] <syyl_> ;)
[21:11:02] <andypugh> Sorry, I don't mean I.
[21:11:14] <gene77> My code takes an input when in inches mode, of tpi, finds the reciprocal which is the movement per turn
[21:11:27] <andypugh> P is distance per rev. SO you use p 0.7
[21:12:08] <andypugh> Ah, in that case you need to use a pitch of 36.2857142857143 tpi
[21:13:06] <andypugh> Or, depending on if the code converts to metric of uses G21, you might want a pitch of 1.42857142857143 teeth per mm.
[21:13:15] -!- mhaberler [[email protected]] has joined #linuxcnc
[21:13:24] <gene77> I thought the G21 would make it do those calcs in mm, but apparently not.
[21:13:32] -!- jd896_laptop [[email protected]] has joined #linuxcnc
[21:13:41] <andypugh> It probably does. But what does your code do?
[21:15:04] <gene77> I wrote it in inches, it takes some input figures and calculates all the vars g76 runs with
[21:15:53] <gene77> I'll try the other non-metric entries just for S&G, brb
[21:16:45] <andypugh> So, what number did you put in for the pitch?
[21:18:34] <gene77> .7 originally, i just tried the 36,etc and g76 spits out k must be greater than j error.
[21:18:55] <gene77> so i'll try tge 1.42etc
[21:19:11] <andypugh> That's the most likely.
[21:19:44] <andypugh> Better still, edit the generated G-code to say 0.7
[21:20:50] <gene77> lemme see what a debug says
[21:22:14] <gene77> Ok, now I have a #<pitch>=0.7000000
[21:24:12] <gene77> looks like you hit it.
[21:24:36] -!- iwoj [[email protected]] has joined #linuxcnc
[21:25:16] <gene77> I'll let it complete & check the fit, too tight, run x to 0.002 & touch off, repeat till it fits
[21:35:47] <andypugh> I keep meaning to write a "tweak thread" routine, to save watching it cut air for 5 minutes.
[21:35:52] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has parted #linuxcnc
[21:39:28] <frallzor> name a good Al alloyr for machining
[21:39:33] <frallzor> * -r
[21:39:51] <syyl_> one with lead in it
[21:40:27] <gene77> Andy, I've done that for those encoder wheels. Interesting side effects of the code doesn't do things in the right order. :)
[21:42:12] <andypugh> Seems like Ray Bradbury has finished writing :-(
[21:42:38] <djdelorie> Asimov's death didn't stop his books...
[21:44:01] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has joined #linuxcnc
[21:46:28] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has parted #linuxcnc
[21:54:02] <gene77> That is another pair of shoes that go on the top shelf, alongside Clark's & Smiths
[21:55:29] <gene77> And I just found you can't raise the cutting spindle speed, the bits lag varies & the bottom of the thread groove widens.
[21:56:06] <Tom_itx> when you touch off your tools one will have a zero offset. Does it need to be called from the program or just set in the table? I was considering using a 'dowel pin' like we used to do to set up the fixture offsets and zero for the tool offsets and sticking it high up in the tool table then referencing all the other tools from that.
[21:56:52] -!- mhaberler has quit [Quit: mhaberler]
[21:56:57] <Tom_itx> or does the zero offset tool need to be called in the program or does it need to be the first tool called?
[22:00:23] -!- _abc_ has quit [Ping timeout: 244 seconds]
[22:00:28] -!- rob_h [[email protected]] has joined #linuxcnc
[22:02:40] -!- mhaberler [[email protected]] has joined #linuxcnc
[22:03:22] <gene77> Yup, I slowed the spindle back down to where I started and that is cleaning up the bottom of the threads. Purty even.
[22:04:43] -!- dimas has quit [Ping timeout: 252 seconds]
[22:05:43] <andypugh> Hilarious: Internet Explorer can't open the site htttp://uk.msn.com/ (that being the default homepage for a new install of XP)
[22:07:00] <gene77> I'd bet that is a flame worm hijacked site then.
[22:07:29] <Tom_itx> i get a picture of the queen
[22:07:33] <Tom_itx> it loaded here
[22:08:02] <Tom_itx> ie7
[22:09:01] <andypugh> Yes, I think it struggles with IE6 then.
[22:09:20] <andypugh> Not that I actually care, you understand.
[22:09:29] <Tom_itx> me either, i quit using it
[22:09:51] -!- jd896_laptop has quit [Quit: ChatZilla 0.9.88.2 [Firefox 12.0/20120420145725]]
[22:10:03] <andypugh> I don't really use Windows.
[22:10:12] <gene77> Got it Andy, perfect fit, maybe enough room for some locktite or superglue
[22:10:24] <gene77> Thanks. A bunch.
[22:10:33] <andypugh> But I am submitting a new version of an old DesignSpark PCB, so rather than try to learn gEDA...
[22:10:44] -!- mhaberler has quit [Quit: mhaberler]
[22:13:41] -!- skunkworks has quit [Ping timeout: 248 seconds]
[22:14:07] <andypugh> Would you expect a PC to do anything at all with no memory and no drive? Just wondering, like.
[22:14:43] <andypugh> I get a new DN2800MT today. It's remarkably thin. But I forgot to buy any memory for it.
[22:15:01] <andypugh> (got, not get).
[22:15:19] <andypugh> But I couldn't resist seeing if my wall-wart had the oomph to run it.
[22:17:28] <andypugh> In other news I bought a totem-pole opto for making a PWM-voltage converter today. Soon I should have PC control of the mill spindleon the new machine.
[22:20:54] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has joined #linuxcnc
[22:21:10] -!- iwoj has quit [Ping timeout: 260 seconds]
[22:25:52] <Tom_itx> it might get thru post
[22:26:18] <Tom_itx> run off 12v?
[22:28:12] -!- mhaberler [[email protected]] has joined #linuxcnc
[22:28:27] <andypugh> Yes
[22:29:05] -!- iwoj [[email protected]] has joined #linuxcnc
[22:31:09] <andypugh> I wonder if this would hold my controller PC box? http://www.tesco.com/direct/tesco-lcd-8i-10-to-23-inch-tilt-swing-tv-bracket-wall-mount/208-7351.prd?skuId=208-7351&pageLevel=
[22:31:54] <Tom_itx> one of the heavy duty ones would
[22:32:03] <Tom_itx> dunno what mount size that is
[22:32:26] <Tom_itx> that one looks a bit light maybe
[22:32:43] <Tom_itx> find one for over 23"
[22:33:00] <Tom_itx> they would be heavier and have the larger mount
[22:34:00] <Tom_itx> you could always weld one up from some square tubing
[22:34:12] -!- RussianKid has quit [Remote host closed the connection]
[22:34:54] <andypugh> Bathroom scales say that my PC is 2st6.5lbs
[22:34:55] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has joined #linuxcnc
[22:34:58] -!- skunkworks [[email protected]] has joined #linuxcnc
[22:35:01] <andypugh> (Metric? me?)
[22:35:29] -!- mozmck has quit [Ping timeout: 250 seconds]
[22:35:40] -!- RussianKid has quit [Remote host closed the connection]
[22:36:19] <andypugh> Which is about 16kg. But likely to be a lot further from the bracket than in the case of a TV
[22:36:25] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has joined #linuxcnc
[22:36:44] <Tom_itx> it may hold it..
[22:37:21] <Tom_itx> why do you need the pc on a mount and not just maybe the monitor and keyboard?
[22:37:36] <andypugh> Yes, but I think prodding the buttons and screen might lead to wobbles.
[22:37:43] -!- frallzor has quit []
[22:38:24] <andypugh> It's all one unit. https://picasaweb.google.com/108164504656404380542/CNCUnsorted#5586611443242826466
[22:40:20] <Tom_itx> what interface is that?
[22:40:32] <andypugh> Touchy
[22:40:43] <Tom_itx> is that strictly for touch screens?
[22:40:51] <andypugh> Yes, really.
[22:41:05] <andypugh> It works with a mouse.
[22:41:09] <Tom_itx> i'd have one but the display got cracked in shipping
[22:41:25] <Tom_itx> i had a spare touch pad to replace it with but not the lcd
[22:43:07] <Tom_itx> http://tom-itx.dyndns.org:81/~webpage/SBC/lcd_spot.jpg
[22:44:10] <andypugh> Vaguely pretty, if annoying.
[22:44:16] <Tom_itx> heh
[22:44:18] <Tom_itx> yeah
[22:44:29] <Tom_itx> i tried to find an lcd surplus here but no luck
[22:44:47] <theorbtwo> Humans aren't terribly good at using touch screens that are vertically in front of them. Much better when flat or at a slight angle, which will mean that the screen / computer has more leverage on the mount then otherwise.
[22:44:55] <Tom_itx> i should have gotten the other ones they had but didn't have the cash at the time
[22:44:58] <theorbtwo> That's actually quite pretty!
[22:45:16] <Tom_itx> 3 or 4 17" touch monitors for ~$65 ea
[22:50:54] <andypugh> theorbtwo: I have noticed that, but it is just something I will get used to, I think.
[22:51:22] <andypugh> I have the option of plugging in a keyboard at least.
[22:51:57] <Jymmm> Tom_itx: lcd monitor or for laptop
[22:52:42] <Tom_itx> it was on a gps tracking system for a fleet
[22:52:45] <Jymmm> Tom_itx: I have a source for NEW replacement lcd panels
[22:53:03] <Tom_itx> it's ok
[22:53:09] <Jymmm> k
[22:53:58] <Tom_itx> it was LVDS though
[22:54:30] <Jymmm> i found a pretty decent packaged curry today
[22:54:44] <Tom_itx> when i got it the hope was to use it on the cnc but not now
[22:54:59] <Tom_itx> it was free anyway, just paid the shipping
[22:56:30] <Tom_itx> along with 5 or 6 of these: http://tom-itx.dyndns.org:81/~webpage/SBC/inside_control.jpg
[22:57:07] <Jymmm> what is it?
[22:57:41] <Tom_itx> PC104 with a rabbit controller and gps
[22:57:51] <Tom_itx> it was the tracking system
[22:57:53] <Jymmm> k
[22:58:11] <Tom_itx> really too slow to be useful for much
[23:00:52] -!- RussianKid [RussianKid!~sasha@cpc7-nott15-2-0-cust136.12-2.cable.virginmedia.com] has parted #linuxcnc
[23:07:49] -!- mhaberler has quit [Read error: No route to host]
[23:08:16] -!- mhaberler [[email protected]] has joined #linuxcnc
[23:09:40] -!- rob_h has quit [Read error: Connection reset by peer]
[23:10:03] -!- rob_h [[email protected]] has joined #linuxcnc
[23:14:07] <Jymmm> Name crunchy food that doens't come out of a bag, ready GO!
[23:14:49] <syyl_> http://en.wikipedia.org/wiki/Pringles
[23:15:10] <Jymmm> heh
[23:15:15] <syyl_> :D
[23:15:18] <Jymmm> not what I meant, but ok =)
[23:15:32] <Tom_itx> chocolate covered bugs
[23:15:45] <Jymmm> I was trying to avoid the whole "chip" thing
[23:15:53] <syyl_> i knew ;)
[23:16:01] <Jymmm> Tom_itx: comes in a bag?
[23:16:11] <Tom_itx> couldn't tell you
[23:16:18] <Jymmm> heh
[23:16:20] <Tom_itx> never plan to be able to either
[23:16:25] <andypugh> Toffee
[23:16:37] <syyl_> burned steak
[23:16:49] <Jymmm> syyl_: NEVER
[23:16:56] <Tom_itx> celery
[23:17:00] <Jymmm> med rare
[23:17:14] <Tom_itx> carrots
[23:17:15] <Jymmm> carrots
[23:17:22] <Jymmm> crackers
[23:17:25] <andypugh> Apples
[23:17:38] <Jymmm> dried fruit/veggies
[23:17:47] <Jymmm> dried shrimp (ew)
[23:17:53] <andypugh> Dried banana especially.
[23:18:15] <Jymmm> andypugh: mini yellow hockey pucks
[23:18:30] <Jymmm> cookies
[23:18:52] <Jymmm> french fries, tator tots, hash browns,
[23:19:00] <Tom_itx> soggy
[23:19:16] <Jymmm> Tom_itx: If soggy, you're getting them from the wrong place =)
[23:20:14] <Tom_itx> mickee dees??
[23:20:20] <Jymmm> anything else? I've run out of ideas
[23:20:28] <Jymmm> pretzels I guess
[23:20:43] <Jymmm> Tom_itx: Oh, then get them fresh.
[23:20:57] <syyl_> a good full size pretzel issnt crunchy
[23:20:59] <Jymmm> garlic bread / toast
[23:21:14] <Jymmm> syyl_: True
[23:21:16] <syyl_> trust me, we bavarians know our pretzels :D
[23:21:51] <Jymmm> tempura? not really, sorta kinda.
[23:22:05] <Jymmm> blanched veggies
[23:22:52] <Jymmm> For the hell of it, I've given up meat for the month of June. But that kinda limits your choices of things.
[23:23:40] <Jymmm> and everything is mooshy so I have a crunchy craving!!!
[23:24:11] <Jymmm> and I can only eat so many radishes =)
[23:25:41] <andypugh> Pizza with sun-dried tomatoes. It's not crunchy, but its great.
[23:26:26] <Jymmm> pizza is good
[23:27:10] <Jymmm> I am eating eggs and dairy, just not real meat.
[23:27:40] <andypugh> Fallafel and Salad is OK, there is a bit of crunch in the lettuce. Add picked betroot for dripping-blood substitute.
[23:27:53] <andypugh> (pickled)
[23:28:14] <Jymmm> andypugh: sun dried tomatoes, frech spinache, zuccini
[23:28:19] <Jymmm> pickled what?
[23:28:25] <andypugh> beetroot
[23:28:46] <Jymmm> never seen beetroot, just beets
[23:29:04] <Jymmm> or is that he brit equiv?
[23:29:07] <Jymmm> the
[23:29:09] <andypugh> Not really.
[23:29:11] <andypugh> http://www.lovebeetroot.co.uk/
[23:29:12] <Jymmm> k
[23:29:52] <andypugh> Extremely red?
[23:30:09] <Jymmm> andypugh: Yeah, we just call them beets here in the states
[23:30:28] <Jymmm> andypugh: and the tops would be called "Beet greens"
[23:30:44] <Jymmm> mustard greens, collard greens, etc
[23:30:48] <andypugh> Right.
[23:30:54] <ve7it> beet-root, beet-top....
[23:31:04] <andypugh> "Beet" to me means sugar beet, or animal fodder.
[23:31:56] <Jymmm> pickled beets is what tey would be labeled as in the us
[23:31:58] <Jymmm> US
[23:32:11] <Jymmm> we have a few jars of them =)
[23:32:22] <Jymmm> pickled ginger is great!!!
[23:32:56] <andypugh> I would have put you a long way down the list of "folks most likely to give up meat for a month"
[23:33:13] <Tom_itx> heh
[23:33:45] <Tom_itx> sweet potato fries aren't bad
[23:33:54] <Jymmm> andypugh: I don't even know what gave me the idea actually. It wasn't any outside influence or anything, just figured I'd try something different is all.
[23:34:03] <Jymmm> Tom_itx: bags of em in the freezer.
[23:34:15] <andypugh> I did the same thing, about 5 years ago...
[23:34:27] <Jymmm> oh hang on, let me get the bag of something...
[23:34:29] <Tom_itx> no meat at all?
[23:34:52] <andypugh> Anyway, time to log off.
[23:34:57] <andypugh> Night all.
[23:35:01] <Tom_itx> night andypugh
[23:35:04] -!- andypugh has quit [Quit: andypugh]
[23:35:06] <Jymmm> night anonimasu
[23:35:12] <Jymmm> and andy too
[23:35:39] <Tom_itx> no meat at all?
[23:35:51] <Jymmm> These are AWESOME http://www.freshgourmet.com/freshgourmet/retail/product_details.asp?type=crunchy_toppings&id=72
[23:36:14] <Jymmm> Found them at Smart and Final, in the produce area.
[23:36:18] -!- alex4nder has quit [Ping timeout: 245 seconds]
[23:36:37] <Jymmm> real strong ginger flavor
[23:38:11] -!- alex4nder [[email protected]] has joined #linuxcnc
[23:41:23] <Jymmm> peanuts are crunchy!
[23:42:32] <alex4nder> hey
[23:42:37] <Jymmm> ho
[23:42:43] <alex4nder> sup Jymmm
[23:43:02] <Jymmm> alex4nder: crucnhy foods that dont come in a bag
[23:43:15] <alex4nder> nice
[23:43:27] <alex4nder> laf
[23:43:43] <alex4nder> I'm surprised I haven't gotten any feedback on the axis patch I double posted to the mailing list.
[23:43:51] <Tom_itx> did you give up bags as well as meat?
[23:44:15] <Jymmm> Tom_itx: bag == potato/tortilla chips
[23:54:14] <Tom_itx> ok, well i'm gonna have some chips anyway
[23:55:16] <Jymmm> go for it =)
[23:56:35] <alex4nder> ok
[23:56:59] <alex4nder> anyone feel like reviewing and pushing my change into the tree?