#linuxcnc | Logs for 2012-11-11

Back
[00:04:20] -!- logger[mah] has quit [Remote host closed the connection]
[00:04:27] -!- logger[mah] [logger[mah][email protected]] has joined #linuxcnc
[00:04:43] -!- erasmo has quit [Remote host closed the connection]
[00:12:49] -!- the_wench has quit [Ping timeout: 246 seconds]
[00:12:54] -!- archivist has quit [Ping timeout: 240 seconds]
[00:18:03] -!- rob__H has quit [Ping timeout: 260 seconds]
[00:25:42] -!- archivist [[email protected]] has joined #linuxcnc
[00:30:08] -!- Tugge has quit [Read error: Operation timed out]
[00:30:38] -!- tjb1 [[email protected]] has joined #linuxcnc
[00:31:16] <tjb1> Im trying to tie all homing sensors to one input but it tells me that is already in use
[00:33:04] <andypugh> tjb1: Use the signal name, not the pin name
[00:35:20] -!- Valen has quit [Quit: Leaving.]
[00:37:40] <tjb1> andypugh: So i would use net-both-home-x
[00:37:55] <tjb1> Well that was the name made for x
[00:37:56] <andypugh> Yes
[00:40:57] <tjb1> I copied the x to the z and its just hitting home and saying it is on limit, it doesnt back off and search again
[00:41:08] <tjb1> What should i look at
[00:41:18] -!- asdfasd [[email protected]] has joined #linuxcnc
[00:41:21] <andypugh> Set HOME_IGNORE_LIMITS in the INI file
[00:41:34] <tjb1> It is set to yes
[00:42:25] <andypugh> Bah! I can't remember the other one, this may take seveal seconds.
[00:43:22] <tjb1> The x will search quick, back off and go slow...the z just hits and says joint on limit
[00:43:29] <andypugh> 2.10.1 HOME_IS_SHARED http://www.linuxcnc.org/docs/html/config/ini_config.html#_axis_lt_num_gt_section_a_id_sub_axis_section_a
[00:44:35] <tjb1> No switches are set though
[00:45:37] <tjb1> Oh its tripping x switch when homing z?
[00:46:05] <andypugh> Yes.
[00:46:20] <tjb1> So that should be 0
[00:47:28] <andypugh> Z hitting the home switch looks like X hitting a limit. And despite what the manual says, I think you want "1" or "TRUE" (and in all AXES)
[00:48:32] <tjb1> Neither works
[00:52:23] <tjb1> I found this "To use only one input for all homing and limits you will have to block the limits of the axis not homing with axis that is homing in HAL."
[00:52:38] <tjb1> Doesnt say how though
[00:57:56] <tjb1> I found it, JT-Shop shows it here http://linuxcnc.org/lucid/emc2/emc2/index.php/french/forum/38-general-linuxcnc-questions/9633-combine-all-home-and-limit-switches?start=18
[00:59:55] <tjb1> JT-Shop: Helllp
[01:02:22] <andypugh> I am sure that it is meant to be a built-in possibility
[01:02:47] <andypugh> Do your axes move off the switches as the last stage of homing?
[01:05:27] -!- tjb1 has quit [Ping timeout: 245 seconds]
[01:07:37] -!- tjb1 [[email protected]] has joined #linuxcnc
[01:08:22] <ReadError> tjb1
[01:08:26] <ReadError> got some prints done finally
[01:08:27] <tjb1> yes?
[01:08:45] <ReadError> https://dl.dropbox.com/u/25091878/Photo%20Nov%2010%2C%207%2015%2012%20PM.jpg
[01:08:55] <tjb1> Im banging my head with these electronics…I spent 3 hours to find out my 12v wall wart wasnt enough for my fans and homing switches :(
[01:09:16] <tjb1> Thats nice ReadError
[01:09:26] <tjb1> What are you printing
[01:10:01] <r00t4rd3d> a new house
[01:10:39] <r00t4rd3d> tjb1, http://i.imgur.com/c3QxD.jpg
[01:10:41] <ReadError> still calibrating and stuff
[01:10:53] <tjb1> You made that r00t?
[01:10:54] <mutilator> pff i print out spaceships
[01:11:12] <r00t4rd3d> yeah
[01:11:14] <tjb1> JT-Shop: jthornton are you here?
[01:12:54] <r00t4rd3d> ive since sanded and cleaned it
[01:13:52] <tjb1> Has a cool font
[01:14:07] <tjb1> Be careful doing copyrighted items...
[01:14:42] <r00t4rd3d> i have no morals.
[01:14:57] <mutilator> lol
[01:15:05] <andypugh> Neither do lawyers
[01:15:06] <tjb1> Well when they rape you in court
[01:16:01] <r00t4rd3d> you can use stuff like that for personal use
[01:16:48] <r00t4rd3d> its when you sell stuff like that panties start knotting up.
[01:16:51] <t12> the only acceptable non-rights thing you're allowed to print
[01:16:54] <t12> is richard m stallmans face
[01:17:06] <tjb1> why I gave up vinyl cutting
[01:17:11] <tjb1> everything is against the law to make
[01:17:27] <tjb1> Well everything someone wants…can you cut me the chevy bowtie? no...
[01:18:01] <tjb1> ReadError: Is the perimiter to get the nozzle cleaned and purged and to make sure its extruding good?
[01:19:07] <tjb1> What is this "13 Mai 2011 04:26" is that supposed to be May?
[01:20:02] <andypugh> C'est francaise. Ou sont les mots en question?
[01:22:03] -!- ve7it has quit [Remote host closed the connection]
[01:22:17] <r00t4rd3d> french is for fries.
[01:22:23] <tjb1> andypugh: Thats on http://linuxcnc.org/lucid/emc2/emc2/index.php/french/forum/38-general-linuxcnc-questions/9633-combine-all-home-and-limit-switches?start=18
[01:22:29] <tjb1> Nothing else is in french
[01:22:47] <r00t4rd3d> you are in the french section
[01:22:48] <tjb1> Wait...yes
[01:22:53] <tjb1> Damn google :/
[01:22:59] <r00t4rd3d> look at your link
[01:23:41] <tjb1> Im gonna go before I look any more retarded
[01:23:52] <r00t4rd3d> is that possible?
[01:23:57] <r00t4rd3d> :)
[01:24:05] <tjb1> :|
[01:24:08] -!- tjb1 has quit [Quit: tjb1]
[01:24:27] <r00t4rd3d> I buy the one Android phone you cant update/root/rom :(
[01:35:35] -!- tjb1 [[email protected]] has joined #linuxcnc
[01:35:57] <tjb1> To use xor2 do I need to place "loadrt xor2" at the beginning of hal file?
[01:37:54] <andypugh> Yes
[01:38:30] -!- tjb1 has quit [Client Quit]
[01:39:01] -!- asdfasd has quit [Ping timeout: 256 seconds]
[01:53:44] -!- tjb1 [[email protected]] has joined #linuxcnc
[01:53:52] <tjb1> ok andypugh I have another question…probably really simple
[01:54:06] <andypugh> 42
[01:54:08] <tjb1> To use xor2 in a second instance I need "xor2.1 correct
[01:54:35] <tjb1> xor2.1.in0, in1, etc...
[01:54:59] <andypugh> Yes, and that needs count=2 in the loadrt line
[01:55:11] <tjb1> Thats what I was looking for, thanks!
[01:55:14] -!- tjb1 has quit [Client Quit]
[01:55:27] -!- Keknom [[email protected]] has joined #linuxcnc
[01:57:15] <andypugh> Or, if you want, you can give them all names: loadrt xor2 names=obama,romney,palin than net something palin.in0
[01:57:17] <Tecan> http://youtu.be/3FpjcOWwiI4 << tesla coil fun
[01:57:21] -!- tjb1 [[email protected]] has joined #linuxcnc
[01:57:31] <tjb1> loadrt xor2 [count=2] gives me empty variable name
[01:58:02] <andypugh> don't put the [] in
[01:58:38] <tjb1> just "loard rt xor2 count=2
[01:58:40] <tjb1> "
[01:59:16] <andypugh> Tecan: The guys should have been orange and green
[02:00:02] -!- tjb1 has quit [Client Quit]
[02:05:05] -!- tjb1 [[email protected]] has joined #linuxcnc
[02:05:18] <tjb1> Ok andypugh, last time I promise...
[02:05:35] <tjb1> This works for homing both but now limits dont work - http://pastebin.com/pt7jpcK6 the xors are at the end
[02:06:47] -!- factor has quit [Read error: Connection reset by peer]
[02:09:10] -!- factor [factor!~factor@r74-195-216-98.msk1cmtc02.mskgok.ok.dh.suddenlink.net] has joined #linuxcnc
[02:09:20] <andypugh> Is xor what you want? That seems like it will set the everything pin the instant homing starts, then set it to zero when the switch trips.
[02:10:24] <andypugh> I _think_ you want the homes to be straight through, and the limits to be AND NOT homing
[02:10:38] <tjb1> I was using what JT posted in that thread
[02:11:15] <andypugh> Yes, and as I said earlier, I am not sure he is right. I thought that all-shared was trivially configurable.
[02:11:37] <andypugh> Did you try all 4 combinations
[02:11:51] <tjb1> 4 combinations?
[02:12:02] <tjb1> Of the all-shared?
[02:12:28] <tjb1> Right now im only working with X and Z but I will have Y soon also
[02:14:12] <andypugh> There are 4 combinations of ignore-limits and home-is-shared
[02:16:57] <tjb1> Like ignore limits no, home shared 1 -- ignore limits yes, home shared 1 -- ignore limits yes, home shared 0 -- ignore limits yes, home shared 1?
[02:17:13] <andypugh> Yes
[02:17:41] <andypugh> home-is-shared is per-axis by the way.
[02:18:01] <tjb1> Well if it doesnt ignore the limts its going to trip all the time when homing
[02:18:09] -!- factor has quit [Read error: Connection reset by peer]
[02:19:20] <andypugh> I would expect so, but at least one LinuxCNC dev is barely competent (though I haven't touched homing)
[02:32:23] <Tom_itx> one switch for both functions?
[02:33:07] <Tom_itx> i haven't been following...
[02:35:26] <andypugh> Yes, one pin handling home and limit for every axis.
[02:36:50] <andypugh> I wanted http://www.ebay.co.uk/itm/BT30-spindle-speed-multiplier-/181012927719?nma=true&si=PQpYFLIAvsBr4Fk6DPdQbZ4pUy4%3D&orig_cvip=true&rt=nc&_trksid=p2047675.l2557
[02:36:54] -!- factor [[email protected]] has joined #linuxcnc
[02:36:59] <andypugh> But not badly enough.
[02:37:42] <Tom_itx> but then Lcnc wouldn't know what switch tripped
[02:37:46] <Tom_itx> just that one did
[02:38:26] <Tom_itx> andypugh, a gearhead?
[02:38:38] <andypugh> I guess so
[02:38:48] <Tom_itx> why did you want that?
[02:38:54] <Tom_itx> i've never seen one
[02:40:05] <andypugh> My BT30 mill is geared for a top speed of 1000rpm, and a lowest speed of 47rpm. I have a VFD. Low gear, minimum frequency is more like a clock than a spindle (and has enormous torque)
[02:40:17] <Tom_itx> oh
[02:40:23] <Tom_itx> yeah i bet it has torque
[02:40:29] <Tom_itx> no way to regear it?
[02:40:42] <andypugh> Yes, and I intend to.
[02:41:02] <Tom_itx> may have to change bearings
[02:41:12] <Tom_itx> depending on how high you go
[02:41:21] <andypugh> The machine had two motor options and two head-gearing options from the factory. I seem to have the special slow one.
[02:41:43] <Tom_itx> for steel work probably
[02:42:29] <andypugh> But the bearings are the same (hand-engraved and signed in France, bizarrely) for all versions, so 2800rpm is fine
[02:42:47] <Tom_itx> yeah 2800 isn't bad
[02:43:15] <andypugh> I am looking out for an _enormous_ face mill to make the lower gears worthwhile
[02:43:19] <Tom_itx> i made a high speed pulley for my sherline as well
[02:43:27] <Tom_itx> apparently it's bearings are the same
[02:43:36] <Tom_itx> like 6"?
[02:43:51] <andypugh> No, bigger than that. 47rpm?
[02:43:55] <Tom_itx> hmm
[02:44:06] <Tom_itx> with 30 taper??
[02:44:16] <andypugh> There are dogs
[02:44:23] <Tom_itx> still
[02:44:35] <Tom_itx> side loads come into play with the tapers
[02:45:20] <andypugh> You are probably right. I am actually more likely to make a fly-cutter holder for one of my lathe tools.
[02:45:27] <Tom_itx> you may be limited what you can find with 30 taper too
[02:46:12] <Tom_itx> our big machines were 50 taper and you didn't really need to worry much about it
[02:47:28] <andypugh> I hadn't seen these until last week. They look quite nice. (They do bigger for more cash) http://www.ebay.co.uk/itm/Fly-Cutter-for-Boring-Mill-Bridgeport-CNC-Verticall-Mill-Horizontal-Mill-Fadal-/320842397830?pt=LH_DefaultDomain_0&hash=item4ab3b27886
[02:50:50] <Tom_itx> yeah
[02:51:07] <andypugh> Video: http://youtu.be/FMNkPCtkM80
[02:52:32] <Tom_itx> the only issue would be balance and vibrations but the rpm may not be high enough to worry
[02:52:52] <Tom_itx> especially on the larger diameter settings
[02:53:53] <Tom_itx> larger diameter the slower you have to go so i'm not sure how much you really gain
[02:54:40] <andypugh> Skimming the whole part in one pass, regardless of if it is slower than 2 passes looks a lot nicer
[02:54:54] <Tom_itx> yeah you don't get the blend marks
[02:55:21] * Tom_itx goes back to his movie
[02:56:44] -!- ybon has quit [Quit: WeeChat 0.3.8]
[03:06:30] -!- yuvipanda has quit [Quit: yuvipanda]
[03:07:13] -!- andypugh has quit [Quit: andypugh]
[03:16:26] -!- Tecan has quit [Quit: live long and phosphor]
[03:28:38] <roh> hm.. what are typical speeds for stepper driven ballscrews on 'small' mills?
[03:35:38] <roh> i just wonder if i should invest time in tuning it even more
[03:39:25] -!- br87 [[email protected]] has joined #linuxcnc
[03:39:34] <br87> hey, anyone awake?
[03:39:44] <br87> why does channel EMC point me to this channel?
[03:44:18] <roh> because linuxcnc was named emc2 for about a decade
[03:44:39] -!- mmcloud [[email protected]] has joined #linuxcnc
[03:44:50] -!- mmcloud [[email protected]] has parted #linuxcnc
[04:02:30] -!- FinboySlick [[email protected]] has joined #linuxcnc
[04:53:13] -!- pjm__ has quit [Read error: Connection reset by peer]
[04:53:33] -!- pjm__ [[email protected]] has joined #linuxcnc
[05:04:24] -!- hdokes_ has quit [Ping timeout: 276 seconds]
[05:34:58] -!- br87 has quit []
[05:36:15] -!- erictheise has quit [Quit: erictheise]
[05:46:25] -!- cmorley [[email protected]] has joined #linuxcnc
[06:02:20] -!- Fox_Muldr has quit [Ping timeout: 260 seconds]
[06:04:14] -!- Fox_Muldr [[email protected]] has joined #linuxcnc
[06:12:14] -!- zzolo has quit [Quit: zzolo]
[06:15:03] <tjb1> Tom_itx: You here?
[06:40:22] -!- factor has quit [Read error: Connection reset by peer]
[06:46:58] <tjb1> Anyone doing a build…do NOT use solid wire...
[06:47:00] <tjb1> I could shoot myself
[06:56:03] -!- Shadowtec [[email protected]] has joined #linuxcnc
[06:58:11] <Shadowtec> o/
[07:01:22] <tjb1> o/?
[07:11:12] -!- tjb1 has quit [Quit: tjb1]
[07:14:49] -!- the_wench [[email protected]] has joined #linuxcnc
[07:20:33] -!- Shadowtec [[email protected]] has parted #linuxcnc
[07:22:11] -!- FinboySlick has quit [Quit: Leaving.]
[07:30:08] -!- mhaberler [[email protected]] has joined #linuxcnc
[07:49:37] -!- theos has quit [Ping timeout: 245 seconds]
[07:52:41] -!- yuvipanda has quit [Quit: yuvipanda]
[07:55:39] -!- factor [[email protected]] has joined #linuxcnc
[07:55:41] -!- DJ9DJ [DJ9DJ!~Deejay@unaffiliated/dj9dj] has joined #linuxcnc
[07:59:39] <DJ9DJ> moin
[08:01:02] -!- vladimirek [[email protected]] has joined #linuxcnc
[08:06:28] -!- factor has quit [Ping timeout: 268 seconds]
[08:06:35] -!- theos [theos!~theos@unaffiliated/theos] has joined #linuxcnc
[08:13:51] -!- Keknom has quit [Quit: Leaving.]
[08:14:45] -!- factor [factor!~factor@r74-195-184-59.msk1cmtc01.mskgok.ok.dh.suddenlink.net] has joined #linuxcnc
[08:18:37] -!- the_wench has quit [Ping timeout: 246 seconds]
[08:18:54] -!- archivist has quit [Ping timeout: 240 seconds]
[08:20:43] -!- archivist [[email protected]] has joined #linuxcnc
[08:20:49] -!- the_wench [[email protected]] has joined #linuxcnc
[09:00:02] -!- syyl_ [[email protected]] has joined #linuxcnc
[09:03:36] -!- syyl has quit [Ping timeout: 276 seconds]
[09:13:20] -!- racycle has quit [Quit: racycle]
[09:13:51] -!- KimK_laptop [[email protected]] has joined #linuxcnc
[09:23:05] -!- rob_h [[email protected]] has joined #linuxcnc
[09:23:53] -!- Cylly [[email protected]] has joined #linuxcnc
[09:26:06] -!- Loetmichel has quit [Ping timeout: 240 seconds]
[09:26:11] -!- KimK_laptop_ [[email protected]] has joined #linuxcnc
[09:26:34] -!- KimK_laptop has quit [Quit: Leaving]
[09:27:47] -!- KimK_laptop [[email protected]] has joined #linuxcnc
[09:28:04] -!- KimK_laptop_ has quit [Client Quit]
[10:32:54] -!- asdfasd [[email protected]] has joined #linuxcnc
[10:41:37] -!- mhaberler has quit [Quit: mhaberler]
[10:49:59] -!- Cylly has quit []
[10:50:06] -!- Loetmichel [[email protected]] has joined #linuxcnc
[11:17:18] -!- mhaberler [[email protected]] has joined #linuxcnc
[11:40:02] -!- gambakufu has quit [Ping timeout: 260 seconds]
[11:49:48] -!- gambakufu [[email protected]] has joined #linuxcnc
[11:59:38] -!- sumpfralle [[email protected]] has joined #linuxcnc
[12:20:51] -!- bedah [[email protected]] has joined #linuxcnc
[12:39:49] -!- yuvipanda has quit [Quit: yuvipanda]
[13:53:41] -!- oyildirim [[email protected]] has joined #linuxcnc
[13:58:02] -!- mhaberler has quit [Quit: mhaberler]
[14:24:31] -!- andypugh [andypugh!~andy2@cpc2-basl1-0-0-cust639.basl.cable.virginmedia.com] has joined #linuxcnc
[14:48:52] -!- mattions has quit [Ping timeout: 246 seconds]
[14:53:21] -!- skunkworks has quit [Ping timeout: 252 seconds]
[15:04:42] -!- pcw_home has quit [Quit: ChatZilla 0.9.89 [Firefox 16.0.1/20121010231231]]
[15:06:05] <JT-Shop> yep
[15:07:02] -!- pcw_home [[email protected]] has joined #linuxcnc
[15:19:05] -!- leehambley has quit [Quit: leehambley]
[15:21:50] -!- grummund has quit [Ping timeout: 268 seconds]
[15:22:02] -!- mhaberler [[email protected]] has joined #linuxcnc
[15:23:28] -!- grummund [grummund!~user@unaffiliated/grummund] has joined #linuxcnc
[15:28:53] <JT-Shop> pcw_home: drives off http://imagebin.org/235449
[15:29:16] <JT-Shop> drives on http://imagebin.org/235451
[15:30:10] <JT-Shop> scope ground on PC case, probe on 7i77 ground TB2 pin 8
[15:32:01] <pcw_home> what is the scope vertical scale? (volts/div)
[15:33:58] <pcw_home> also a sanity check is to connect both scope gnd and probe to PC case
[15:34:07] <archivist> and is it a x10 probe
[15:34:49] -!- paideia [[email protected]] has joined #linuxcnc
[15:34:51] <JT-Shop> 1 v/div and yes a 10x probe
[15:35:31] <JT-Shop> both gnd and probe connected to the pc is flat line
[15:36:01] <JT-Shop> adding a ground wire from the pc to the backplane of the el cabinet reduced the trace by 1/2
[15:37:05] <JT-Shop> all 120v items are plugged into the same plug strip
[15:37:13] <JT-Shop> the drives are noisy for sure
[15:37:37] <JT-Shop> the only other power is the 240v single phase to the VFD
[15:37:56] <pcw_home> Yeah the a pretty large about of noise across a shielded cable
[15:38:29] <pcw_home> s/the/thats/
[15:38:42] <andypugh> Tektronix scopes know when they have a 10x Tekronix probe attaged (that extra ring round the BNC socket)
[15:38:59] <pcw_home> with tek probes
[15:39:21] <archivist> if they have a tek lead with the right bnc on it
[15:40:04] <archivist> but I see from the onscreen that the peak detect is set rather slow possibly
[15:40:46] <pcw_home> do you somehow have the cable shield grounded to the el cabinet?
[15:42:28] <pcw_home> (at the 7I77 end)
[15:42:40] -!- maximilian_h [[email protected]] has joined #linuxcnc
[15:45:04] -!- mhaberler has quit [Quit: mhaberler]
[15:47:03] <JT-Shop> the shield is connected to the GND pin on TB5
[15:47:05] <andypugh> Should the 7i77 be on insulated or conductive mounting posts?
[15:47:28] <JT-Shop> the other end is neatly covered with heat shrink tubing
[15:49:39] <JT-Shop> one with peakdet faster http://imagebin.org/235453
[15:51:24] <pcw_home> The mounting holes are isolated so either is fine
[15:52:11] <pcw_home> heat shrink?
[15:54:11] <pcw_home> the shield (DB25 shell) should connect to both the 5I25 bracket/PC case and 7I77 GND
[15:55:54] <JT-Shop> the drive input cable is covered with heat shrink on the drive end so only the + and - wires are exposed
[15:56:57] <pcw_home> OK, I was asking if the DB25 shell is grounded at the 7I77 end somehow
[15:59:10] <JT-Shop> I added studs to the 7i77 so the DB25 screws have something to thread into
[16:00:06] <pcw_home> You can also probe the DB25 shield at the 7I77 end, and the PC (5I25) end to see if the noise is truly across the cable shield/twisted pair GNDs or there a open at either end (bracket to case at 5I25 end?)
[16:00:08] <pcw_home>
[16:01:04] <pcw_home> But it does sound like bonding the PC case to GND may be the solution (unless you want to try some ferrite)
[16:01:20] <pcw_home> bbl
[16:01:26] <JT-Shop> ok
[16:02:20] <pcw_home> if thats not enough next step is bond 7I77 to GND (strap under DB25 studs)
[16:03:20] <andypugh> <several steps later> Immerse all components in a grounded tank of mercury...
[16:03:35] <pcw_home> If thats not enough a common mode choke on 7I77 encoder leads may be needed
[16:04:06] <pcw_home> (giant ferrite bead, one per encoder)
[16:04:17] <JT-Shop> one thing I noticed is the drive power 0vdc is not grounded http://imagebin.org/235455
[16:04:57] <pcw_home> Thats probably for the best
[16:05:29] <JT-Shop> ok, didn't know
[16:07:03] <pcw_home> If all else fails as andy about the sserial errors a occasional one should be maskable
[16:07:12] <pcw_home> ask andy
[16:07:41] <pcw_home> really bbl
[16:07:49] -!- mhaberler [[email protected]] has joined #linuxcnc
[16:07:55] <JT-Shop> ok
[16:08:15] <JT-Shop> from the pc ground to the 7i77 db25 shell is pretty clean
[16:09:18] -!- oyildirim has quit [Read error: Connection reset by peer]
[16:09:39] -!- oyildirim [[email protected]] has joined #linuxcnc
[16:22:10] -!- skunkworks [[email protected]] has joined #linuxcnc
[16:24:06] -!- the_wench has quit [Ping timeout: 264 seconds]
[16:24:34] -!- archivist has quit [Ping timeout: 240 seconds]
[16:37:34] -!- archivist [[email protected]] has joined #linuxcnc
[16:38:09] -!- the_wench [[email protected]] has joined #linuxcnc
[16:42:10] <andypugh> Love this profile picture: http://www.facebook.com/neil.ronketti
[16:50:05] -!- maximilian_h [[email protected]] has parted #linuxcnc
[17:00:13] <archivist> is he hoping to get responsible work :)
[17:01:56] -!- rob__H [[email protected]] has joined #linuxcnc
[17:02:24] -!- skunkworks_ [[email protected]] has joined #linuxcnc
[17:05:30] -!- rob_h has quit [Ping timeout: 264 seconds]
[17:05:38] -!- tjb1 [[email protected]] has joined #linuxcnc
[17:07:45] -!- ve7it [[email protected]] has joined #linuxcnc
[17:13:28] -!- zzolo has quit [Quit: zzolo]
[17:15:00] -!- tjb1 has quit [Ping timeout: 252 seconds]
[17:15:12] -!- tjb1 [[email protected]] has joined #linuxcnc
[17:15:40] -!- alpha1125 [[email protected]] has joined #linuxcnc
[17:22:07] <archivist> so can I trust this idiots measuring fleabay 181017344864
[17:23:00] <archivist> his answer for the bore is "around 3/8 or 10mm"
[17:24:03] <Loetmichel> hrhr
[17:24:08] <Loetmichel> so what?
[17:24:27] <Loetmichel> buy them and ream the diameter to something fitting ;-)
[17:24:55] <archivist> 10mm is too loose
[17:25:05] -!- psha [[email protected]] has joined #linuxcnc
[17:33:28] <archivist> I dont have a deckel or no4 morse 251179373631
[17:48:27] -!- IchGuckLive [[email protected]] has joined #linuxcnc
[17:48:31] <IchGuckLive> hi All
[17:52:10] <andypugh> archivist: Easily (though not cheaply fixed) http://www.ebay.co.uk/itm/221151065803
[17:52:19] <tjb1> Got my plasma x axis up to 1500 ipm last night :)
[17:52:40] <archivist> andypugh, I saw that the other day :)
[17:52:48] <IchGuckLive> tjb1: Whow stepper or servo
[17:52:54] <tjb1> Stepper
[17:53:11] -!- FinboySlick [[email protected]] has joined #linuxcnc
[17:53:31] <IchGuckLive> hope you did not lost stepps
[17:54:07] <tjb1> I wasnt running it at 1500, just seeing what it could do
[17:54:14] -!- yuvipanda has quit [Quit: yuvipanda]
[17:54:32] <IchGuckLive> controller is mesa
[17:54:57] <tjb1> gecko g540
[17:55:24] <IchGuckLive> nice what latency you got on the pc
[17:55:51] <tjb1> I think the base period was set at about 20k
[17:56:15] <IchGuckLive> ok and the scale is
[17:56:46] <tjb1> I would have to look it up
[17:57:32] <tjb1> base period is 16k
[17:57:41] <tjb1> x scale is 1737
[17:59:55] <IchGuckLive> can you get your timing to here -> http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Stepper_Drive_Timing
[18:00:18] <tjb1> You want the timing?
[18:00:55] <IchGuckLive> no the Gecko 540 is not in this list
[18:01:12] <IchGuckLive> i think stepconf has it
[18:01:13] <tjb1> The gecko g540 is 4 gecko drives
[18:01:33] -!- JesusAlos [[email protected]] has joined #linuxcnc
[18:02:01] <tjb1> http://www.geckodrive.com/geckodrive-step-motor-drives/g540.html
[18:02:43] <archivist> andypugh, another toy for the garage if everything else was moved out 120995422866
[18:03:57] <andypugh> That's lovely. But postage would be a killer.
[18:04:14] -!- FinboySlick has quit [Quit: Leaving.]
[18:04:32] <archivist> postman would struggle at that weight
[18:05:19] <archivist> must stop dreaming of toys and make something
[18:05:45] <IchGuckLive> i se at the calculation with 18k Base and stepgen.steplen/stepspace/dirsetup/dirhold set to 1 a max of 27.5ksteps/sec
[18:07:42] <IchGuckLive> that gives me a 15.8inch per sec = 950inch pewr min save rate
[18:08:01] -!- JT-Shop has quit [Read error: Connection reset by peer]
[18:08:24] -!- JT-Shop [[email protected]] has joined #linuxcnc
[18:09:29] <Tom_itx> IchGuckLive, what's your servo period?
[18:09:30] <tjb1> I have 16k base
[18:10:01] <IchGuckLive> servo period on steppper not requirerd
[18:10:06] <Tom_itx> iirc you don't use base period with mesa cards
[18:10:17] <Tom_itx> i was told different
[18:10:52] <SWPadnos> servo thread is always necessary, base thread may or may not be needed
[18:10:53] <IchGuckLive> i only go max 800mm/min on my education mashines
[18:11:31] <Tom_itx> check my ini and see if it looks ok then...
[18:11:34] <Tom_itx> http://tom-itx.dyndns.org:81/~webpage/cnc/configs/sherline/sherline.ini
[18:11:46] <Tom_itx> servo period seems kinda high to me
[18:11:48] <Tom_itx> i dunno
[18:12:00] <IchGuckLive> always 1mio on steppers
[18:13:04] <Tom_itx> mine works good but if i can get better performance...
[18:13:05] <SWPadnos> that's a 1ms servo period, which is normal
[18:13:48] <Tom_itx> no need for a base period?
[18:14:07] <Tom_itx> 7i43 7i47
[18:14:21] <SWPadnos> I don't know at this point. There used to be a time when the base period still had to be specified, but you just wouldn't put any functions in it
[18:14:38] <Jymmm> Hi SWPadnos
[18:14:41] <Tom_itx> iirc PCW said i don't need it
[18:14:45] <SWPadnos> and it can be 1/2 or 1/10 the servo period (or the same, I think), it doesn't have to be really fast
[18:14:45] <Loetmichel> IchGuckLive: 800mm/min IS VERY slow. even my small 200*110mm mill has 1500mm G0... and that is slow as well
[18:14:49] <SWPadnos> hi Jymmm
[18:15:05] -!- servos4ever [[email protected]] has joined #linuxcnc
[18:15:07] <Loetmichel> (have to upgrade my PSU to 40V, than F3000 will be possible)
[18:15:14] <Jymmm> SWPadnos: Still alive I see =)
[18:15:28] <SWPadnos> yep, at least I have that going for me :)
[18:15:33] <IchGuckLive> Loetmichel: its enove to ram the tool in the plate
[18:15:44] <IchGuckLive> Students love to break the tool
[18:15:50] <IchGuckLive> savty first
[18:16:26] <Jymmm> SWPadnos: Good to hear, as the alternative would be purchasing 6ft of real estate, and not a good thing in this economy... Wouldn't want to be forclosed upon
[18:16:39] <SWPadnos> Jymmm, got a question for you. I have an old HD image from an 8G drive, and I have some new computers with 32G drives instead. I had made a script to prep new drives using partimage, parted, grub-install, etc, but it doesn't seem to work on the 32G drives
[18:16:53] <SWPadnos> yeah, they charge a lot for depth
[18:17:17] <Loetmichel> IchGuckLive: its even enough to weld the TC bit to the vise ;-) (BTDT ;-)
[18:18:00] <IchGuckLive> the tool is not flying very far Loetmichel at that speed
[18:18:30] <andypugh> You don't need a base period, but I think Motion always creates one.
[18:18:34] * Loetmichel hat moved sideways with the tool shaft into the vice
[18:18:39] <Jymmm> SWPadnos: not sure why you need ALL that; are you restoting an image or doing a fresh install on the 32g drives?
[18:18:50] <SWPadnos> the failure mode is either (a) it hangs or eventually reboots without printing anything, (b) prints GRUB repeatedly, or (c) says "no system disk or disk error, insert disk to continue"
[18:19:00] <SWPadnos> restoring an image
[18:19:07] <Loetmichel> steppers stopped, but pressure was enough to weld the mill bit @ 24krpm to the vice
[18:19:14] <Jymmm> SWPadnos: then why parted?
[18:19:37] <Loetmichel> in a split second
[18:19:49] <SWPadnos> the drives are IDE, so there's a weirdness there since all my current systems are SATA (so the drive names are different)
[18:20:02] <Loetmichel> it has gone from red to white hot, then "esc", spindle stoppend: bit welded to the vice
[18:20:03] <SWPadnos> parted to make the partition the size of the disk
[18:20:03] <Loetmichel> ;-)
[18:20:12] <SWPadnos> if I dd the 8G image to the 32G drive, it works
[18:20:17] <SWPadnos> so I have that as a fallback
[18:20:44] <Jymmm> SWPadnos: these are all signle partition images?
[18:20:45] <SWPadnos> I think I can dd the whole image, resize the partition, then resize2fs, which is what I'm in the process of trying now
[18:20:47] <SWPadnos> yes
[18:20:56] <SWPadnos> one image, many computers
[18:21:00] <Jymmm> SWPadnos: Ok, this is what I've always done....
[18:21:47] <Jymmm> SWPadnos: create two IMG files... 1) using partimage, 2) Using dd to backup the MBR.
[18:22:18] <Jymmm> SWPadnos: Restorre the img file to the new drive using partimage
[18:22:30] <Jymmm> SWPadnos: Restore the MBR using dd
[18:22:58] <SWPadnos> hmm. maybe I had the order backwards
[18:23:15] <SWPadnos> do you have any need for grub-install?
[18:23:22] <Jymmm> SWPadnos: Then use parted/gparted to resize the partition to utilize the extra space on the new hdd (if you want)
[18:23:30] <Jymmm> SWPadnos: nope, never.
[18:24:33] <SWPadnos> hmmm, ok. I'll take a look at the order I did things. I think I made the partitions, used grub-install, restored the partition (but maybe not the whole disk) with parted, then resized the partition, then resize2fs ...
[18:24:35] <SWPadnos> thanks
[18:24:36] <Jymmm> SWPadnos: Backup MBR: dd if=/dev/hdx of=/path/to/image count=1 bs=512
[18:24:53] <Jymmm> SWPadnos: I usually name the file *.mbr
[18:25:14] <Jymmm> SWPadnos: and it's only 512 BYTES =)
[18:25:15] <SWPadnos> sure, got a few of those :)
[18:25:20] <SWPadnos> yeah
[18:25:32] <SWPadnos> vbindiff is your friend, by the way
[18:25:35] <SWPadnos> and ghex
[18:25:51] <Jymmm> SWPadnos: in partimage, I do NOT use compression, take too long.
[18:26:20] <SWPadnos> it seems OK on the restore, though the backup does take a while
[18:26:31] <Jymmm> SWPadnos: shouldn't
[18:26:42] <SWPadnos> so the partimage backup is the partition only, not the whole disk?
[18:26:56] -!- yuvipanda has quit [Ping timeout: 252 seconds]
[18:27:06] <Jymmm> SWPadnos: partimage == partition image, not disk image =)
[18:27:17] <SWPadnos> I think there's an option to do the whole disk
[18:27:32] <SWPadnos> but you're right, and that may be why I have parted in the prep script :)
[18:27:42] <SWPadnos> I wrote it 2 years ago, and haven't thought about it since then :)
[18:28:11] <Jymmm> SWPadnos: I would not recommend multiple partitions if you dont have to. It's just a PITA
[18:28:51] <SWPadnos> right, it's an SSD which gets mounted RO in the actual system, so there's no big issue with keeping boot separate or anything
[18:29:29] <Jymmm> SWPadnos: Also, dont create an 10GB img file from a (lets say) 40GB hdd and attempt to restore it to a 30GB hdd, even though the img file is only 10gb, it doens't like it.
[18:29:46] <SWPadnos> yep, you can go one way but not the other
[18:29:56] <SWPadnos> you'd be missing some important inodes
[18:30:07] <Jymmm> well, emty ones
[18:30:18] <Jymmm> partimage doens't backup empty space
[18:30:24] <Jymmm> dd does
[18:31:25] <SWPadnos> sure, but the superblocks are distributed around the disk, and some might fall off the end if you restore to a smaller disk
[18:32:52] <Jymmm> SWPadnos: I use http://sysresccd.org/ It has all the tools and even connectivity
[18:33:17] <SWPadnos> oh, I have a laptop (the craptop ;) ) with all the image files and the USB->PATA adapter
[18:33:47] <Jymmm> ok
[18:34:36] <Jymmm> SWPadnos: Usualy I have dead systems with no bootable, so LiveUSB works for me. Also in case soemthing is fubar
[18:34:58] <SWPadnos> yep
[18:35:16] <SWPadnos> these are new systems though, I'm just trying to prep them in 5 minutes each instead of an hour
[18:35:20] -!- mattions has quit [Ping timeout: 246 seconds]
[18:35:23] <Jymmm> SWPadnos: It can read most any file system too
[18:35:29] <SWPadnos> that hasn't worked out too well so far
[18:36:17] <Jymmm> SWPadnos: grab a couple usb sticks and create that link
[18:36:56] <SWPadnos> yeah, an 8 or 16 GB USB stick could prep the disks in the machines, which could be nice
[18:37:04] <IchGuckLive> ARE you folks using the live system also on the D525
[18:37:13] <SWPadnos> or 4G if I use the compressed image
[18:37:32] <Jymmm> SWPadnos: dont compresss unless you want to be there forever
[18:37:48] <SWPadnos> restores take about 2-3 minutes on my laptop
[18:37:55] <SWPadnos> so the compression doesn't seem to be an issue
[18:38:20] <SWPadnos> that's for ~3GB of data over USB, on an 8G partition
[18:38:22] <Jymmm> but you're not going to be booting from your laptop =)
[18:38:47] <SWPadnos> err - the images are compressed, but it uncompresses for the restore, no?
[18:39:19] <SWPadnos> or are you talking about sysresccd?
[18:39:19] <Jymmm> SWPadnos: Yes, but youre restoring on an atom board, not some obscene quad core craptop
[18:39:40] <SWPadnos> no, I do the restore on the laptop, then put the drive in the machine
[18:39:49] <Jymmm> SWPadnos: no need
[18:39:50] <SWPadnos> which is a dual-core core2 anyway
[18:40:04] <SWPadnos> sure, with a USB stick I could do the restore on the machine itself
[18:40:14] <Jymmm> SWPadnos: Get a few usb sticks and restore to all of the boxes at the same time
[18:40:23] <SWPadnos> but that doesn't help much, since I need to open the machine to install a 5i22 anyway
[18:40:35] <SWPadnos> if only I had that many outlets and monitors ;)
[18:40:49] <SWPadnos> or do net restore from the laptop
[18:41:02] <Jymmm> SWPadnos: if you set it up right, you dont have to. It also has remote headless iface
[18:41:10] <Jymmm> network
[18:41:11] <SWPadnos> ^^
[18:41:34] <Jymmm> no , more terminal iface
[18:42:17] <SWPadnos> ssh to computer running from USB stick, run partimage from there, pulling image from laptop
[18:42:19] <SWPadnos> :)
[18:42:40] <Jymmm> SWPadnos: Ignore your laptop completely
[18:42:48] <Jymmm> take it out of the picture
[18:42:53] <SWPadnos> sure, that's one way to do it
[18:43:18] <SWPadnos> but then I have to create scripts that run automatically from the USB stick, or I need a monitor/keyboard to start the process
[18:43:36] <SWPadnos> once I've created the USB stick with the image
[18:43:51] <Jymmm> No, sysresccd creates an sshd
[18:44:13] <SWPadnos> but that's not really a help here, since there are hardware and serial number logging tasks I have to do, which take about the same amount of time as the disk prep
[18:44:42] <SWPadnos> oh, you may be missing one thing - the original image is on the laptop, so I can't *completely* ignore ir
[18:44:45] <SWPadnos> it
[18:44:53] <Jymmm> we werent taking about your serial number and other hw installations
[18:45:04] <SWPadnos> no, we weren't
[18:45:16] <Jymmm> you create a 2nd partitiion on the usb stick for the img file
[18:45:28] <Jymmm> which sysresccd reads from
[18:45:55] <SWPadnos> sure
[18:46:03] <Jymmm> You can even have multiple img files/versions
[18:46:14] <SWPadnos> yep, space permitting
[18:46:52] <SWPadnos> I could do it with a hard drive in a USB enclosure as well (I don't have any USB sticks of the right size that I can blow away at the moment)
[18:47:33] <Jymmm> SWPadnos: http://www.sysresccd.org/Sysresccd-manual-en_How_to_personalize_SystemRescueCd
[18:49:17] <Jymmm> SWPadnos: whatever works for you
[18:49:29] <SWPadnos> yep. thanks for the pointers
[18:49:50] <Jymmm> SWPadnos: Though if you are installing HW I'm not sure ow you are going to test it withut a lcd/kybd
[18:50:31] <SWPadnos> yep. that's why fully automating isn't a priority at the moment
[18:50:59] <SWPadnos> just getting it so that the disk prep is automatic and results in a bootable hard drive is enough for me
[18:51:05] -!- yuvipanda has quit [Quit: yuvipanda]
[18:51:10] <SWPadnos> I only have to prep 8 computers, so it's not a huge issue
[18:52:03] <Jymmm> not even worth writting a script for
[18:52:38] <SWPadnos> no, that's worthwhile so I can do the hardware stuff while the hard drive is out of the machine and attached to the laptop :)
[18:53:24] <Jymmm> not really, just do the first, swap hdd, up arrow twice ENTER, lather rinse repeat
[18:54:36] -!- factor has quit [Read error: Operation timed out]
[18:55:01] <SWPadnos> hmmm. in your description of what you do, you say to restore the image using partimage before you restore the MBR using dd. Did you skip creating the partition (with parted or whatever) on purpose?
[18:55:22] <Jymmm> yep
[18:55:32] <SWPadnos> the last step in your list is to optionally resize the partitions using parted
[18:55:50] <Jymmm> I used gpated, same diff
[18:55:51] <SWPadnos> so it's OK to restore a partimage backup to a drive, then replace the MBR ??
[18:56:00] <SWPadnos> sure, script vs. GUI
[18:56:28] <SWPadnos> seems like you'd be a sector off or partimage wouldn't know where to put the data or something
[18:56:33] <Jymmm> partimage funkily does MBR restore. It has the option, but doesn't always work.
[18:57:03] <Jymmm> dd backup/resotre of MBR ALWAYS worked.
[18:57:16] <SWPadnos> ok, and it has the MBR information in the partimage backup?
[18:57:36] <SWPadnos> (or at least enough information to fake it sometimes)
[18:57:39] <Jymmm> no, a seperate file, remember *.MBR
[18:58:01] <Jymmm> two files needed to restore
[18:58:12] <Jymmm> .img and .mbr
[18:58:35] <SWPadnos> ah, ok. I thought the mbr backup was from dd
[18:58:43] <SWPadnos> so you have two, one from partimage and one from dd
[18:58:47] <Jymmm> it's created/restored using dd
[18:58:53] <Jymmm> correct
[18:59:34] <Jymmm> backup mbr: dd if=/dev/hdx of=/path/to/image count=1 bs=512
[18:59:47] <SWPadnos> yeah, that one I have and use
[18:59:47] <Jymmm> restore mbr: dd if=/path/to/image of=/dev/hdx
[19:00:40] <Jymmm> It'll backup/restore the mbr so fast that you will think it didn't do anything.
[19:01:17] <Jymmm> it'll take you longer to type the command than it does to do the comand =)
[19:01:47] <SWPadnos> heh
[19:02:28] <SWPadnos> hmmm. it looks like this version of partimage automatically saves the MBR. do you know how to tell if an image file contains the MBR?
[19:02:40] <Jymmm> SWPadnos: What did I say?
[19:02:56] <SWPadnos> you said several things
[19:03:04] <Jymmm> SWPadnos: I said that partimage has the option to backup/restore the mbr, but it doens't always work.
[19:03:12] <SWPadnos> exactly
[19:03:22] <Jymmm> so DONT TRY IT
[19:03:32] <Jymmm> dd works 100% of the time
[19:03:40] <SWPadnos> except in this case
[19:03:45] <Jymmm> so DONT TRY IT
[19:04:04] <SWPadnos> but the real problem might be that I do the partimage restore after the dd MBR restore
[19:04:09] <SWPadnos> so I'll fix that
[19:04:25] <Jymmm> partimage, then dd mbr
[19:05:19] <Jymmm> partimage write funky shit to the mbr
[19:05:44] <Jymmm> thus the dd AFTER partimage restore
[19:05:48] <SWPadnos> sure
[19:06:09] <SWPadnos> presumably you only use the drive name in the partimage command, since there's no partition table yet
[19:06:18] <Jymmm> to clear out the crap that partimage writes to the mbr that prevents it from booting.
[19:07:07] <Jymmm> SWPadnos: KISS
[19:07:22] <Jymmm> it's not that complicated
[19:07:25] <SWPadnos> yes, I understand the idea, it's the details I'm working on now ;)
[19:07:27] <Jymmm> dont make it so
[19:07:40] <SWPadnos> partimage restore /dev/sdb blah blah
[19:07:53] <SWPadnos> dd if=mymbrfile of=/dev/sdb bs count ...
[19:08:00] <SWPadnos> parted resize (optional)
[19:08:07] <Jymmm> SWPadnos: if you are using a usb to sata adapter, the device is going to change dynamically
[19:08:08] <SWPadnos> resize2fs (optional)
[19:08:15] <SWPadnos> understood
[19:08:28] <Jymmm> just do it manually
[19:08:34] <SWPadnos> but it's always /dev/sdb for me, since I'm only doing one drive at a time
[19:09:00] <Jymmm> doesn't matter, it cna change on the fly
[19:09:49] <Jymmm> just swapping to the 3rd it can become /dev/sde
[19:10:59] <SWPadnos> err - I'm smart enough to not plug in other USB drives when this process is running ;)
[19:11:28] <Jymmm> not while running, after it's done and you move on to the next one.
[19:11:53] <andypugh> But are you dumb enough not to get totally bored and stop conetrating on iteration 6 of 8?
[19:12:12] <SWPadnos> I never concentrate
[19:12:23] <SWPadnos> so yes, I am dumb enough for that
[19:13:07] <Jymmm> and when dealing with dd you dont want the device to change to /dev/sda on ya, ot you really will have a craptop =)
[19:13:28] <Jymmm> or a DOAtop =)
[19:13:55] <andypugh> A notebook (if you stick paper to the screen)
[19:13:58] <SWPadnos> well, the laptop has SATA drives, so the script specifically checks to see if that's the target, and refuses to run if so
[19:14:03] <Jymmm> SWPadnos: I'm just telling you the SAFE way to do it.
[19:14:28] <andypugh> Jymmm: I think you should try to be more patronising.
[19:14:55] <Jymmm> andypugh: thats your job.
[19:15:11] <andypugh> No, I defer to your superior skill :-)
[19:17:01] <Jymmm> SWPadnos: scripts fubar, Do you ant to be 1000 miles form nowhere with a dead laptop? realize I do this with stacks of systems sitting on a bench and liveBoot them from USB hdd's, away from my "real" systems
[19:17:49] <SWPadnos> I'm at home, so it's OK
[19:17:57] <Jymmm> SWPadnos: It's nothing to be doing six concurrently.
[19:17:58] <SWPadnos> plus this is the older laptop, not my new one
[19:18:09] <SWPadnos> well, I have that hardware thing, remember ...
[19:18:32] <Jymmm> to install a card that take 30s?
[19:21:09] <Jymmm> SWPadnos: and since when does mobo have SN's?
[19:21:31] <Jymmm> SWPadnos: you getting fancy on me now?
[19:21:48] <SWPadnos> I'm recording the SN of the computer in a spreadsheet, and it takes a little while to install the card since this is a small industrial computer
[19:22:59] <Jymmm> ah
[19:24:10] <Jymmm> SWPadnos: you could just create a pxe server that does all that for you =)
[19:24:17] -!- IchGuckLive has quit [Quit: ChatZilla 0.9.87 [Firefox 16.0.2/20121025205401]]
[19:24:39] <Jymmm> SWPadnos: and no robotic arm to install the card?! tsk tsk tsk
[19:25:16] <mrsun> replacing cv-joint ... now thats a messy job =)
[19:25:21] <SWPadnos> heh
[19:26:36] <mrsun> atleast the car doesnt crackle when i turn anymore =)
[19:26:43] <mrsun> so hopefully i did something right
[19:27:08] <Jymmm> Oh hey.... have you guys seen any "clips" that can SECURELY attach to a (solid) wire?
[19:27:40] -!- factor [factor!~factor@r74-195-184-59.msk1cmtc01.mskgok.ok.dh.suddenlink.net] has joined #linuxcnc
[19:27:41] <Jymmm> this isn't perm
[19:27:54] <Jymmm> likea durable test/tap clip
[19:28:33] <Jymmm> all I can find are the spring loaded hook clips
[19:30:27] <SWPadnos> if an alligator clip isn't enough, then a screw terminal of some sort is probably your best bet
[19:30:28] -!- JT-Shop has quit [Read error: Connection reset by peer]
[19:30:29] -!- JT-Shop-2 [[email protected]] has joined #linuxcnc
[19:30:42] <Jymmm> I need this hook, but in a smaller overall version http://salestores.com/stores/images/images_747/TL741.jpg
[19:31:21] <Jymmm> SWPadnos: this is tapping into the middle of a coil
[19:32:42] <Jymmm> a stubby version of that could work
[19:33:18] <SWPadnos> yeah. if that type of clip isn't good enough, then you would need something pretty expensive to get much more reliable
[19:33:34] <Jymmm> such as?
[19:33:38] <SWPadnos> or at least I don't know of any inexpensive alternatives that I would expect to work any better
[19:34:11] <SWPadnos> oh, I don't know of any specific once, I'm just thinking that you'd need a couple of springy leaf contacts, so if there were any vibration at least one would stay in contact
[19:34:19] <SWPadnos> s/once/ones/
[19:34:29] <mrsun> Jymmm, for measuring or branching the wire off or what is it supposed to be used for ?
[19:34:30] <andypugh> Jymmm: http://www.rapidonline.com/Cables-Connectors/SMD-Test-clips-63859
[19:35:39] <andypugh> 1.2mm probe diameter, good for wires up to 0.6mm
[19:36:09] <andypugh> Designed for 0.8mm pitch leads
[19:37:38] <mrsun> http://www.biltema.se/ProductImages/44/large/44-035_l.jpg permanent
[19:38:17] <Jymmm> No, not perm =)
[19:39:08] <andypugh> Jymmm: Even smaller: http://www.rapidonline.com/Cables-Connectors/Challenger-clip-67848
[19:39:36] <Jymmm> andypugh: but it's spring loaded, and I dont think strong enough
[19:42:26] <andypugh> http://uk.mouser.com/ProductDetail/Pomona-Electronics/4521-2/?qs=sGAEpiMZZMt6TxecXUIS9hsaGMVHajqkFOPdedTlAuM%3d
[19:43:46] <Jymmm> https://www.youtube.com/watch?v=EzaLdfcPOyI
[19:44:05] <Loetmichel> the pomoma have the tendency to melt if more than 1 or 2 amps are drawn over it
[19:44:13] -!- kwallace [[email protected]] has joined #linuxcnc
[19:44:21] <Jymmm> Loetmichel: 100W RF =)
[19:46:33] <Jymmm> Eh, I guess I'll use one of these bad boys http://sigma.octopart.com/10250271/image/Mueller-BU-27C.jpg
[19:46:44] <Jymmm> that should handle 75MPH =)
[19:47:36] -!- skunkworks_ has quit [Ping timeout: 256 seconds]
[19:48:28] <Jymmm> Hmmm, I think I might have foud em http://www.eham.net/data/classifieds/images/373685.jpg
[19:50:00] <kwallace> Has anyone tried rigid tapping with pecking? I've only done tapping in one cycle on my HNC, but it just came to mind that I usually peck when I tap by hand.
[19:50:17] <alex_joni> different taps for hand tapping and for machine tapping
[19:50:31] <alex_joni> if you use a hand tap, then it might make sense to peck
[19:51:16] <Loetmichel> i use machine taps also for hadn tapping
[19:51:38] <Loetmichel> and skip the pecking
[19:52:07] <kwallace> There is _no_ situation where peck tapping would be needed with CNC?
[19:53:00] <Loetmichel> kwallace: wiht the right taps: no
[19:53:18] <andypugh> kwallace: https://www.youtube.com/watch?v=jAcFeVlftrw
[19:54:50] <Tom_itx> kwallace, probably not
[19:54:55] <Tom_itx> spiral point taps for cnc
[19:55:08] <Tom_itx> pushes the shavings ahead of the tap
[19:55:29] <Tom_itx> unless you got a blind hole
[19:55:35] <Loetmichel> http://www.cyrom.org/palbum/main.php?g2_itemId=3031 <- like the right one
[19:55:48] <Loetmichel> i use them for machine AND hand tapping
[19:56:06] <Loetmichel> and they are for blind holes
[19:56:18] <Tom_itx> spiral flute pull the chips out though right?
[19:56:24] <Tom_itx> spiral point push them
[19:56:25] <Loetmichel> yes
[19:57:08] -!- yuvipanda has quit [Ping timeout: 252 seconds]
[19:58:04] -!- skunkworks has quit [Read error: Connection reset by peer]
[19:59:45] -!- factor has quit [Read error: Connection reset by peer]
[20:01:25] <kwallace> andypugh: Thanks for the video link. I suppose the uncoordinated bits between the passes gets fixed because the index is used. I would suspect changing Z between passes would mess things up. Just a guess.
[20:04:26] <andypugh> Yes, you only change start Z if you _want_ a multi-start thread
[20:13:02] JT-Shop-2 is now known as JT-Shop
[20:13:07] <Tom_itx> that would require a special tap anyway
[20:13:19] <Tom_itx> unless you're single pointing it
[20:15:32] -!- psha has quit [Quit: Lost terminal]
[20:17:49] -!- factor [factor!~factor@r74-195-184-59.msk1cmtc01.mskgok.ok.dh.suddenlink.net] has joined #linuxcnc
[20:18:36] <andypugh> No, you can always take out extra metal.
[20:18:44] <andypugh> I have done it enough times :-)
[20:19:50] <Tom_itx> heh
[20:20:14] <Tom_itx> i suppose if the pitch is coars enough you could double it and get a 2 start
[20:20:19] <Tom_itx> coarse*
[20:20:35] <Tom_itx> i've not heard of that done though
[20:21:04] -!- FinboySlick [[email protected]] has joined #linuxcnc
[20:22:43] -!- phantoneD [[email protected]] has joined #linuxcnc
[20:23:55] -!- JesusAlos has quit [Quit: ChatZilla 0.9.89 [Firefox 16.0.2/20121024073032]]
[20:25:44] -!- phantoxeD has quit [Ping timeout: 252 seconds]
[20:27:00] <Tom_itx> i'd like to try rigid tapping on my sherline but i'm not set up for it
[20:28:03] <ReadError> hey guys
[20:28:13] <ReadError> is it worth getting powerfeed on a lathe?
[20:28:25] <ReadError> i might need to do some threading before i convert it to cnc
[20:34:20] -!- Flipp [[email protected]] has joined #linuxcnc
[20:35:51] <Flipp> hey all, got a basic SolidWorks question and was told someone here might be able to help: is there a way to get SW to identify Z as "up" instead of Y?
[20:36:46] <JT-Shop> yea, let me try and remember... something about rotating the coordinate system
[20:37:18] <Flipp> thanks! ya, I was imagining something like that, but my google searches were just coming up on how to change the views, not the coordinate system itself.
[20:39:24] <JT-Shop> Insert > Reference Geometry > Coordinate System
[20:41:24] <JT-Shop> X Axis Right Plane and Z Axis top plane
[20:45:35] <Flipp> thanks, I'll see if I can mess with it and get it working
[20:48:11] -!- motioncontrol [motioncontrol!~io@host15-72-dynamic.6-87-r.retail.telecomitalia.it] has joined #linuxcnc
[20:50:54] -!- motioncontrol has quit [Client Quit]
[20:51:02] <tjb1> JT-Shop: Can you take a look at this if you have time? http://linuxcnc.org/index.php/english/forum/49-basic-configuration/25832-multiple-axes-homing-1-input
[20:55:09] <Flipp> JT-Shop: Thanks a bunch. The only piece I was missing was shift-clicking on the z-axis to rotate the view 90 deg. works perfectly now!
[20:55:46] -!- tjb1 has quit [Quit: tjb1]
[20:55:48] -!- JT-Shop-2 [[email protected]] has joined #linuxcnc
[20:56:25] -!- jthornton has quit [Read error: Connection reset by peer]
[20:56:30] -!- JT-Shop has quit [Read error: Connection reset by peer]
[20:57:15] -!- jthornton [[email protected]] has joined #linuxcnc
[20:59:55] <JT-Shop-2> I looked at it but could not understand what you were asking...
[21:00:02] JT-Shop-2 is now known as JT-Shop
[21:00:24] -!- vladimirek has quit [Remote host closed the connection]
[21:01:31] -!- jthornton has quit [Read error: Connection reset by peer]
[21:01:32] -!- JT-Shop has quit [Read error: Connection reset by peer]
[21:02:58] -!- jthornton [[email protected]] has joined #linuxcnc
[21:02:58] -!- JT-Shop [[email protected]] has joined #linuxcnc
[21:05:41] -!- bedah has quit [Quit: gn8]
[21:08:09] <JT-Shop> satellite internet sucks when it rains
[21:08:43] <Tom_itx> you must be getting what we got last night
[21:09:04] <JT-Shop> cold front I think
[21:09:06] <Tom_itx> it went from 70f to 35 today too
[21:09:20] <JT-Shop> yea we get that tonight I think
[21:10:52] <JT-Shop> hmm better roll up the hoses tomorrow, Monday night low of 30F
[21:11:22] <p0staL> halo o'clock?
[21:11:30] <Tom_itx> i should blow out the sprinklers but it's been soooo dry
[21:18:10] -!- Tecan [[email protected]] has joined #linuxcnc
[21:18:10] -!- Tecan has quit [Changing host]
[21:18:10] -!- Tecan [Tecan!~fasdf@unaffiliated/unit41] has joined #linuxcnc
[21:18:52] -!- Aero-Tec has quit [Remote host closed the connection]
[21:23:33] <JT-Shop> I should be doing something but I don't know what
[21:23:50] <Tom_itx> well at least look busy
[21:24:01] -!- zzolo has quit [Client Quit]
[21:26:55] <alex_joni> JT-Shop: inventory
[21:32:35] <andypugh> I have had a day rather like that too.
[21:32:57] <andypugh> I was rather counting on my new Mesa card turning up.
[21:35:28] -!- mhaberler has quit [Quit: mhaberler]
[21:35:29] * JT-Shop cuts a hole in the panel for the DB25 plug
[21:38:05] <kwallace> I'm looking at common grooving methods and found this: http://www.youtube.com/watch?v=NpzXnGW-oTI . I expected to see the tool only cutting in the X direction for roughing, then maybe drive along the finish profile at the end. What is the common way to make a simple groove?
[21:41:33] <Tom_itx> flat cutoff tool
[21:41:50] <JT-Shop> I use a grooving insert
[21:44:15] <kwallace> I'm used to not side cutting on a long reach tool.
[21:45:35] * roh doesnt need to cut.. these chinese machines are full of holes where db25 fit through
[21:46:16] -!- oyildirim has quit [Read error: Connection reset by peer]
[21:46:41] -!- oyildirim [[email protected]] has joined #linuxcnc
[21:46:52] <kwallace> I suppose as long as the depth of cut stays on a cutting edge, one could side cut as much as the acceptable flex will allow.
[21:50:04] <JT-Shop> seems logical
[21:51:19] -!- alpha1125 has quit [Quit: Computer has gone to sleep.]
[21:54:53] <DJ9DJ> gn8
[21:55:29] -!- DJ9DJ has quit [Quit: byte]
[21:55:55] -!- paideia has quit [Ping timeout: 252 seconds]
[21:56:21] -!- paideia [[email protected]] has joined #linuxcnc
[22:01:59] <andypugh> kwallace: Click the several "Film" links here: http://www.phorn.com/products/grooving/
[22:05:02] -!- pcw_home has quit [Remote host closed the connection]
[22:07:43] <kwallace> Oops, I just came back. I found this too: http://www.youtube.com/watch?v=mJAtCN61HNo
[22:09:40] <kwallace> I'm thinking about what a grooving wizard should look like.
[22:13:56] <andypugh> Groovy?
[22:18:45] <kwallace> It looks like the Fanuc G75 likes to rough with pecking to the groove floor, side stepping, pecking again, repeat until the groove width is roughed, then finish in one sequence down one side, along the floor, and up the other side. I think I'll shoot for that.
[22:37:03] -!- Valen [[email protected]] has joined #linuxcnc
[22:37:28] <kwallace> I seem to recall at one time Backplot or Gremlin could be run as a stand alone app. In other words - start LinuxCNC then open a terminal and start Backplot. Is anyone doing this now?
[22:49:14] -!- Valen has quit [Quit: Leaving.]
[22:51:57] -!- kwallace1 [[email protected]] has joined #linuxcnc
[22:53:19] -!- kwallace has quit [Ping timeout: 252 seconds]
[22:56:09] -!- artag has quit [Quit: leaving]
[22:57:46] -!- chillly has quit [Quit: Leaving]
[22:59:42] -!- Aero-Tec [[email protected]] has joined #linuxcnc
[23:05:53] -!- moonlite has quit [Ping timeout: 255 seconds]
[23:14:12] -!- Yarl has quit [Ping timeout: 265 seconds]
[23:17:53] -!- Valen [[email protected]] has joined #linuxcnc
[23:25:48] -!- cmorley1 [[email protected]] has joined #linuxcnc
[23:28:15] -!- cmorley has quit [Ping timeout: 260 seconds]
[23:30:30] -!- mikegg [[email protected]] has joined #linuxcnc
[23:30:50] <mikegg> howdy fellas
[23:33:54] -!- Nick001 has quit [Ping timeout: 240 seconds]
[23:34:36] -!- Nick001 [[email protected]] has joined #linuxcnc
[23:35:35] <mikegg> on a +/- 10 VDC spindle driver, using PID on velocity. Would it make sense to set the driver in torque mode or velocity mode?
[23:37:11] <andypugh> Probably velocity for a spindle
[23:37:26] <andypugh> Torque is likely to vary a lot in cutting.
[23:38:18] <andypugh> But then the question is whether the drive or LinuxCNC is best at controlling torque, as even a velocity-mode drive is a torque-mode drive when it comes to the actual current control stage
[23:39:17] <mikegg> huh. I thought in velocity mode the drive varies voltage and current does whatever it wants
[23:41:20] <andypugh> The drive varies PWM duty cycle, but the bus voltage is constant.
[23:50:03] -!- skunkworks [skunkworks!~chatzilla@str-broadband-ccmts-ws-26.dsl.airstreamcomm.net] has joined #linuxcnc