Back
[00:06:07] -!- jpk has quit [Ping timeout: 240 seconds]
[00:08:47] -!- rob_h has quit [Ping timeout: 240 seconds]
[00:22:33] -!- mhaberler has quit [Quit: mhaberler]
[00:26:26] -!- FinboySlick [[email protected]] has joined #linuxcnc
[00:26:46] -!- atom1 [[email protected]] has joined #linuxcnc
[00:26:46] -!- atom1 has quit [Changing host]
[00:26:47] -!- atom1 [atom1!~tom@unaffiliated/toml/x-013812] has joined #linuxcnc
[00:29:16] <atom1> jthornton,
http://www.youtube.com/watch?v=SGuV86Su430&feature=youtu.be
[00:30:11] <jdh> speedy probing
[00:30:39] <Tom_itx> that was one of the parts we ran on the little Okuma Kadet i happened to find in my drawer
[00:31:19] <jdh> I need a probe.
[00:40:40] <cradek> heh I recognize that circle probe routine
[00:40:47] <cradek> I've seen it a few times before
[00:41:08] <cradek> you'll never go back to not having a probe once you get used to one
[00:41:38] <Tom_itx> did you write it?
[00:41:42] <Tom_itx> it works good
[00:42:08] <cradek> yes
[00:42:32] -!- mhaberler [[email protected]] has joined #linuxcnc
[00:43:04] <Tom_itx> would it be hard to have it move down in z to the bottom then raise up say .2" and start probing?
[00:43:19] <Tom_itx> probably not
[00:43:35] <cradek> of course not
[00:43:56] <Tom_itx> i haven't written cod with vars yet
[00:44:00] <Tom_itx> code*
[00:47:41] -!- andypugh has quit [Quit: andypugh]
[00:47:42] <cradek> the exact probe touch location is stored, I think Z is in 5063, so you just g90 g0 z[#5063+0.2] or whatever
[00:48:09] <cradek> so easy
[00:49:25] <Tom_itx> what is that very short z move at the start for?
[00:49:54] <Tom_itx> G91 G38.3 z.00001
[00:50:26] <cradek> I don't remember. looks like a way to get the current position loaded
[00:50:35] <cradek> into those probe result variables
[00:50:44] <Tom_itx> i wondered about that
[00:51:18] <Tom_itx> how long are the variables visible?
[00:51:31] <Tom_itx> are they stored in a file or just ram?
[00:51:48] <cradek> they are not stored on disk by default, although I think you could make them do that if you wanted to
[00:51:55] <Tom_itx> ok
[00:52:09] <cradek> I think if you add lines for those numbers to the var file they would become persistent (untested)
[00:52:10] <Tom_itx> just write them back to a fixture offset?
[00:52:14] <Tom_itx> like G54
[00:52:31] <cradek> sure you could feed them into G10 to set G54 etc, and then that is persistent
[00:52:47] <cradek> "probe the left edge and set G54 there" is a useful type of program to use
[00:53:03] <Tom_itx> yup
[00:56:38] -!- nandoP has quit [Quit: nandoP]
[01:00:17] -!- atom1 has quit [Quit: Leaving]
[01:03:21] -!- davec_ [[email protected]] has joined #linuxcnc
[01:14:57] -!- Brandonian has quit [Quit: Brandonian]
[01:15:58] -!- geo01005_ [[email protected]] has joined #linuxcnc
[01:16:48] -!- Brandonian has quit [Client Quit]
[01:19:59] -!- geo01005 has quit [Ping timeout: 268 seconds]
[01:20:08] geo01005_ is now known as geo01005
[01:22:42] -!- djinni` has quit [Quit: ERC Version 5.3 (IRC client for Emacs)]
[01:22:42] -!- mal``` has quit [Quit: ERC Version 5.3 (IRC client for Emacs)]
[01:23:29] -!- zzolo has quit [Client Quit]
[01:24:28] -!- djinni` [djinni`[email protected]] has joined #linuxcnc
[01:33:43] -!- nots_ has quit [Ping timeout: 244 seconds]
[01:35:24] -!- geo01005 has quit [Ping timeout: 268 seconds]
[01:53:27] -!- jthornton_ [[email protected]] has joined #linuxcnc
[01:53:28] -!- jthornton has quit [Read error: Connection reset by peer]
[01:53:28] -!- john__ [[email protected]] has joined #linuxcnc
[01:53:28] -!- JT-Shop has quit [Read error: Connection reset by peer]
[01:57:04] -!- mhaberler has quit [Quit: mhaberler]
[01:59:57] <skunkworks__> http://youtu.be/U61ub6mtpH4
[01:59:57] <skunkworks__> :)
[02:00:39] <skunkworks__> I have used all those routine... they work great
[02:01:50] <skunkworks__> logger[psha]:
[02:03:02] <skunkworks__> * just remember to put the correct probe diameter in the routines. ;)
[02:05:10] <ssi> Connor: you around?
[02:06:19] <jdh> he's out, looking for more motors to destroy.
[02:06:24] <ssi> lol
[02:08:22] <ssi> I was reading through the (considerable) backlog on the Hoss G0704 thread, and I noticed something about him making plastic parts for a conversion for Connor
[02:08:26] <ssi> wondering how that worked out
[02:08:32] <ssi> I'm printing some parts from hoss's models now, for giggles
[02:08:49] <jdh> are you sure about that?
[02:08:59] <ssi> I'm rarely sure about anything
[02:09:24] <jdh> connor made some stepper covers. Hoss then 3d printed some.
[02:09:35] <ssi> I see
[02:10:17] -!- geo01005 [[email protected]] has joined #linuxcnc
[02:11:28] <jdh> http://tinyurl.com/9zkg7qh
[02:11:34] <jdh> they look like that.
[02:11:50] <jdh> except they really look better than my crappy phonecam shows
[02:12:07] <ssi> yea I just found the stl of them
[02:12:15] <jdh> hoss's?
[02:12:19] <ssi> are those 3d printed or machined or injection molded or what
[02:12:22] <ssi> yea hoss's model
[02:12:33] <jdh> hoss printed them. Connor milled his.
[02:12:38] <ssi> gotcha
[02:12:40] <jdh> (and mine)
[02:12:48] <ssi> aluminum?
[02:12:54] <jdh> PVC 'lumber'
[02:12:57] <ssi> ohhh
[02:12:58] <ssi> neat
[02:14:20] <ssi> https://p.twimg.com/AzvdYw4CEAAX4hb.jpg:large
[02:18:14] -!- null_radix has quit [Remote host closed the connection]
[02:22:53] <ink_> http://rt.com/news/nasa-concept-submarine-spacesuit-091/
[02:23:08] <ink_> 3d-printing space ships :o
[02:23:47] <ssi> Printable spacecraft, a Phase II project of apparent simplicity, builds an unbelievable picture of uploading a designed spacecraft from your laptop to a printer and collecting it later in the day from the output tray.
[02:23:54] <ssi> awesome idea, but if they can do it in under a day I'll eat my hat
[02:23:56] <ssi> :D
[02:24:02] <ink_> hehe
[02:24:14] <jdh> I ran across that thread about printing parts for him, different than what I was thinking of.
[02:24:54] <ssi> I was mostly just curious to see if he was using plastic motor mounts on his machine
[02:25:12] <ssi> I'm planning to get it running with the plastic mounts and then use the machine to make aluminum mounts for itself
[02:25:20] <ssi> I could just do them on my manual mill but I'm super lazy :P
[02:25:44] <jdh> I made my initial mounts out of Delrin on my router. Then used the g0704 to make them out of aluminum
[02:27:18] <jdh> My Z ballnut mount is still Delrin. I need to remake it in Aluminum. There is a little flex in the current one.
[02:27:22] <ssi> I kinda want to make this machine all servo at some point
[02:27:31] <ssi> I have drives for it, but only one servo so far
[02:27:52] <ssi> might do the servo on Z and two 381oz steppers on X/Y
[02:27:59] <ssi> since I only have two steppers on hand
[02:28:15] <jdh> steppers are cheap
[02:28:34] <jdh> I have a 2:1 570oz on my Z. Plenty fast enough
[02:28:38] <ssi> where's your sense of adventure?!
[02:28:59] <Tom_itx> jdh that should give you lots of torque
[02:29:05] <jdh> I'd much prefer servos, just cost prohibitive
[02:29:17] <ssi> well like I said, I already have the drives
[02:29:28] <ssi> they're crazy overkill drives too
[02:29:31] <ssi> 80V/30A
[02:29:38] <jdh> http://www.monoprice.com/products/product.asp?c_id=109&cp_id=10828&cs_id=1082808&p_id=5560&seq=1&format=2
[02:29:41] <jdh> <urk>
[02:31:44] <ssi> oooo
[02:31:45] <ssi> http://www.ebay.com/itm/Bridgeport-Interact-412-Servo-Motors-/160858622484?pt=BI_Mills&hash=item2573ebca14#ht_1280wt_1413
[02:31:48] <ssi> speaking of overkill
[02:35:20] <ssi> was actually thinkign something around this neighborhood
[02:35:21] <ssi> http://www.ebay.com/itm/NEW-MCG-DC-Servo-Motor-with-Renco-5000-count-encoder-/280846901483?pt=LH_DefaultDomain_2&hash=item4163c7a0eb#ht_1950wt_1413
[02:36:07] -!- Keknom [[email protected]] has joined #linuxcnc
[02:45:15] -!- _bwg_ has quit [Quit: Bye!]
[02:53:21] -!- demacus_ has quit [Read error: Operation timed out]
[03:02:21] <skunkworks__> hope he is not calibrating with the indicator at that angle..
[03:02:23] <skunkworks__> http://www.youtube.com/watch?v=yhuSH0sYBrw
[03:04:22] <ssi> lol
[03:06:24] -!- demacus_ [[email protected]] has joined #linuxcnc
[03:06:46] <Jymmm> skunkworks__: Why not, it's a "PERFECT" 0.1" =)
[03:07:36] <Tom_itx> it's a smart dial... the angle is calculated in the result
[03:09:19] -!- geo01005_ [[email protected]] has joined #linuxcnc
[03:09:51] -!- geo01005 has quit [Ping timeout: 244 seconds]
[03:09:59] geo01005_ is now known as geo01005
[03:11:51] <ssi> so picky!
[03:14:49] <L84Supper> calibration?
[03:14:49] <mozmck> this looks like a deal!
http://www.ebay.com/itm/Bridgeport-Discovery-308-/290753700920?pt=BI_Mills&hash=item43b2456438
[03:15:38] <ssi> indeed
[03:16:01] <L84Supper> except for being in Texas, it's a deal
[03:16:14] <mozmck> I'm fighting my bidding urge... It's only a 4 hour drive from me!
[03:16:23] <mozmck> and I'm in Texas too!
[03:16:36] <ssi> gogogogo
[03:16:39] <mozmck> No mention of loading though.
[03:16:43] <L84Supper> nobody is perfect :)
[03:17:18] <ssi> looks like a good machine for a conversion
[03:17:21] <mozmck> I'm going through Austin this weekend too! argh!! it's killing me!
[03:17:27] <ssi> I'm looking for something like that myself
[03:17:35] <ssi> some kind of ancient VMC with a crap control that's cheap
[03:17:41] <L84Supper> have a truck or trailer?
[03:17:45] <ssi> sorta like the HNC I got... a nice machine with a bad old control
[03:17:48] <mozmck> both.
[03:17:56] <ssi> what's the discovery weigh?
[03:18:06] <L84Supper> why not? (just do it)
[03:18:07] <mozmck> This one says it is working. about 6000lb on this machine.
[03:18:19] <mozmck> No money :(
[03:18:30] <L84Supper> worst case is you'll fix and sell it
[03:18:37] <ssi> haha don't let that stop ya
[03:18:44] <mozmck> And it's not even broke!
[03:19:16] <L84Supper> it's always how it works.......
[03:19:23] <mozmck> I might have to borrow a trailer for that weight. Would look funny going to a wedding with that on a trailer!
[03:19:40] <ssi> it's just beyond the capacity of my forklift... might have to remove some parts :)
[03:19:46] <Connor> jdh, ssi: Yea, Hoss was going to print out some stepper mounts for me.. but, I never got them.. Too late now.. That was before I had my conversion done.
[03:19:47] <Connor> But, Now, I have plenty of time to contemplate.. and save $$ to buy material for my next steps..
[03:20:00] <ssi> Connor: gotcha
[03:20:05] <ssi> Connor: I'm working on printing mounts from his models now
[03:20:14] <ssi> I could have modeled it myself, but I don't have to :P
[03:20:47] <Connor> Ditto. Nothing he's done is really overly complicated... He just documents everything very well.
[03:21:06] <L84Supper> mozmck, you'd be surprised what a few ribbons, a glue gun and some glitter can do
[03:21:08] <ssi> I dunno about "very well"
[03:21:12] <ssi> but more than zero, yes :)
[03:21:53] <ssi> have a Y spacer printed, and Y mount is just about finished
[03:21:57] <ssi> I'll kick off the X mount before I go to bed
[03:22:27] <Connor> jdh: You going to reorder your 1.5" CRS bar ?
[03:26:39] <L84Supper> http://www.ebay.com/itm/1999-Bridgeport-Series-I-2-HP-Vertical-Milling-Machine-DRO-P-F-48-Table-/170888668685?_trksid=p4340.m1982&_trkparms=aid%3D555001%26algo%3DPW.CURRENT%26ao%3D1%26asc%3D7%26meid%3D1172136011976197677%26pid%3D100009%26prg%3D1004%26rk%3D5%26 is a newer Bridgeport really worth this?
[03:31:28] -!- nots [[email protected]] has joined #linuxcnc
[03:37:28] -!- cevad has quit [Quit: Leaving]
[03:40:26] -!- sumpfralle1 has quit [Ping timeout: 246 seconds]
[03:53:40] -!- Guthur has quit [Remote host closed the connection]
[04:00:07] <elmo40> L84Supper: no.
[04:00:16] <elmo40> takes 3phase.
[04:00:21] <elmo40> only R8 taper
[04:00:43] <ssi> a li'l 3phase never hurt nobody
[04:08:49] <toastyde1th> L84Supper, depends on what you mean
[04:08:51] <toastyde1th> to a hobbyist, no
[04:08:54] <toastyde1th> to a business, yes
[04:09:00] <elmo40> not at all
[04:09:01] <elmo40> R8?
[04:09:07] <elmo40> not versatile enough
[04:09:19] <elmo40> that 2Hp machine should be a CAT holder
[04:09:20] <toastyde1th> r8 is plenty versatile
[04:09:59] <toastyde1th> and is much faster changing tools for manual machines than CAT is
[04:10:29] <elmo40> now there is an interesting phrase... 'faster changing tools' with 'manual machines'.
[04:10:32] <elmo40> who cares
[04:10:51] <elmo40> your not making 10,000 widgets on that thing with 5 tool changes
[04:10:57] <toastyde1th> i do, because I don't want to fuck around with wrenches and a changing block when I'm using a tiny machine
[04:11:25] <elmo40> what wrenches? pneumatic draw bar FTW. We have 2. work well.
[04:11:26] <toastyde1th> there's no reason to have cat on a bridgeport and never will be
[04:11:35] <toastyde1th> if you give a shit, don't use a bridgeport
[04:11:44] <elmo40> same tooling that is in our smaller CNC machines
[04:12:02] <elmo40> everything works well together
[04:12:47] <toastyde1th> yeah, and it works just as well with r8
[04:12:52] <toastyde1th> because it's a bridgeport
[04:13:12] <elmo40> meh
[04:13:16] <toastyde1th> the spindle taper is quite possibly the dumbest thing i've ever heard anyone caring about on a knee mill
[04:13:57] <toastyde1th> if you like having homogeneous toolholding, that's fine - saves the shop money
[04:14:53] <elmo40> CAT40 isn't humungous. our CAT50's are! Damn they are heavy!
[04:14:55] -!- tjb1 [[email protected]] has joined #linuxcnc
[04:14:58] -!- FinboySlick has quit [Quit: Leaving.]
[04:15:25] <elmo40> lol. sorry. read that wrong ;) Talking about same holders, not size... lol
[04:18:11] -!- tjb1 has quit [Client Quit]
[04:32:02] -!- dhoovie [[email protected]] has joined #linuxcnc
[04:50:21] GeorgeH is now known as GeorgeH-Away
[05:04:12] -!- Fox_Muldr has quit [Ping timeout: 265 seconds]
[05:05:47] -!- Fox_Muldr [[email protected]] has joined #linuxcnc
[05:11:59] -!- karavanjo has quit [Read error: Connection reset by peer]
[05:13:44] -!- tjb1 [[email protected]] has joined #linuxcnc
[05:13:50] -!- john__ has quit [Read error: Connection reset by peer]
[05:15:31] -!- tjb1 has quit [Client Quit]
[05:19:34] -!- psha[work] [psha[work][email protected]] has joined #linuxcnc
[05:37:57] <Jymmm> Why would I create a circle with arcs over beziers?
[05:43:24] <KimK> Jymmm: "over" as in "in preference to"? "over" as in "guided by"? Sorry, I'm not clear what you mean.
[05:44:22] <Jymmm> preference
[05:44:35] <Jymmm> s/over/instead of/
[05:45:04] <Jymmm> what benefit is there to one versus the other?
[05:45:12] <KimK> OK. Because arcs let you specify a perfect circle with one command?
[05:45:32] <Jymmm> what about speed?
[05:46:17] <Jymmm> and it would be either 4 arc or 4 bezier to make one circle.
[05:46:55] <KimK> For your laser? You're thinking about having to maintain a minimum speed? Maybe I'm not the guy to ask, then.
[05:47:36] <KimK> But there's always G64 P0.001, or whatever.
[05:47:53] <Jymmm> That's ok =) It's all good. not to maintain a specific speed, but to complete the job the fastets
[05:47:57] <Jymmm> fastest
[05:48:36] <KimK> Maybe try it both ways and see?
[05:49:36] <Jymmm> Well, this is an outsourced job as it's in SS, not something my lil laser can do =)
[05:50:02] <KimK> How did you get to 4-arcs (what, 90 deg each?), is that caused by some CAD package?
[05:50:17] <Jymmm> it's ok, I'm not gonna sweat the small shit
[05:50:33] <KimK> Ah, OK.
[05:50:34] <Jymmm> Yeah, exactly. it's an option 4 arcs or 4 beziers
[05:51:44] <KimK> Well, glad you've got business, anyway, that's a good thing in this economy.
[05:52:15] <KimK> Back in a bit, I'll scroll back.
[05:52:24] <Jymmm> KimK: Maybe, it's actually bringing a new product to market.
[05:52:27] <Jymmm> k
[06:08:15] -!- karavanjo has quit [Read error: Connection reset by peer]
[06:11:48] -!- [emil] [[emil][email protected]] has joined #linuxcnc
[06:11:56] -!- [emil] [[emil][email protected]] has parted #linuxcnc
[06:27:03] -!- tjb1 [[email protected]] has joined #linuxcnc
[06:27:04] -!- tjb1 has quit [Client Quit]
[06:29:47] -!- davec_ has quit [Quit: Leaving]
[06:33:10] -!- awallin has quit [Ping timeout: 250 seconds]
[06:36:36] -!- samkan [[email protected]] has joined #linuxcnc
[06:36:56] -!- samkan has quit [Client Quit]
[06:44:37] -!- automata__ [[email protected]] has joined #linuxcnc
[06:52:21] -!- DJ9DJ [DJ9DJ!~Deejay@unaffiliated/dj9dj] has joined #linuxcnc
[06:52:26] <DJ9DJ> moin
[06:53:40] -!- tjb1 [[email protected]] has joined #linuxcnc
[06:54:44] -!- karavanjo has quit [Remote host closed the connection]
[06:55:49] -!- tjb1 has quit [Client Quit]
[07:02:17] -!- tjb1 [[email protected]] has joined #linuxcnc
[07:02:17] -!- tjb1 has quit [Client Quit]
[07:04:12] <skorket> I'm still in the process of calibrating my machine, but I notice that when the feed rate is 100 (mm/min, though this is pretty meaningless without calibration) it runs well, but when I put it down to 50, it becomes much louder and I can feel the vibration in the threaded rod
[07:05:13] <skorket> so, 1) is this normal? 2) is the vibration going to be a problem for the work? 3) should I not be going so slow? 4) would this be solved by microstepping?
[07:05:37] <skorket> I would appreciate any other suggestions as well. I'm really new to all of this
[07:05:48] <Jymmm> are you half stepping now?
[07:06:10] <Jymmm> 8 or 10x microstepping wouldn't hurt.
[07:06:11] <skorket> No
[07:06:38] <Jymmm> skorket: You are going to have to be more forthcoing with info, I can't guess at what your setup is.
[07:07:39] <skorket> oh, sorry. I have a Zen toolworks 7x7 frame, I have sparkfun 400 steps/rev nema17 motors (1.7a, 3v), I have a4988 pololu drivers and an arduino running grbl
[07:07:51] <skorket> motors are being run at 24v
[07:09:48] <Jymmm> Um, so you are NOT running LinuxCNC?
[07:10:40] <skorket> this is true...I hope it's alright that I'm asking in this forum
[07:13:24] <Jymmm> Well, while there are ppl here that are overall knowledgble on CNC, this is focused on LinuxCNC. Most dont have specific info on GRBL, it's capabilities, downfalls, etc.
[07:14:32] <skorket> so you think it's a grbl issue?
[07:15:08] <Jymmm> I really have no idea. microstepping is worth a try.
[07:15:33] <skorket> alright, let me try half stepping
[07:15:41] <Jymmm> I'd try 8x
[07:15:50] -!- grummund has quit [Ping timeout: 252 seconds]
[07:19:33] -!- samkan [[email protected]] has joined #linuxcnc
[07:22:23] -!- samkan has quit [Client Quit]
[07:31:40] -!- gubarez has quit [Ping timeout: 245 seconds]
[07:33:11] -!- grummund [[email protected]] has joined #linuxcnc
[07:33:13] -!- grummund has quit [Changing host]
[07:33:13] -!- grummund [grummund!~user@unaffiliated/grummund] has joined #linuxcnc
[07:33:17] -!- skunkworks__ has quit [Ping timeout: 256 seconds]
[07:33:46] -!- skunkworks__ [skunkworks__!~chatzilla@str-bb-cable-south-3-102.dsl.airstreamcomm.net] has joined #linuxcnc
[07:34:03] <skorket> wow, I think that did it
[07:34:06] <skorket> I upped it to 16x
[07:34:49] <Jymmm> cool
[07:34:58] <skorket> it's going a lot slower too...
[07:35:19] <Jymmm> sure, I suggested 8x
[07:36:02] <skorket> so a pulse is now interpreted as being going into an intermediate microstep? aren't there problems with torque/accuracy?
[07:36:23] -!- MattyMatt has quit [Read error: Connection reset by peer]
[07:36:38] <Jymmm> not really
[07:40:24] <skorket> I'm really excited. Things are shaping up...
[07:40:55] <Jymmm> congrats
[07:41:12] <skorket> are there any repositories for gcode programs? Or a list of some standard test gcode programs?
[07:41:41] <Jymmm> In LinuxCNC there are.
[07:42:36] <skorket> link?
[07:42:53] <Jymmm> http://linuxcnc.org
[07:43:00] <skorket> ok, ok, thanks
[07:43:03] -!- gallenat0r [[email protected]] has joined #linuxcnc
[07:43:30] <Jymmm> np
[07:49:07] -!- morfic has quit [Ping timeout: 240 seconds]
[07:51:21] -!- awallin [[email protected]] has joined #linuxcnc
[07:57:20] -!- rob_h [[email protected]] has joined #linuxcnc
[07:59:53] -!- mhaberler [[email protected]] has joined #linuxcnc
[08:00:46] -!- morfic [morfic!~morfic@unaffiliated/morfic] has joined #linuxcnc
[08:09:04] -!- SuicideFunky has quit [Ping timeout: 246 seconds]
[08:09:30] -!- matt_ [[email protected]] has joined #linuxcnc
[08:09:42] matt_ is now known as MattyMatt
[08:15:39] -!- geo01005_ [[email protected]] has joined #linuxcnc
[08:16:14] -!- geo01005 has quit [Ping timeout: 244 seconds]
[08:16:19] geo01005_ is now known as geo01005
[08:21:39] -!- karavanjoW_ has quit [Quit: KVIrc 4.0.4 Insomnia http://www.kvirc.net/]
[08:26:15] -!- maximilian_h [[email protected]] has joined #linuxcnc
[08:26:15] -!- maximilian_h [[email protected]] has parted #linuxcnc
[08:34:03] -!- Valen [[email protected]] has joined #linuxcnc
[08:39:10] -!- sumpfralle [[email protected]] has joined #linuxcnc
[08:39:11] -!- sumpfralle1 [[email protected]] has joined #linuxcnc
[08:39:26] -!- sumpfralle has quit [Client Quit]
[08:40:46] -!- Vq has quit [Ping timeout: 248 seconds]
[08:41:02] -!- Vq [[email protected]] has joined #linuxcnc
[08:43:21] -!- asdfasd [[email protected]] has joined #linuxcnc
[08:52:13] -!- geo01005 has quit [Ping timeout: 245 seconds]
[09:00:02] -!- tjb1 [[email protected]] has joined #linuxcnc
[09:03:25] -!- tjb1 has quit [Client Quit]
[09:04:22] -!- logger[psha] has quit [Ping timeout: 252 seconds]
[09:05:36] -!- logger[psha] [logger[psha][email protected]] has joined #linuxcnc
[09:10:54] -!- awallin has quit [Ping timeout: 250 seconds]
[09:13:21] -!- awallin [[email protected]] has joined #linuxcnc
[09:21:02] -!- odogono has quit [Read error: Connection reset by peer]
[09:21:13] -!- Keknom has quit [Quit: Leaving.]
[09:26:16] -!- sumpfralle1 has quit [Read error: Operation timed out]
[09:32:16] <gallenat0r> for a ball screw 3000mm long, should I go for 32mm or is 25mm enough?
[09:45:37] -!- mk0 [[email protected]] has joined #linuxcnc
[09:48:15] <archivist> there are calculations for whip at rpm that may help choose
[09:49:18] <archivist> http://www.roymech.co.uk/Useful_Tables/Drive/Shaft_Critical_Speed.html
[09:49:26] <gallenat0r> thanks :)
[09:49:28] <r00t4rd3d> you got a 10' table?
[09:50:18] <gallenat0r> got no table yet, but it'll be 3000x1500mm'ish
[09:50:32] <archivist> so thicker shaft is stiffer and can rotate faster before you reach critical
[09:51:40] <archivist> but, if you rotate the nut and keep the screw stationary you can use the thinner
[09:52:05] -!- vladimirek [[email protected]] has joined #linuxcnc
[09:52:08] <archivist> choices, you have them
[09:59:15] <gallenat0r> got the spindle last week, so I'll build the table around that I think
[10:00:30] <archivist> building around available parts can be fun, that is how my 5 axis machine "evolved"
[10:00:59] <archivist> and why it is a "bit" fugly
[10:01:28] <gallenat0r> got any pics?
[10:02:18] <archivist> http://www.archivist.info/cnc/stage8/
[10:04:11] -!- vladimirek has quit [Remote host closed the connection]
[10:05:58] <gallenat0r> nice to see it evolving :)
[10:08:21] <archivist> I now look at castings in a machine with a view to re-purposing
[10:10:04] <archivist> I have a rectangular cast iron drill column that will probably become the column for the 5 axis
[10:14:24] -!- Thetawaves has quit [Quit: This computer has gone to sleep]
[10:24:01] -!- phantone [[email protected]] has joined #linuxcnc
[10:36:59] <r00t4rd3d> http://www.ebay.com/itm/150mW-650nm-655nm-660nm-Red-Lazer-Laser-Dot-Module-Diode-with-Driver-/170680798038?pt=LH_DefaultDomain_0&hash=item27bd5e4b56
[10:37:57] <r00t4rd3d> think i am going to get one of those
[10:38:24] <r00t4rd3d> then i can burn stuff
[10:42:55] <r00t4rd3d> http://www.ebay.com/itm/NEW-650nm-655nm-660nm-Red-250mW-Laser-DOT-Diode-Module-/170679009589?pt=LH_DefaultDomain_0&hash=item27bd430135
[10:42:58] <r00t4rd3d> there we go
[10:45:03] <r00t4rd3d> i wonder how many mw you need to easily cut 1/8" plywood
[10:46:35] <r00t4rd3d> then how do you get the laser to turn on and off at the appropriate times.....
[10:47:46] <r00t4rd3d> z axis directional pin
[10:54:55] -!- oterral has quit [Quit: Leaving.]
[11:11:31] <r00t4rd3d> http://www.liveleak.com/view?i=835_1344412426
[11:11:37] <r00t4rd3d> i could see that coming a mile away.
[11:16:06] <r00t4rd3d> pilot was lucky he didnt kill them all
[11:21:43] jthornton_ is now known as jthornton
[11:33:24] <r00t4rd3d> 36 points on google , gold!~
[11:35:25] <r00t4rd3d> http://i.imgur.com/SV3kW.jpg
[11:46:58] -!- pingufan [[email protected]] has joined #linuxcnc
[11:49:09] -!- Tom_itx has quit [Ping timeout: 248 seconds]
[11:49:39] -!- servos4ever [servos4ever!~chatzilla@74-47-247-180.dr01.hnvr.mi.frontiernet.net] has joined #linuxcnc
[11:51:12] -!- zlog has quit [Ping timeout: 252 seconds]
[11:53:55] -!- zlog [[email protected]] has joined #linuxcnc
[11:54:55] -!- skunkworks__ has quit [Remote host closed the connection]
[11:56:47] -!- dhoovie has quit [Read error: Connection reset by peer]
[12:09:17] <amaldo> lall
[12:10:04] -!- geo01005 [[email protected]] has joined #linuxcnc
[12:26:55] <alex_joni> mhaberler: now I'm hungry :/
[12:27:13] <alex_joni> err that was for -devel
[12:27:57] <r00t4rd3d> thats why we still on 10.04, nothing but food talk going on over there?
[12:28:24] <archivist> alex_joni, yesterday I was moaning about my isp speed, today a letter, finally moving to adsl2
[12:29:40] <r00t4rd3d> i say we all chip in on a warehouse in kansas
[12:29:59] <jdh> would that involve living in, or visiting kansas?
[12:30:22] <r00t4rd3d> living
[12:30:41] <jdh> I'm sure there are worse places. Siberia perhaps.
[12:30:59] <r00t4rd3d> cnc machines and google fiber
[12:31:35] <jdh> have you considered actually leaving the basement and going outside sometime?
[12:32:29] <r00t4rd3d> i normally work 50 hour weeks :/
[12:32:42] <jdh> who doesn't?
[12:32:58] <r00t4rd3d> im not a basement dweller.
[12:33:47] <jdh> that was a joke
[12:34:43] <r00t4rd3d> wish i lived in the basement, alot cooler down there
[12:34:49] <r00t4rd3d> too many bugs though
[12:37:03] <r00t4rd3d> ive seen some spiders down there this year i could feed to a small african village.
[12:37:23] <r00t4rd3d> probably with seconds...
[12:38:25] -!- skunkworks [[email protected]] has joined #linuxcnc
[12:41:58] -!- pingufan has quit [Quit: Konversation terminated!]
[12:42:41] -!- Valen has quit [Quit: Leaving.]
[13:13:18] -!- FinboySlick [[email protected]] has joined #linuxcnc
[13:15:29] <alex_joni> archivist: yay
[13:15:38] <alex_joni> seems someone else is reading the lcnc logs :D
[13:16:53] -!- Farthen has quit [Excess Flood]
[13:19:18] -!- zlog has quit [Ping timeout: 245 seconds]
[13:19:25] -!- Farthen [Farthen!~Farthen@2a01:4f8:101:2a4:0:bc28:b2e1:9] has joined #linuxcnc
[13:22:12] -!- zlog [[email protected]] has joined #linuxcnc
[13:33:08] -!- BenceKovi11115 [[email protected]] has joined #linuxcnc
[13:39:59] -!- Farthen has quit [Excess Flood]
[13:40:43] -!- BenceKovi11115 has quit [Quit: Nettalk6 - www.ntalk.de]
[13:42:24] -!- Farthen [Farthen!~Farthen@2a01:4f8:101:2a4:0:bc28:b2e1:9] has joined #linuxcnc
[13:47:02] -!- Tom_itx [Tom_itx!~Tl@unaffiliated/toml/x-013812] has joined #linuxcnc
[13:49:27] -!- JT-Shop [[email protected]] has joined #linuxcnc
[14:00:00] -!- johnt [[email protected]] has joined #linuxcnc
[14:01:02] <ssi> I need to get my hands on a chuck for my HNC
[14:01:22] <ssi> and maybe a second turret top
[14:01:25] -!- johnt has quit [Client Quit]
[14:01:51] -!- johnt [[email protected]] has joined #linuxcnc
[14:06:21] -!- johnt has quit [Client Quit]
[14:08:20] <JT-Shop> in ubuntu 10.04 add to favorites fails to remember when xchat is started again. Is there a fix for this?
[14:08:20] <JT-Shop> <bviktor> yeah, erase ubuntu from all drives
[14:08:21] -!- mhaberler has quit [Quit: mhaberler]
[14:08:34] -!- micges [[email protected]] has joined #linuxcnc
[14:08:35] <JT-Shop> what quality help you get in #xchat
[14:10:09] <cradek> eh don't blame the whole channel
[14:10:21] <cradek> every channel has one of those
[14:11:06] <Jymmm> JT-Shop: This *IS* IRC after all, what did you expect, a cookie?
[14:11:13] <JT-Shop> I finally did get an answer from the same guy
[14:11:26] <cradek> and Jymmm proves my point
[14:11:44] <cradek> cool, so what's wrong? (what's a favorite in irc?)
[14:12:14] <JT-Shop> when you load xchat it remembers the channels you want to be in
[14:12:26] <JT-Shop> except in Ubuntu 10.04
[14:12:26] <cradek> ah
[14:13:11] <Jymmm> I wasn't being funny.
[14:13:29] <JT-Shop> they did provide instructions for getting the latest version as this one is 4 years old they said
[14:13:38] <JT-Shop> http://fpaste.org/R8Fx/
[14:13:55] <Jymmm> Most of IRC is just chaotic. Freenode is more of the exception.
[14:14:12] <JT-Shop> #xchat is in Freenode
[14:14:25] <cradek> JT-Shop: well that'll fuck up your packages and is the kind of advice given by someone with a grudge :-/
[14:14:31] <JT-Shop> I didn't expect this answer <bviktor> yeah, erase ubuntu from all drives
[14:14:39] <cradek> JT-Shop: did you try enabling backports and see if you get an update?
[14:14:50] <JT-Shop> no, I'll try that
[14:15:06] <cradek> did you find a bug report saying what version fixes the problem?
[14:15:28] <JT-Shop> I did find a bug report but no reply
[14:15:38] <cradek> ok, so it might not be fixed
[14:16:42] <cradek> THAT IS NOT TEH LATEST VERSION HURF DURF != "we fixed that in v5.6.7!"
[14:16:57] <Jymmm> JT-Shop: When layering sheets in waterjet, the abrasive has a hard time getting where it needs to be.
[14:17:26] <JT-Shop> ok, I didn't know
[14:17:39] <JT-Shop> doesn't seem to be any backports for xchat
[14:17:50] <Jymmm> JT-Shop: Me neither, just what the guy said when I inquired.
[14:18:09] <JT-Shop> can't hurt to ask
[14:18:18] <Jymmm> JT-Shop: at least when the sheets are in the 0.024" range
[14:18:59] <Jymmm> JT-Shop: Yeah. I sent off the RFQ after 5hr ago, so we'll see.
[14:19:14] <Jymmm> JT-Shop: He said laser far better in this respect.
[14:19:34] <cradek> http://freecode.com/projects/xchat/releases
[14:19:49] <cradek> if this is correct, 2.8.6 (the version in 10.04?) is from 2008 and there has been one release since then
[14:20:12] <cradek> you can see the release notes but there's not much in them
[14:20:24] <cradek> "many minor bugs were fixed" is a lousy release note :-(
[14:20:32] <JT-Shop> LOL yea
[14:20:51] <JT-Shop> the windows version went to payware
[14:21:00] <cradek> not that I haven't written it a few times!
[14:21:11] <cradek> I always knew while doing it that it was lousy.
[14:21:38] <JT-Shop> and so far xchat is the only one that seems to work with my satellite connection
[14:22:36] <JT-Shop> http://xchat.org/compiling/
[14:22:43] <cncbasher_> jt: have you try'd quassel irc ?
[14:22:51] <JT-Shop> not yet
[14:23:13] <Jymmm> I want to make a pair of adapters that would allow me to use a normal 120VAC extension cord for use with 12VDC stuff. What would be the "safest" way of wiring a 3 prog connector?
[14:23:46] <cradek> http://sourceforge.net/tracker/index.php?func=detail&aid=2083155&group_id=239&atid=100239
[14:23:55] <cradek> looks like it might be fixed in 2.8.8 released 2010
[14:24:45] <cradek> here are lucid debs a kind person built:
https://launchpad.net/~jensmaucher/+archive/ppa/+sourcepub/1163692/+listing-archive-extra
[14:24:50] -!- joe9 [[email protected]] has joined #linuxcnc
[14:24:56] <Jymmm> pos/neg == neutral/ground ???
[14:25:28] * JT-Shop bows to the google master today
[14:25:57] <cradek> heh
[14:27:08] <Jymmm> Is there such a thing as a circuit breaker that fits into a single gang box?
[14:27:21] -!- johnt [[email protected]] has joined #linuxcnc
[14:27:44] <JT-Shop> yes a panel mount circuit breaker will mount to the cover
[14:27:44] <cradek> I've definitely seen one outlet + one screw-in fuse in a single box, very old
[14:27:56] <r00t4rd3d> Jymmm, cheater breaker
[14:28:18] -!- psha[work] has quit [Quit: Lost terminal]
[14:28:20] <r00t4rd3d> http://www.handymanclub.com/Portals/0/activeforums_Attach/Breakers.JPG
[14:28:23] <r00t4rd3d> cheater on right
[14:28:28] -!- johnt has quit [Remote host closed the connection]
[14:28:35] <L84Supper> there are low cost 2 pole single breaker panels for AC disconnects
[14:29:13] <Jymmm> JT-Shop: like this ?
http://www.electronicplus.com/images/products/551601.jpg
[14:29:20] <JT-Shop> Jymmm, is this for your 12v application
[14:29:37] <JT-Shop> yea, that will work too
[14:30:02] <cradek> if it's DC you need a special type of breaker
[14:30:05] <Jymmm> JT-Shop: oh gawd no.... male/male to reverse feed from generator to circuit
[14:30:11] <JT-Shop> http://www.mcmaster.com/#standard-circuit-breakers/=irdaxn
[14:30:36] -!- mk0 has quit [Read error: Connection reset by peer]
[14:30:42] <JT-Shop> look at panel mount breakers and some are ac/dc rated
[14:31:32] <Jymmm> JT-Shop: Cool, for the DC thing I was just thinking inline fuses, but I guess a breaker would be ok.
[14:31:47] <JT-Shop> fuse would be cheaper
[14:31:56] <cradek> DC breakers are weird, rare, and expensive
[14:31:57] <L84Supper> Jymmm: did you need a single position panel as well?
[14:32:00] <cradek> yeah fuses work great
[14:32:07] <r00t4rd3d> you can use a switched outlet with fuse too
[14:32:29] <r00t4rd3d> http://www.thelumberlab.com/wp-content/uploads/2011/09/Finished_30_grit.jpg
[14:32:31] <r00t4rd3d> like that
[14:32:41] <JT-Shop> Rocker and Push-Button Style�Mount in a 1.77" Lg. � 0.85" Wd. panel cutout. Rated 240 VAC or 60 VDC. $20
[14:32:41] <Jymmm> L84Supper: for the AC, I was just going to use a single gang weatherproof box and add a dual CB.
[14:33:29] <JT-Shop> a blade type fuse holder and a fuse is cheaper
[14:35:03] <Jymmm> JT-Shop: two projects; one is DC (fuse), the other is feeding the generator into a circuit in the house using a male-to-male adapter using a weather proof box to hold circuit breakers.
[14:35:54] <Jymmm> aka ghetto transfer switch
[14:36:04] <JT-Shop> for your generator you unplugging the dryer then using a male / male cord?
[14:36:27] -!- Mourner has quit [Quit: Page closed]
[14:36:27] <jdh> I think Male/Male cords are illegal in most states.
[14:36:45] <Jymmm> JT-Shop: Well, 120VAC, but basically yes. (When I do get a 220VAC gen)
[14:36:46] <r00t4rd3d> http://www.ebay.com/itm/Bussmann-BP-SRU-BPSRU-Fuse-Outlet-/370590500791?pt=LH_DefaultDomain_0&hash=item5648ea47b7
[14:37:09] <Jymmm> jdh: correct, hense the term "ghetto transfer switch"
[14:37:41] <r00t4rd3d> that fuse outlet fits in a single gang
[14:38:05] <JT-Shop> the 120v circuit will need protection between the generator and the circuit
[14:39:27] <Jymmm> JT-Shop: (Male) =}-------[ single gang box with circuit breakers]---------------{= (Male)
[14:39:50] <JT-Shop> yea
[14:40:05] <JT-Shop> only need one breaker
[14:40:58] -!- theleafer has quit [Quit: Page closed]
[14:41:08] <JT-Shop> I guess I need to uninstall xchat 2.8.6 before 2.8.8 will install it gives me a "breaks existing package" error
[14:41:15] <Jymmm> JT-Shop: Well, since I'm mucking around where I shouldn't be, I figure it might be better to protect both neut and hot in case the house wiring is fubared.
[14:41:26] <cradek> hm, I'd expect it to just update
[14:41:47] <cradek> what's the whole message?
[14:42:10] <JT-Shop> no, Error: Breaks existing package 'xchat' dependency xchat-common (= 2.8.6-4ubuntu5)
[14:43:10] <JT-Shop> Jymmm, you just need a breaker on the hot
[14:43:10] <cradek> hmm
[14:43:30] <cradek> perhaps add the ppa, instructions here:
https://launchpad.net/~jensmaucher/+archive/ppa
[14:43:33] <JT-Shop> that was from this xchat-common_2.8.8-0ubuntu1_all.deb (1.1 MiB)
[14:43:34] <cradek> then maybe apt can fix it for you
[14:44:06] <JT-Shop> ah ok
[14:44:38] <Jymmm> JT-Shop: Right, but if someone wired the 50yo 2 prong house outlet reversed, then 'hot' may not be protected is what I was thinking.
[14:45:01] <cpresser> even debian has newer packages :)
http://packages.debian.org/squeeze/xchat
[14:45:12] <JT-Shop> the hot is protected from the source out
[14:45:59] <Jymmm> JT-Shop: But what if someoen screws up, forgets to turn off the main breaker on the house and the power returns?
[14:46:16] <L84Supper> boom
[14:46:35] <JT-Shop> the lineman you shocked will shoot you full of holes when he recovers
[14:46:48] <JT-Shop> and your generator will die from the overload
[14:46:52] <Jymmm> JT-Shop: besides that =)
[14:46:59] <cradek> yes you *really* don't want to allow that to happen
[14:47:17] <cradek> you could easily kill someone
[14:47:19] <Jymmm> JT-Shop: well, that's why I was thinking two breakers
[14:47:32] <JT-Shop> at my Dad's house I made a slider on the panel so only one breaker could be on
[14:47:43] <L84Supper> DPDT delay relay
[14:48:16] <Jymmm> L84Supper: but how do you prevent the coil from being enegized from the gen?
[14:48:29] <JT-Shop> if you connect your generator to the grid it will get pulled down and the one breaker will trip almost in an instant
[14:49:02] <JT-Shop> but like cradek said you just DON'T do that
[14:49:32] <Jymmm> JT-Shop: Ok, so having two breakers serves ZERO purpose at all in this respect? Even if wiring is reversed, etc?
[14:49:51] <JT-Shop> yea
[14:50:23] <Jymmm> JT-Shop: Ok, just doesn't "sound right" is all.
[14:50:45] <L84Supper> Jymmm: will any motor loads be running off the generator?
[14:51:04] <Jymmm> L84Supper: frig, freezer, Window AC.
[14:51:24] <Jymmm> at least one of the above.
[14:51:31] * JT-Shop goes to get a monkey pickel
[14:51:40] <Jymmm> TMI
[14:52:18] <Jymmm> L84Supper: what were you thinking?
[14:54:30] <L84Supper> you'll melt relay contacts if you just switch between generator and power co unless you manage to sync the switching near the zero crossing
[14:55:00] <L84Supper> thats another why you use a transfer switch, some delay plus guaranteed isolation
[14:55:12] <JT-Shop> Jymmm, your generator should have built in circuit protection
[14:55:57] <JT-Shop> your best thing is to just use an extension cord of proper size and plug things in you want powered up
[14:56:26] -!- zzolo has quit [Client Quit]
[14:56:44] <Jymmm> L84Supper: Oh no, I completely understand the use of a REAL transfer switch, and that what I'm doing here is pretty much one of the most stupidest things you could do. It's more of a "last ditch effort" sorta thing. Think apartment building as example.
[14:57:02] <cradek> JT-Shop: sudo add-apt-repository ppa:jensmaucher/ppa
[14:57:10] -!- geo01005 has quit [Ping timeout: 244 seconds]
[14:57:11] <cradek> JT-Shop: sudo apt-get update; sudo apt-get install xchat
[14:57:29] <JT-Shop> cradek, thanks
[14:58:27] -!- JT-Shop has quit [Quit: Leaving]
[14:59:04] <Jymmm> JT-Shop: It does and I do have three heavy duty 10ga 50ft extension cords.
[14:59:25] -!- mhaberler [[email protected]] has joined #linuxcnc
[14:59:42] -!- JT-Shop [[email protected]] has joined #linuxcnc
[14:59:49] -!- john__ [[email protected]] has joined #linuxcnc
[14:59:58] -!- JT-Shop has quit [Client Quit]
[14:59:58] -!- john__ has quit [Client Quit]
[15:00:00] <Jymmm> These even have cord-locks built into them; used mostly for stage/theatrical lighting.
[15:00:17] -!- JT-Shop [[email protected]] has joined #linuxcnc
[15:00:32] <JT-Shop> cradek, that worked thanks again
[15:01:02] <cradek> welcome, but thanks goes to Jens
[15:01:18] <Jymmm> JT-Shop: While you were MIA...
[15:01:28] <Jymmm> JT-Shop: It does and I do have three heavy duty 10ga 50ft extension cords.
[15:01:43] <JT-Shop> there you go
[15:01:45] <Jymmm> JT-Shop: These even have cord-locks built into them; used mostly for stage/theatrical lighting.
[15:02:02] <L84Supper> I'm waiting see how much fun we get into with the electrical system in China
[15:02:32] <Jymmm> JT-Shop: But, sometimes getting it to it's intended target (freezer) is difficult and can take more than 150ft
[15:03:12] -!- geo01005 [[email protected]] has joined #linuxcnc
[15:03:30] <JT-Shop> just don't open the freezer and it will be ok for quite some time
[15:04:07] <Jymmm> JT-Shop: Sure, but this wouldn't be for a 72hr outage, this would be for a longer one
[15:04:31] <JT-Shop> do you have enough gas for a longer one?
[15:04:40] <Jymmm> Yes
[15:05:05] <JT-Shop> are you positive your main breaker disconnects you from the grid?
[15:05:31] <Jymmm> JT-Shop: I haven;t opened the panel and inspected it, no.
[15:05:43] <Jymmm> (yet)
[15:06:03] <JT-Shop> you must be positive that the main breaker will disconnect you from the grid
[15:06:53] <Jymmm> JT-Shop: Sure, I completely understand that. As well as I would be feeding the grid otherwise.
[15:07:03] <JT-Shop> then cut the female end off of a cord and put a male on it and your good to go... could be shocking if you don't plug it in before running the generator
[15:07:08] <Jymmm> (in a limited fashion =)
[15:07:20] <JT-Shop> for a moment anyway
[15:07:46] <JT-Shop> does your generator use a twist lock plug?
[15:07:51] <Jymmm> JT-Shop: I could add some neon bulbs
[15:08:08] <JT-Shop> to?
[15:08:54] <Jymmm> JT-Shop: This gen, no (I wish it did), but I want to get a larger one that does.
[15:09:01] <JT-Shop> also know that only 1/2 of your panel can be powered with 120v
[15:09:09] <Jymmm> JT-Shop: like this but inline of the male/male adapter
http://topicstock.pantip.com/home/topicstock/2011/07/R10826123/R10826123-2.jpg
[15:09:27] <Jymmm> JT-Shop: Then I could see if anything was "live"
[15:09:35] <JT-Shop> ?
[15:10:10] <JT-Shop> that does tell you if your outlets are wired correctly
[15:10:40] <Jymmm> JT-Shop: Also, if anything is "live" (grid), before plugging in the gen.
[15:10:54] <jdh> you have a Gen. that only does 120?
[15:10:54] <JT-Shop> ??
[15:11:09] <JT-Shop> if anything is live you lights will be on
[15:11:10] <Jymmm> JT-Shop: What don't you understand?
[15:11:40] <Jymmm> JT-Shop: It's a safety precaution.
[15:11:42] <JT-Shop> what your trying to do with the tester or the neon bulbs
[15:12:11] <Jymmm> jdh: Small gen is a Honda EU2000i
[15:12:40] <Jymmm> JT-Shop: tester == anti-stupid
[15:12:45] <JT-Shop> might not run your freezer if too small
[15:12:53] <JT-Shop> what are you testing?
[15:13:03] <Jymmm> JT-Shop: Heh, it runs the 18K BTU AC =)
[15:13:51] <JT-Shop> what are you testing?
[15:15:00] <Jymmm> JT-Shop: Ok, what I'm doing is illegal for a reason. But if I do it anyway, I' trying to make it as safe as potentially possible. Having tester lights on the adapter saying "Hey, you have power stupid, why are you thinking of using me?" I think is A Good Thing (tm)
[15:15:26] <JT-Shop> won't the lights being on be a clue
[15:15:50] <Jymmm> JT-Shop: Maybe not, maybe a defective circuit breaker just after a power outage.
[15:16:12] <DaViruz> he means to have indicator lights in both ends of the male-male cable, so it will show on the other end if one end is plugged in to a power source
[15:16:52] * JT-Shop wonders what happens when you energize a generator with line power
[15:16:54] <DaViruz> (i believe)
[15:17:16] <jdh> My male-male cable goes from the Gen. to a disconnect. Disconnect goes to subpanel breaker.
[15:17:26] <DaViruz> best case with a three phase it will be forced in sync with the grid
[15:17:38] <DaViruz> if the phase sequence is correct
[15:17:44] <JT-Shop> Jymmm, you check the breakers, check the meter to see if it is on, turn off the main...
[15:18:09] <JT-Shop> if it is not running?
[15:18:14] -!- andypugh [andypugh!~andy2@cpc2-basl1-0-0-cust639.basl.cable.virginmedia.com] has joined #linuxcnc
[15:18:44] <jdh> I disconnect my subpanel from the breaker at the main panel. Turn off all the breakers in the subpanel, fire up the Gen, engage the disconnect. Turn the Gen. breaker on. Turn on the few breakers I want to power.
[15:18:58] <JT-Shop> yep
[15:19:49] <JT-Shop> mine is hard wired into my panel to a 60amp breaker, I pull the meter out of the bottom lugs, fire up the gen, flip the breaker on
[15:20:03] <JT-Shop> into a panel, I have 3
[15:20:42] <Jymmm> JT-Shop: you can pull the meter on your panel?
[15:20:46] <JT-Shop> every now and then I'll walk by the meter to see if it back alive
[15:21:07] <JT-Shop> sure
[15:21:19] <Jymmm> ours have a seal on them
[15:21:21] <JT-Shop> it's the only way to disconnect from the grid
[15:21:42] -!- andypugh has quit [Client Quit]
[15:21:45] <JT-Shop> cut the seal and toss in the trash... but you can't do that over there
[15:21:59] <Jymmm> =)
[15:22:43] <JT-Shop> I didn't plan on having 2000 sq ft garage/shop with 200amp service when I built the house is the reason I have to pull the meter
[15:23:15] <Jymmm> JT-Shop: when the meter-reader comes around, they dont put the seal back on?
[15:23:28] <JT-Shop> what's a meter-reader?
[15:24:01] <JT-Shop> is that like a milk-man?
[15:24:06] <Jymmm> hu-mon with a clipboard?
[15:24:22] <JT-Shop> I remember that from my childhood I think
[15:24:37] <Jymmm> JT-Shop: you have smart meter now?
[15:24:43] <JT-Shop> we are high tech and the meters are polled from the coop
[15:24:48] <JT-Shop> for years
[15:24:58] <JT-Shop> before that we had to read our own meters
[15:25:05] <Jymmm> ah
[15:25:19] <L84Supper> just wait until the Chinese start selling electricity
[15:25:24] <JT-Shop> which is great cause when it comes alive I know power is restored
[15:25:25] <Jymmm> and call it in?
[15:25:45] <JT-Shop> no you put the reading on the bill and next month you pay for it
[15:25:53] <Jymmm> ah
[15:26:09] <L84Supper> the honor system must be working well enough
[15:26:40] <JT-Shop> there all self reporting for years around here
[15:26:59] <JT-Shop> they know in a heartbeat if you have lost power
[15:27:18] <Jymmm> and if you lie and screw up, plug the mete in backwards =)
[15:27:50] * JT-Shop really should make a part or three now
[15:32:24] <jdh> make me a part.
[15:33:49] <Jymmm> jdh is now a part of the transgender theatrical presentation of Anne!
[15:33:51] <L84Supper> Jymmm: whenever we would temp in a generator we would just be sure to keep the main breaker off or pull the meter
[15:35:06] <L84Supper> for commercial where the meter is not in series with the power mains (but tied in with transformers) we would just be sure to lock the main disconnect off
[15:35:15] <Jymmm> L84Supper: Yeah, breakign the seal and pulling the meter might just be the safest way to go about it.
[15:36:28] <jdh> I'd rather my wife just flipped the breakers as written rather than try to pull a meter.
[15:37:13] <TekniQue> 15:27:42 < L84Supper> the honor system must be working well enough
[15:37:19] <TekniQue> it can't not work
[15:37:39] <Jymmm> jdh: My gen is portable, so it could be used anywhere and on unknown panels.
[15:37:45] <TekniQue> they'll send a guy randomly to do a reading for verification
[15:37:49] <L84Supper> sure, a transfer switch is the way to go ,but we are just discussing what to do temporarily in case of an emergency
[15:38:17] <TekniQue> and well, telling them wrong numbers is only borrowing the money from the power company at no interest
[15:38:41] <TekniQue> at the risk of paying a higher rate for it later
[15:38:53] <TekniQue> so it's not a very smart thing to do
[15:43:54] -!- syyl [[email protected]] has joined #linuxcnc
[15:45:13] -!- automata__ has quit [Ping timeout: 244 seconds]
[15:46:45] -!- tjb1 [[email protected]] has joined #linuxcnc
[15:51:20] <JT-Shop> a neighbor in MS shot his meter with a BB gun and would put a pine needle in to hold up the disk from turning
[15:51:30] <JT-Shop> got away with it for a while...
[15:51:40] -!- djcoin has quit [Quit: WeeChat 0.3.2]
[15:52:01] -!- gmagno [[email protected]] has joined #linuxcnc
[15:53:03] <Jymmm> lol
[15:54:07] -!- nandoP [[email protected]] has joined #linuxcnc
[15:54:17] <Jymmm> I JUST found out yesterday that pellet guns in the county are ILLEGAL due to the noise they create. If it has a suppressor on it, then that's ok.
[15:59:45] -!- tjb1 has quit [Quit: tjb1]
[16:00:16] <JT-Shop> if you shoot the pointy pellets they break the sound barrier so even the whisper like I have sounds like a .22 the flat ones are quiet...
[16:00:57] -!- nandoP has quit [Quit: nandoP]
[16:03:49] <JT-Shop> yuck! one of my tool holders is for a 10m turret not a 1/2" turret top
[16:12:41] <Jymmm> JT-Shop: "Whisper" being the model name?
[16:22:53] <JT-Shop> yea IIRC
[16:23:26] <JT-Shop> gamo whisper
[16:26:00] * JT-Shop notes that turning the back side with a boring bar in interesting
[16:33:26] -!- jthornton has quit [*.net *.split]
[16:33:26] -!- i_tarzan has quit [*.net *.split]
[16:33:26] -!- ybon has quit [*.net *.split]
[16:34:32] -!- jthornton [[email protected]] has joined #linuxcnc
[16:34:32] -!- i_tarzan [[email protected]] has joined #linuxcnc
[16:34:53] -!- jthornton has quit [Read error: Connection reset by peer]
[16:35:34] -!- jthornton [[email protected]] has joined #linuxcnc
[16:42:06] -!- Adventsparky has quit [Quit: KVIrc 4.1.3 Equilibrium http://www.kvirc.net/]
[16:44:56] -!- tjb1 [[email protected]] has joined #linuxcnc
[16:45:00] -!- i_tarzan has quit [*.net *.split]
[16:45:09] -!- i_tarzan [[email protected]] has joined #linuxcnc
[16:47:22] -!- tjb1 has quit [Client Quit]
[16:58:58] -!- IchGuckLive [[email protected]] has joined #linuxcnc
[16:59:03] <IchGuckLive> hi all B)
[17:03:07] -!- sumpfralle [[email protected]] has joined #linuxcnc
[17:05:25] -!- djcoin has quit [Ping timeout: 248 seconds]
[17:07:01] -!- phantone has quit []
[17:07:17] <JT-Shop> hi
[17:07:39] <IchGuckLive> nasa rover unfold complete
[17:09:42] -!- sendoushi [[email protected]] has joined #linuxcnc
[17:11:51] -!- geo01005 has quit [Ping timeout: 256 seconds]
[17:14:46] -!- zer0_her0 has quit [Read error: Operation timed out]
[17:17:08] -!- sendoushi has quit [Remote host closed the connection]
[17:17:32] -!- tjb1 [[email protected]] has joined #linuxcnc
[17:18:10] -!- tjb1 has quit [Client Quit]
[17:20:54] nick is now known as anick
[17:21:06] * JT-Shop starts the docking maneuver for a nap
[17:26:19] <Jymmm> You have to "PREPARE" for a nap?! Unless you might fall off a cliff or something, you just close your eyes.
[17:26:20] -!- bedah [[email protected]] has joined #linuxcnc
[17:26:40] -!- automata__ [[email protected]] has joined #linuxcnc
[17:26:57] <JT-Shop> well you have to get into napping position first then close your eyes
[17:27:20] <IchGuckLive> http://www.ustream.tv/channel-popup/nasa-hd-tv
[17:27:27] <JT-Shop> although I can nap anywhere some places are more comfortable than others
[17:27:28] <Jymmm> Not really, I can sleep anywhere, anyhow
[17:27:36] -!- tjb1 [[email protected]] has joined #linuxcnc
[17:27:48] -!- tjb1 has quit [Client Quit]
[17:28:26] <JT-Shop> I thought you couldn't sleep at night
[17:29:02] <Jymmm> Well, used to be able to sleep anywhere/anyhow that is ;)
[17:29:21] <Jymmm> pre-insomnia that is
[17:30:07] <JT-Shop> I used to nap laying on grating between two 16 cylinder 10,320 cu inch engines while they ran
[17:30:29] <Jymmm> see, there ya go... no prep, just nap
[17:39:55] -!- Guthur [[email protected]] has joined #linuxcnc
[17:46:31] -!- alex_joni has quit [Ping timeout: 250 seconds]
[17:46:35] -!- Loetmichel has quit [Read error: Connection reset by peer]
[17:47:09] -!- Loetmichel [[email protected]] has joined #linuxcnc
[17:47:09] -!- alex_joni [alex_joni!~alex_joni@emc/board-of-directors/alexjoni] has joined #linuxcnc
[17:47:10] -!- mode/#linuxcnc [+v alex_joni] by ChanServ
[17:48:52] -!- sumpfralle1 [[email protected]] has joined #linuxcnc
[17:50:12] -!- psha [[email protected]] has joined #linuxcnc
[17:52:07] -!- sumpfralle has quit [Ping timeout: 240 seconds]
[17:53:19] -!- sumpfralle1 has quit [Ping timeout: 244 seconds]
[17:55:08] -!- gmagno has quit [*.net *.split]
[17:55:08] -!- odogono_ has quit [*.net *.split]
[17:55:08] -!- RagingComputer has quit [*.net *.split]
[17:55:08] -!- SWPadnos has quit [*.net *.split]
[17:55:08] -!- kanzure has quit [*.net *.split]
[17:58:02] -!- gmagno [[email protected]] has joined #linuxcnc
[17:58:02] -!- RagingComputer [[email protected]] has joined #linuxcnc
[17:58:02] -!- SWPadnos [SWPadnos!~Me@emc/developer/SWPadnos] has joined #linuxcnc
[17:58:02] -!- kanzure [[email protected]] has joined #linuxcnc
[17:58:02] -!- mode/#linuxcnc [+v SWPadnos] by hitchcock.freenode.net
[17:59:48] -!- zzolo has quit [Quit: zzolo]
[18:00:17] <IchGuckLive> heavy posting !!
[18:00:27] <IchGuckLive> Holiday leek
[18:00:47] <IchGuckLive> wether is fine in the World beside Manila
[18:01:15] <IchGuckLive> Mexiko expecd a Strorm comming up
[18:03:10] <IchGuckLive> also tornadowatch in place at Witchita , est to lincoln
[18:04:42] <IchGuckLive> according to ->
http://www.nrlmry.navy.mil/TC.html §Storms in the atlantic 2 est pacific and 3 west pacific 13 TC in the seeseon
[18:04:54] <Tom_itx> IchGuckLive where?
[18:05:58] -!- broofa has quit [Read error: Operation timed out]
[18:05:59] <IchGuckLive> What
[18:06:09] <Tom_itx> tornadowatch in place at Witchita , est to lincoln
[18:06:30] <IchGuckLive> http://www.spc.noaa.gov/products/watch/ww0165.html
[18:06:36] <jdh> all the atlantic storms are pretty lame.
[18:06:57] <Tom_itx> IchGuckLive i haven't heard about that
[18:09:28] <IchGuckLive> 1 fire outloock
http://www.spc.noaa.gov/products/fire_wx/fwdy1.html
[18:09:43] <Tom_itx> the sky is clear here
[18:10:30] <IchGuckLive> as you say
[18:10:50] -!- sumpfralle [[email protected]] has joined #linuxcnc
[18:12:15] <IchGuckLive> have a nice day where ever you are on the planet im off BY
[18:12:26] -!- IchGuckLive has quit [Quit: ChatZilla 0.9.87 [Firefox 13.0/20120601201853]]
[18:18:58] -!- tjb1 [[email protected]] has joined #linuxcnc
[18:20:18] <joe9> need some advice, please? I have a Z (tool length probe switch). I have the X and Y position where the probe switch is at. The probing is working fine. I am trying to get the X and Y to what it was before the "probing" subroutine is called.
[18:20:39] <joe9> i see G30 and G30.1, but, that is for probing.
[18:21:07] <joe9> I need something to store the X and Y before doing the probing subroutine and after the probing, get back to that X and Y.
[18:21:10] <jdh> save the x/y before you probe
[18:21:21] <joe9> I can store the values in #5061
[18:21:25] <joe9> and #5062
[18:21:28] <joe9> as X and Y
[18:21:38] <joe9> but, not sure if there is smarter way to go about it.
[18:21:54] <joe9> jdh, X = #5061 and Y = #5062, correct?
[18:22:17] <jdh> you could save x&y as coord. offsets, but I don't think that would buy you anything.
[18:23:02] <jdh> isn't that where the probed values are stored?
[18:23:07] <joe9> yes.
[18:23:16] <joe9> how can I read X and Y values?
[18:23:19] <jdh> then it woudln't be a good place to save x&y
[18:23:31] <joe9> no, I save them in my variables
[18:23:40] <joe9> i am trying to figure out where to read them from.
[18:24:32] <jdh> you've lost me.
[18:25:01] <joe9> where are the current X and Y values stored in?
[18:25:16] <jdh> lemme look.
[18:25:36] <jdh> 5420,5421
[18:25:42] <joe9> ok, thanks.
[18:25:53] <joe9> sorry for the bother, jdh. where did you look, btw?
[18:26:30] <jdh> you could probably G92 also (and then subtract) but G92 confuses me
[18:27:17] <jdh> http://linuxcnc.org/docs/2.5/html/gcode/overview.html#sub:numbered-parameters
[18:28:37] <Connor> Blue to purple chips with Carbide turning tool is correct turning speed ? (Lathe)
[18:28:58] <joe9> jdh, thanks. that is exactly what I needed.
[18:30:40] -!- tjb1 has quit [Quit: tjb1]
[18:30:52] -!- Nick001-Shop [[email protected]] has joined #linuxcnc
[18:33:50] -!- automata__ has quit [Ping timeout: 246 seconds]
[18:37:04] -!- bedah has quit [Quit: Ex-Chat]
[18:40:43] -!- Thetawaves [[email protected]] has joined #linuxcnc
[18:40:53] <Loetmichel> re @ home
[18:44:05] -!- JT-Shop has quit [Read error: Connection reset by peer]
[18:44:30] <skunkworks> joe9, I don't understand - doesn't g30 just work for you (if you define g30 as the probe locatioin) it doesn't affect your current coordinat system...
[18:45:56] <Loetmichel> *hrmpf*... i think i get old. just 12 hrs @ work and already back pain... (muscles prostesting the lifting/standing up) :-(
[18:49:05] -!- gmagno has quit [Ping timeout: 252 seconds]
[18:57:36] -!- factor has quit [Read error: Connection reset by peer]
[18:57:50] <mcenter__> Connor, Blue to purple chips with carbide generally optimal. But, not a requirement
[18:58:48] <mcenter__> As long as you are making well-formed chips and nothing sounds or feels amiss.
[19:03:49] <joe9> skunkworks: i did not figure out how G30.1 works. so, was looking for something easier.
[19:03:58] <joe9> skunkworks: let me check up on G30.1 again.
[19:04:28] <skunkworks> joe9, do you have home switches? (is your machine homed to a know position every time you use it?)
[19:04:33] <Connor> mcenter__: That's what I thought. It looked like it was cutting good at the speed.
[19:04:39] <joe9> skunkworks: yes, I have home switches.
[19:04:47] <joe9> yes, it is always the same position.
[19:04:55] <Connor> First time I used carbide inserts.
[19:05:02] <Connor> Normally use HSS cutters.
[19:05:10] -!- broofa has quit [Quit: Leaving...]
[19:05:20] <skunkworks> then you can go to your tool lenght swith and do a g30.1 and then from that point on - G30 will go to your switch.
[19:05:41] <joe9> with gcode, it is annoying that you get the message about the outermost subroutine, but, not the exact line in the inner most subroutine that has the error.
[19:07:19] -!- gmagno [[email protected]] has joined #linuxcnc
[19:08:57] <joe9> Is there some setting for the error code to drill into the inner subroutine with the error.
[19:08:57] <joe9> skunkworks: ok, thanks. will check it out.
[19:11:43] <joe9> http://codepad.org/nzjNxTCu is my gcode with a tool probe switch, it also sets the G55 touchoff
[19:11:52] <joe9> any kind comments to make it better, please?
[19:15:08] -!- factor [factor!~factor@r74-195-185-157.msk1cmtc01.mskgok.ok.dh.suddenlink.net] has joined #linuxcnc
[19:16:38] <jdh> have you tried probing the PCB?
[19:23:32] -!- Patang has quit [Ping timeout: 246 seconds]
[19:24:05] <jdh> #<_x> - Return absolute machine X coordinate. Same as #5420.
[19:27:22] <joe9> jdh, not sure what you mean. will get into that in a minute.
[19:27:48] <joe9> What would the touchoff value: at -5.44, I can make a small scratch on the dowel or the touchoff piece,
[19:28:09] <joe9> and at -5.439, it passes without the scratch.
[19:28:28] <joe9> should my touchoff be at -5.439 or -5.44?
[19:28:44] <joe9> any thoughts, please? How do you normally set it?
[19:29:38] <jdh> that would be entirely up to you.
[19:29:58] -!- Patang [[email protected]] has joined #linuxcnc
[19:30:23] <jdh> but, I would make zero not touching and -0.00000001 touching
[19:30:47] <joe9> jdh: wow, that is a very high precision.
[19:31:14] <joe9> I think my machine is precise upto only 0.0003 or something like that. it is a taig mill.
[19:31:43] <joe9> so, I think I should stick with -5.439.
[19:33:07] <jdh> it was an arbitrary point. zero should not be touching, anything less than zero should be.
[19:34:03] <joe9> jdh, ok, thanks.
[19:37:20] <jdh> http://www.cnczone.com/forums/pcb_milling/82628-cheap_simple_height-probing-9.html#post811490
[19:41:09] <joe9> jdh, thanks.
[19:43:32] -!- Cylly2 [[email protected]] has joined #linuxcnc
[19:43:50] -!- Loetmichel has quit [Disconnected by services]
[19:43:52] Cylly2 is now known as Loetmichel
[19:45:06] -!- erasmo [[email protected]] has joined #linuxcnc
[19:53:41] -!- gallenat0r has quit [Quit: This computer has gone to sleep]
[20:07:17] -!- sumpfralle1 [[email protected]] has joined #linuxcnc
[20:07:17] -!- psha has quit [Read error: Connection reset by peer]
[20:07:25] -!- psha [[email protected]] has joined #linuxcnc
[20:10:33] -!- sumpfralle has quit [Ping timeout: 245 seconds]
[20:14:13] <joe9> is this a correct way of setting default values to a subroutine?
http://codepad.org/MQU6v7M9
[20:14:16] <joe9> in gcode
[20:14:58] -!- tjb1 [[email protected]] has joined #linuxcnc
[20:15:22] -!- tjb1 has quit [Client Quit]
[20:16:49] <joe9> this is with axis gui
[20:18:55] <jdh> I would think you would need an IF block for each one to determine if you needed to use the default.
[20:19:24] -!- broofa has quit [Ping timeout: 240 seconds]
[20:19:27] <jdh> but, I wouldn't allow defaults.
[20:24:01] <joe9> jdh: i was thinking of an if statement, but, was not sure how to check for an "undefined" value.
[20:24:22] <joe9> i am not sure if undefined values are 0?
[20:24:24] <jdh> check for 0 maybe?
[20:24:33] <jdh> but, I wouldn't allow defaults.
[20:25:05] -!- erasmo has quit [Ping timeout: 256 seconds]
[20:26:39] <joe9> if 0, then error -- ok, good idea.
[20:27:05] -!- Brandonian has quit [Quit: Brandonian]
[20:28:20] -!- JT-Shop [[email protected]] has joined #linuxcnc
[20:34:28] <JT-Shop> anyone know how to make a model rocket igniter
[20:34:44] <JT-Shop> that I might use to touch off my cannon...
[20:34:57] <jdh> nichrome wire and a little powder?
[20:35:31] <Jymmm> JT-Shop: Yws, but it's disposable
[20:35:33] <Jymmm> yes
[20:35:44] <JT-Shop> it takes kinda high current for nichrome
[20:35:50] <Jymmm> JT-Shop: nah
[20:36:12] <Jymmm> JT-Shop: Recall that I have 100K feet in various gauges =)
[20:37:00] <JT-Shop> I guess if you had some small enough, all I have is foam cutting wire I think I still have it
[20:37:47] <jdh> http://makeprojects.com/Project/Model-Rocket-Igniters/386/1#.UCLN06AWo0E
[20:38:21] -!- erasmo [[email protected]] has joined #linuxcnc
[20:38:24] -!- psha has quit [Quit: Lost terminal]
[20:38:38] <jdh> geez... I haven't seen one of those in 30+ years. Still the same though.
[20:39:48] <JT-Shop> one of the first ones that popped up with a google search for me :)
[20:39:52] <Jymmm> JT-Shop: Heh, that Make project is wussy igniters =)
[20:40:50] <DJ9DJ> gn8
[20:41:39] -!- DJ9DJ has quit [Quit: bye]
[20:43:49] -!- erasmo has quit [Ping timeout: 244 seconds]
[20:45:34] <JT-Shop> hmm, I have some 0.010" copper wire
[20:47:41] <Jymmm> JT-Shop: If you have 30ga SS wire, that could work
[20:48:02] <Jymmm> JT-Shop: I have Nichrome from 18 to 40ga =)
[20:49:45] <Jymmm> JT-Shop: Also...
http://www.pyrouniverse.com/fusemaking/igniters.htm
[20:50:03] <Jymmm> JT-Shop: I have "other" pyro resources too
[20:50:24] <JT-Shop> 0.010" is 30 gauge so it should work too
[20:51:19] <Jymmm> is ss or nichrome?
[20:51:21] <Jymmm> in
[20:51:26] <JT-Shop> copper
[20:51:34] <Jymmm> cnt use copper
[20:51:38] <Jymmm> SS or NiChrome
[20:51:39] <JT-Shop> why
[20:51:50] <Jymmm> resistance
[20:52:02] <JT-Shop> I just watched a video of a kid doing it with copper wire
[20:52:15] <JT-Shop> and 4.5v worth of a cells
[20:52:20] <Jymmm> ok, fine, you could use steel wool too
[20:52:55] <Jymmm> but copper cant handle 2200F
[20:53:52] <Jymmm> you want a fuse or a RELIABLE igniter is my point.
[20:54:25] <JT-Shop> I assume it will get blown to hell and back when the cannon goes off
[20:54:38] <Jymmm> and I have a way to make them without having to was visco ether
[20:54:43] <Jymmm> waste
[20:56:09] <Jymmm> JT-Shop: a little better
http://www.pyrouniverse.com/show/fusing/joeematch.htm
[20:56:14] -!- erasmo [[email protected]] has joined #linuxcnc
[20:57:13] <Jymmm> JT-Shop: Kayton tape is heat resistant fwiw
[20:57:33] <Jymmm> JT-Shop: Never try to solder nichrome, crimp only
[20:57:49] -!- FinboySlick has quit [Quit: Leaving.]
[20:58:23] -!- djcoin has quit [Client Quit]
[20:59:04] <Loetmichel> Jymmm: it is, but only up to ~250°c
[20:59:33] <Jymmm> Loetmichel: lol
[21:00:25] <Loetmichel> ?
[21:00:55] <Jymmm> 250C != 1200C
[21:01:00] <Jymmm> not even close =)
[21:02:02] -!- Keknom [[email protected]] has joined #linuxcnc
[21:03:11] <Loetmichel> kayton
[21:03:20] <Loetmichel> sorry i had read kapton
[21:03:24] -!- tjb1 [[email protected]] has joined #linuxcnc
[21:03:53] <Jymmm> I said Kapton...
http://en.wikipedia.org/wiki/Kapton
[21:04:10] <Jymmm> but I was tlaking about 1200C for NiChrome
[21:04:24] <Jymmm> (max working temp)
[21:04:50] <Loetmichel> Jymmm: kapton TAPE should not be used above 250-300°C
[21:05:04] <Jymmm> it says 400C
[21:05:07] <Loetmichel> because it will harden/decomposite
[21:05:24] <Jymmm> and for what jt's doing, it's fine, just adding some water proofing
[21:05:38] <Loetmichel> in long term
[21:05:59] <Jymmm> he's going to blow the shit up (literally), it's perfectly fine.
[21:06:51] <Loetmichel> ok, if you are talking "short term" then you are right.
[21:07:54] <Thetawaves> thanks for the info Loetmichel
[21:08:05] <Thetawaves> but hopefully my mosfets aren't getting up to 250C
[21:08:11] <Loetmichel> hrhr
[21:08:52] -!- tjb1 has quit [Quit: tjb1]
[21:08:57] <Loetmichel> i cant tell for mosfets, but i had 2n3055 desoldering themsef more than once
[21:09:13] <Loetmichel> and working perfectly after resoldering ;-)
[21:09:18] <Thetawaves> haha
[21:10:16] <Loetmichel> ... maybe i made the heatinks a TAD to small ;-)
[21:10:19] <Loetmichel> heatsinks
[21:26:45] -!- syyl has quit [Quit: Leaving]
[21:29:22] -!- erasmo has quit [Remote host closed the connection]
[21:32:05] -!- tjb1 [[email protected]] has joined #linuxcnc
[21:34:49] <Tom_itx> JT-Shop go to the hobby store and get some model rocket igniters
[21:35:06] <JT-Shop> we don't have a hobby store
[21:35:19] <Tom_itx> mmm
[21:36:28] -!- tjb1 has quit [Client Quit]
[21:37:23] <Tom_itx> http://www.amazon.com/Estes-2301-Rocket-Igniters/dp/B000TF4DUO/ref=sr_1_1?ie=UTF8&qid=1344461752&sr=8-1&keywords=estes+rocket+igniters
[21:37:31] <Tom_itx> amazon sells everything
[21:38:11] <JT-Shop> I keep forgetting to look at amazon
[21:38:16] <Jymmm> JT-Shop: u r a pita
[21:38:29] -!- skunkworks has quit [Read error: Connection reset by peer]
[21:38:31] <JT-Shop> whats your point?
[21:38:54] <Jymmm> JT-Shop: go get one of those $4 soldering pencils. they have about 2-5 feet of nichrome wire in them
[21:39:00] <Tom_itx> note that it's listed under "Toys"
[21:39:59] <Jymmm> JT-Shop: without looking it up 30ga nicrhome is around 3.2 ohms per foot
[21:40:24] <Tom_itx> Jymmm i gave you a bunch of numbers on that a while back
[21:40:29] <Jymmm> maybe 0.3 OPF something liek that. just measure it
[21:40:38] <Jymmm> Tom_itx: on what?
[21:40:44] <Tom_itx> nicrome wire
[21:40:50] <Tom_itx> h
[21:41:17] <Jymmm> Tom_itx: I doubt it, I've been using nichrome for years and had a metallurist does soem formulas for me and the foundry.
[21:41:29] <Jymmm> s/and/at/
[21:41:43] <Jymmm> Tom_itx: Oh, you meant he strip. I'm tlaking wire
[21:41:56] <Tom_itx> he has wire as well i believe
[21:42:05] <Jymmm> yeah, copper.
[21:42:11] <Tom_itx> no nichrome
[21:42:16] <Jymmm> no, JT-Shop
[21:42:32] <Jymmm> Tom_itx: JT-Shop wants to make electric matches
[21:42:42] <Tom_itx> i know
[21:43:09] <Jymmm> Tom_itx: so what does me wanting strip for heating have to do with JT-Shop wanting wire for matches?
[21:43:12] <Tom_itx> you need a batch of igniter to dip it in don't you?
[21:43:35] <Jymmm> yo make it eextra special yes. but not required
[21:43:51] <Jymmm> JT-Shop: can use fuse
[21:44:11] -!- chillly has quit [Quit: Leaving]
[21:44:36] <Jymmm> I do have a better way of making them, but JT-Shop dont wanna hear it (or at least nto from me =)
[21:47:26] -!- FinboySlick [[email protected]] has joined #linuxcnc
[21:48:52] <Jymmm> good use for CAT3 if you have some =)
[21:54:03] -!- mhaberler has quit [Ping timeout: 256 seconds]
[21:56:36] -!- i_tarzan has quit [Read error: Operation timed out]
[22:03:13] -!- anick has quit [Quit: Page closed]
[22:05:10] <Tom_itx> http://makeprojects.com/Project/Make-your-own-model-rocket-igniters/386/1#.UCLibqAcaBM
[22:12:28] -!- tjb1 [[email protected]] has joined #linuxcnc
[22:12:29] -!- tjb1 has quit [Client Quit]
[22:27:10] -!- FinboySlick has quit [Remote host closed the connection]
[22:27:48] -!- Nick001 has quit [Read error: Connection reset by peer]
[22:32:07] GeorgeH-Away is now known as GeorgeH
[22:32:12] -!- GeorgeH has quit [Quit: Leaving]
[22:32:32] -!- GeorgeH [[email protected]] has joined #linuxcnc
[22:33:41] -!- em__ has quit [Quit: Page closed]
[22:47:38] -!- Guthur has quit [Remote host closed the connection]
[23:17:14] -!- FinboySlick [[email protected]] has joined #linuxcnc
[23:21:57] -!- rob_h has quit [Ping timeout: 248 seconds]
[23:24:33] -!- servos4ever has quit [Quit: ChatZilla 0.9.85 [SeaMonkey 2.0.11/20101206162726]]
[23:27:57] -!- skunkworks__ [skunkworks__!~chatzilla@str-bb-cable-south-3-102.dsl.airstreamcomm.net] has joined #linuxcnc
[23:29:14] <jthornton> I think it is easier to just buy some estes rocket igniters
[23:29:25] <jdh> most likely
[23:30:03] <jthornton> as I don't have any small gauge nichrome wire only big stuff for foam cutting
[23:30:32] <jthornton> and Jymmm won't send me any 30ga nichrome to play with
[23:30:41] <jdh> what an ass.
[23:30:59] <jdh> surely they have hobby stores in .mo.us or wtf.us
[23:31:49] <jthornton> they might have a hobby store in Cape which is a 75 minute drive... one way
[23:32:14] <jdh> geez
[23:32:31] <jthornton> well you can't have everything
[23:33:11] <jthornton> I don't know what to tell this guy...
http://linuxcnc.org/index.php/english/component/kunena/?func=view&catid=38&id=22980#22982
[23:34:56] <jdh> I haven't tried 2.5.1. Is there anything intersting?
[23:35:04] <jthornton> how do you revert back to 2.5.0?
[23:35:38] <jthornton> just
http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Released_2.5.X
[23:35:50] <r00t4rd3d> invert?
[23:36:37] <r00t4rd3d> you remove 251 and reinstall 250
[23:36:40] <skunkworks__> odd.
[23:36:48] <jthornton> yes odd
[23:36:56] <r00t4rd3d> could he not just invert the axis thats backwards?
[23:37:23] <jthornton> he did that now his limits are backwards
[23:37:23] <r00t4rd3d> if i was him i would create a new ini with 251
[23:37:39] <r00t4rd3d> you can invert the limits too cant you?>
[23:37:51] <jthornton> sure
[23:37:51] <r00t4rd3d> everything has a invert check box i think
[23:38:11] <jthornton> that would just invert the limit switch itself
[23:38:33] <jthornton> I think he is saying that his table limits are backwards now
[23:38:48] <jdh> non shared limits?
[23:39:23] <jthornton> no, his + and - distance for limits
[23:40:18] <jdh> oh. and his motors were backwards?
[23:40:45] <jthornton> he didn't mention anything about motors
[23:41:17] <jdh> the x and y axis changed the direction
[23:41:30] <jdh> guess I really have no idea what he meant by that.
[23:41:55] <jthornton> me neither
[23:42:01] <skunkworks__> he maybe should have inverted the direction pin instead of the scale....
[23:42:19] <jdh> whit the stepconf wizard I changed the sign of the x and y axis direction.
[23:42:34] <r00t4rd3d> i hope you did that by mistake
[23:44:54] <r00t4rd3d> i would tell him to back up his old ini and generate a new one with 251
[23:45:02] <r00t4rd3d> see what that does
[23:45:12] <jdh> mine wasn't very generatable
[23:48:41] <jthornton> I see help has arrived :)
[23:50:08] -!- geo01005 [[email protected]] has joined #linuxcnc
[23:53:07] <r00t4rd3d> it has to be in his ini file
[23:53:51] <r00t4rd3d> A new post has been made to a topic to which you have subscribed on the LinuxCNC Support Forum Forum
[23:53:59] <r00t4rd3d> i could kill a bitch
[23:54:39] <r00t4rd3d> automatic subscribed with email alerts?
[23:54:48] <jdh> change your settings
[23:55:12] <r00t4rd3d> that is a setting that should not be default was my point
[23:56:50] -!- gmagno has quit [Ping timeout: 252 seconds]
[23:56:54] <r00t4rd3d> where the hell is that setting, not in my profile
[23:57:07] <jdh> heh
[23:57:40] <r00t4rd3d> ffs
[23:57:54] -!- Nick001-Shop has quit [Quit: ChatZilla 0.9.88.2 [Firefox 14.0.1/20120713134347]]
[23:58:08] <r00t4rd3d> http://linuxcnc.org/index.php/english/my-profile-usermenu-17/userprofile/r00t4rd3d
[23:58:17] -!- Tom_L [Tom_L!~Tl@unaffiliated/toml/x-013812] has joined #linuxcnc
[23:58:26] <r00t4rd3d> jthornton, ^^ can u delete that please.
